Only thing is, the OBDII version of the gauge (30-0334) "speaks" OBDII CAN protocol, instead of the AEMNet CAN protocol, like to 30-0300/0310. So, it MAY not work with the ProLink CAN input without being re-flashed back to the 30-0300 firmware. Depending on how HPTuners implements the interface.
it worked perfect first try this way when i did it on the MPVI2 and the latest software update as of when this was recorded. i have had some viewers say they needed to adjust parameters to what AEM had in the instruction... not sure why tho unless they were wonky before they started this process or were not on the latest HP tuners update.
Okay so ive got the AEM 30-0300 x series gauge. Can i use the CAN high and low wires instead of analog inputs to connect to my ProLink? I will have the whole Pro Features Kit.
Okay, so let me get this right. If I have the original mvpi2 non pro, and buy that $34 USB cable from hp tuners, follow your video, the aem wideband will work and log afr on my non canbus 2000 Corvette??
No... well not sure... I dont think it will work with out purchasing the pro feature. I purchased the pro feature and then did this because I wanted the MPVI2 to match the ease of the original MPVI Pro so I could quickly go from car to car.
I was just about to type the same. I'm assuming based on instructions they need to be on a key on wire and ground. My confusion is that the MPVI2 already has power so I'm assuming this power is for the gauge if you install. I will try without and then if something is off I will know to connect these.
I got a 2002 Ws6 Trans Am. I bought a new HP tuners MPVI2 standard and a new AEM 30-0300 wideband. So If i buy this HP tuners pro link and wire it up like you shown in this video, I will be able to data log?
thank you for this very good video,I have a 300c srt8 06. I did no pay attention and i got AEM 30-0333 X-Series Wideband with out using the obd2 Is it possible to send a signal like CONN A 3can L 4can H directly on the canL and canH on the car, or using rs232 connector pasthrought my MPVI and be on my computer to dataloging HPTuners please help i d'ont wont to buy a MPVI2 thank's
Nice surgery :) Keep those spare pins, though... The ProLink will eventually be able to read the 30-0300/0310 CAN data directly. Which is better than either the analog or OBDII data connection :)
that is very true sir but I got purchase happy when the MPVI2 was released so I wanted to get the Pro Feature like my original MPVI I have and in the long run its proved to be a much simpler set up when im using it daily in multiple vehicles
@@GonzosGarage I only have one car that uses the tuner so it dose not makes sense for me but if I use standalone data logging then it would be worth it.
The blue wire from the Pro Link is Analog 2, not 1 as described at 9:00.
This video is GOLD!
Amazing your awwesome great educational content
thanks man
The EXACT video i needed to see! THANK YOU!!!!!!!!!!!!!!!
I had to use perimeters in instructions to make mine read same in hp tuners as it did on gauge.
life saver
Thank you very much
How to I connect pro link cable to my aem 30-0300? Not quite understood as to how do it properly .
Or you can use the AEM 30-0300 and connect it through the EGR or other unused sensor in HP without buying ProLink stuff.
This is true but when you start tuning multiple vehicles a week and its not your car you dont want to start rigging up stuff to there harness.
When I cut my obd port of it had about 15 extra wires in there lol. Just tied them back. We'll see if it connects to software tomorrow 🤞 good video
Did you get it too work?
how did it go? everthing working now?
Yes got it to work 🤙
Only thing is, the OBDII version of the gauge (30-0334) "speaks" OBDII CAN protocol, instead of the AEMNet CAN protocol, like to 30-0300/0310. So, it MAY not work with the ProLink CAN input without being re-flashed back to the 30-0300 firmware. Depending on how HPTuners implements the interface.
it worked perfect first try this way when i did it on the MPVI2 and the latest software update as of when this was recorded. i have had some viewers say they needed to adjust parameters to what AEM had in the instruction... not sure why tho unless they were wonky before they started this process or were not on the latest HP tuners update.
Okay so ive got the AEM 30-0300 x series gauge. Can i use the CAN high and low wires instead of analog inputs to connect to my ProLink? I will have the whole Pro Features Kit.
Dude I bought the mpvi2,pro link and aem 30-300 and did exactly what you did and for some reason when I connect my car it disappears
did you just purchase the pro link pig tail or the complete Pro Feature Set?
So you're using two wires out of the prolink what do you do with the others
hey I followed your video step by step but its not working on my fbody. everytime I start the scan, the WB info disappears. any advice?
did you just purchase the pro link pig tail or the complete Pro Feature Set?
@@GonzosGarage Which do you purchase for aem 30-030 complete pro link feature set or pigtail harness you're referring to?
Or both?
Okay, so let me get this right. If I have the original mvpi2 non pro, and buy that $34 USB cable from hp tuners, follow your video, the aem wideband will work and log afr on my non canbus 2000 Corvette??
No... well not sure... I dont think it will work with out purchasing the pro feature. I purchased the pro feature and then did this because I wanted the MPVI2 to match the ease of the original MPVI Pro so I could quickly go from car to car.
Where I should connect the black and red wires that are in the other side of the connector
I was just about to type the same. I'm assuming based on instructions they need to be on a key on wire and ground. My confusion is that the MPVI2 already has power so I'm assuming this power is for the gauge if you install. I will try without and then if something is off I will know to connect these.
I got a 2002 Ws6 Trans Am. I bought a new HP tuners MPVI2 standard and a new AEM 30-0300 wideband. So If i buy this HP tuners pro link and wire it up like you shown in this video, I will be able to data log?
only if u have the pro feature set purchased for ur mpvi2. u can use the same wires but run it to ur Serial port on ur laptop.
thank you for this very good video,I have a 300c srt8 06. I did no pay attention and i got AEM 30-0333 X-Series Wideband with out using the obd2 Is it possible to send a signal like CONN A 3can L 4can H directly on the canL and canH on the car, or using rs232 connector pasthrought my MPVI and be on my computer to dataloging HPTuners please help i d'ont wont to buy a MPVI2 thank's
in theory yes that should work but i havent tried it that way. sorry i didnt get back to you sooner. did you get it all sorted out?
Did you need to purchase the pro software as well or just the pro link cable
You'll need to purchase the Pro Features Set for the MPVI2. It includes the software and the pro link cable for $249.99. I just bought mine.
Nice surgery :) Keep those spare pins, though... The ProLink will eventually be able to read the 30-0300/0310 CAN data directly. Which is better than either the analog or OBDII data connection :)
Yeah I know. Cant wait for them to get all the Pro Link software finish.
Have they came out with this capability yet?
@@utubeacount10 Yes,
I would rather buy a serial adapter and use that instead way cheaper than a pro upgrade
that is very true sir but I got purchase happy when the MPVI2 was released so I wanted to get the Pro Feature like my original MPVI I have and in the long run its proved to be a much simpler set up when im using it daily in multiple vehicles
@@GonzosGarage I only have one car that uses the tuner so it dose not makes sense for me but if I use standalone data logging then it would be worth it.
do you have a tutorial for that?
What if you have the AEM 30-4110?
works the same.