I used this guide to replace my battery, thanks! Make sure you have the perfect Phillips screwdriver for the job. You will easily wreck these delicate little screws. Also - some of them are pointy and others are square. Make note of which goes where. I didn't have any fancy silicone or glue to close the hole above the battery. I don't think it makes any difference. Good luck. And to JBL: You could build it so the battery is a lot easier to replace. There's no planet B you know.
The silicone or glue is there in order to eliminate any vibration, in time you may hear the battery knocking about. The silicone on the wires and hole to the battery is a good precaution to prevent moisture causing corrosion, it will extend the life of your speaker, ain't nothing fancy about silicone, cheap at any hardware store.
Thanks for the warning re: screws. Otherwise I'd assume they're all the same. I hope your Flip 3 is still fine. I just replaced mine's battery after 7 yrs.
Thanks for the video. It gave me the confidence to order a replacement battery rather than buy a new system. I was able to follow these instructions and take everything apart very easily. My battery was very swollen so it’s no wonder I was having problems. Cheers
Hey Spencer Jose how did you remove the glue and the black tar to be able to unplug the battery from the circuit? I just opened mine and same issue as yours
Mr. Moreno I just picked it with needle nose pliers and a flathead screwdriver if I remember correctly. Don’t have to be overly careful seeing as the battery is no good and the silicone has to be replaced.
Thanks so much for this video... I wouldn't be able to replace the battery without this clear guide. Now my jbl flip3 is as good as new with just merely a fraction of the cost instead of buying a new one.
Perfeito o vídeo explicativo. Bem didático e, inclusive me deu forças para solicitar pela Internet a bateria para reposição. A questão do silicone, eu entendo que seria para não ocorrer vibrações. Vale a pena realizar essa mão de obra. É uma terapia ocupacional e, quando o produto é seu, você mesmo o fará com mais carinho. Uma dica: dobrar uma toalha para servir de apoio! Em se tratando de uma JBL vale o investimento e dedicação, afinal a qualidade dessa caixinha étudo de bom! Abraço!
Lithium Polymer (Li-Po) batteries do not like to be stored at full or empty charge for extended time, if not using any electronic device for extended time try to store them at 50% charge (storage voltage) and the Li-Po will last much longer..
Too bad mine had the plastic soldered through and through. The cable was melded on the plastic and the substitution was impossible, unless I drilled a hole in the hard plastic. Lasted almost 4 years but really bummed I couldn't change the battery (swollen). Never mind, I managed to remove the battery without problems, the black plastic made it look like it was a single slab of hard plastic, instead it was the "silicone". Ordered a new battery from amazon, will update if it works as intended :D Battery arrived, followed the guide and it works! Will update on the quality of the battery but I hope I'll manage another coupla years of usage. The sound quality is very good for its size.
Good video. My batteri was very swollen and impossible to pull out. Had to drill (non pointy hss drill to not damage battery) a 6mm hole to the other end of the battery compartment which could be accessed from the other end of the unit and push it out with an allen wrench like I noticed someone do on a newer model with better access. Got the job done in case someone struggles with the same issue
@@rzely1 In mine if I remember accuratly there was a screw with a washer in it which I removed and behind it an there was an incline that ended behind the bottom of the batteri compartment which is big enough to fit a drill bit.
I haven't tried this replacement yet, but from all I've read many people do not have the skills or tools, or patience. Don't use the cheap tools that come with some of these replacement batteries, they're junk. Get some quality precision screwdrivers, a phone repair set is ideal. You have to carefully think through each step. Never use force, glue can be broken down with heat, but on this speaker, I wouldn't advise it. Slowly breaking the glue seal with a painter's putty knife is ideal. The smartest thing to do would be to sharpen the end and heat it and slowly work it down the side of the battery till it comes free. He does quite well in this breakdown, but I would advise taking the flat ribbon cable off before removing the battery, if he slipped or if the battery suddenly came loose he could have easily ripped the ribbon cable. Be very gentle with the ribbon cable and especially the plug and connector, lift the plastic locking tab before pulling on it. Ribbon cables are very fragile.
Add me to the list of Flip 3 users you helped. Thanks for the tutorial 🙂. My Flip 3 is 7 yrs old, and it's my first time to replace the battery. When it was 6.5 yrs old, it could still work for 4 hours (10-12 when new). Then one day, it's suddenly down to 10 minutes only. But now it's back. Such a nice and speaker. I hope to get a few more years out of it. PS. I didn't apply any silicone in the hole where the battery cable runs thru. What will be the effect? Will the bass be affected, or anything else?
@KonstantinSachkov oh I see.. I do hear a faint rattling at full volume, or when playing very strong bass. Will add some silicone later. Thank you again sir. 🙂
Has anyone done this to fix a squeaky playback? My battery on this model will say fully charged but then playback is terrible, becomes squeaky and sounds like nails on a chalk board. Then it automatically turns off. Would it be worth just trying to change the battery, or will I need a new speaker?
strange, I don't know if I have the same JBL Flip 3, but after opening the outer shell, I can't find the three screws to open further. In the parts where the screws should be I only have plastic. Will try to open it up further anyway.
Turns out, I had another model. In my model I had to get the outer speakers out and try to slide the battery out, which turned out to be impossible due to the amount of glue they put. Ended up tossing my JBL Flip 3.
Is this the solution for when the Flip 3 suddenly starts “screaming” even though it is fully charged? I’ve used it only very occasionally for about five years, and I’m wondering if this loud, ugly noise that I’m hearing after running it for only about an hour now is a battery issue.
Use a spudger like he did. You'll have to exercise some traction but it's pretty sturdy (the Jbl plastic, that is), try to use a flat surface so as to minimize the dents.
@@benthorney5080 No prob, every time I try to open one of these devices I fear breaking everything. If the plastic is not too used and old, it's pretty elastic and sturdy.
Dankeschön für die Anleitung. Bei meinem Flip3 waren allerdings der Akku und die Kabel alle eingeklebt und nicht mehr zu lösen. Ärgerlich,aber nach fast 10 Jahren geht das Teil nun in den Elektroschrott! JBL?? Nie mehr, habe mir nun BOSE gekauft! 👍🏻👍🏻👍🏻
@@KonstantinSachkov I have a flip 3 and the problem is JBL is not getting charged only charging indication blinking , ports are fine do I need to replace the battery or there can be a problem with charging port.
Есть какие-то отличия по батареям в зависимости от парт-номера ? или важна только модель аккумулятора ? иными слвоами если покупной аккумулятор отличается только парт-номером, но не моделью подойдет или нет или нужно чтобы парт-номер аккуумулятора и модель совпадали 100% или не обязательно - чтобы подошел по размерам, вольтажу, распиновке коннектора и т.д ? И подойдет ли аккумулятор от Flip 4 для Flip 3 ?
@@KonstantinSachkov а если коннектор перепаять , как я понял разница в батереяхля флип3/4 в порядке проводов к коннектору ? т.е взять батарею для 4, и припаять колодку для флип3 поставив правильно провода, или просто перевоткнув в сам разъём, вроде бы провода оттуда можно достать аккуратно.
Thank you for your vid ! I have 2 questions : what size of tape did you use ? And I have seen on other videos that the battery is often glued, did you not have the problem ?
3 года назад
And what are the white and the black sort of tape you use ^^ ?
It's easy to replace, but it'd be hard to find a new socket. It might be easier to install some usb-c socket from phone, you can find many different types on AliExpress.
@@qurex1808 it's not possible. All lion batteries have almost the same capacity/size ratio. Big numbers that you can find on many cheap batteries just a fantasy of marketing.
It looks like you used double sided tape. Is it a special kind of tape or can you use any double sided tape??? Also can you use the silicon to glue the battery down instead of the double sided tape?
Thx i changed my Battery in 20min but maybe should show all the screws which need to be removed there are a lot more than someone expect of this Video.
Yeah more than 10 screws, then again once you get "the lay of the land" you're able to manage. Unlike some devices that got different screws for different parts of the device...
@@KonstantinSachkov так ведь в место где расположен акб и место куда уходит кабель уже защищено от воды.... Если в одном из этих "отсеков" окажется вода, колонке хана. Собственно поэтому и появился вопрос. Чтобы провода не гремели... Весьма странно. Возможно герметизация нужна для того, что бы в отсеке динамиков сохранялся отдельный вакуум для правильного звучания колонки
mano, essa porra de caixinha tá custando 200 conto, e a bateria no mercado livre também. bagulho perdeu o valor violentamente, e uma pena que a flip 4 tá custando 800 reais. tava procurando aqui pra ver de fazer esse procedimento na minha caixinha tb, mas agora to pensando é em comprar uma nova. abração meu caro!
Old one was completely dead, charge was enough just for a minute. And it swelled very much, only power button worked. The first Flip3 did the same after 10 months, so I replaced it. This one broken after 1.5 year.
Does anyone have a problem with their flip 3? I only had mine for about 9 months and took very good care of it. However, the speaker constantly turns on and off by itself. The power button is stuck. The only way for me to turn it on or off is if I squeeze the hell out of the speaker on the side, weird I know. Also, it only works now if I have it plugged on the charger. I’m assuming my battery is pretty much done. It hasn’t been a year and I’m already having problems. Can someone please help. Thanks
I used this guide to replace my battery, thanks!
Make sure you have the perfect Phillips screwdriver for the job. You will easily wreck these delicate little screws. Also - some of them are pointy and others are square. Make note of which goes where. I didn't have any fancy silicone or glue to close the hole above the battery. I don't think it makes any difference.
Good luck.
And to JBL: You could build it so the battery is a lot easier to replace. There's no planet B you know.
The silicone or glue is there in order to eliminate any vibration, in time you may hear the battery knocking about. The silicone on the wires and hole to the battery is a good precaution to prevent moisture causing corrosion, it will extend the life of your speaker, ain't nothing fancy about silicone, cheap at any hardware store.
@@EnzoFerenczyowill this affect the sound though? I don't use my Flip 3 in moist environments so moisture is not a concern for me.
Thanks for the warning re: screws. Otherwise I'd assume they're all the same. I hope your Flip 3 is still fine. I just replaced mine's battery after 7 yrs.
Thanks for the video. It gave me the confidence to order a replacement battery rather than buy a new system. I was able to follow these instructions and take everything apart very easily. My battery was very swollen so it’s no wonder I was having problems. Cheers
Hey Spencer Jose how did you remove the glue and the black tar to be able to unplug the battery from the circuit? I just opened mine and same issue as yours
Mr. Moreno I just picked it with needle nose pliers and a flathead screwdriver if I remember correctly. Don’t have to be overly careful seeing as the battery is no good and the silicone has to be replaced.
Thanks so much for this video... I wouldn't be able to replace the battery without this clear guide. Now my jbl flip3 is as good as new with just merely a fraction of the cost instead of buying a new one.
Thanks so much for this video
Hey, where did u get the battery from and how is it working now?
Awesome. It was pretty easy to replace the battery following your instructions
Perfeito o vídeo explicativo. Bem didático e, inclusive me deu forças para solicitar pela Internet a bateria para reposição. A questão do silicone, eu entendo que seria para não ocorrer vibrações. Vale a pena realizar essa mão de obra. É uma terapia ocupacional e, quando o produto é seu, você mesmo o fará com mais carinho. Uma dica: dobrar uma toalha para servir de apoio! Em se tratando de uma JBL vale o investimento e dedicação, afinal a qualidade dessa caixinha étudo de bom! Abraço!
Lithium Polymer (Li-Po) batteries do not like to be stored at full or empty charge for extended time, if not using any electronic device for extended time try to store them at 50% charge (storage voltage) and the Li-Po will last much longer..
9999jin0
And how to charge it for longer battery health, full charge and full discharge is this damage the speaker
Music sounded like he's trying to disarm a bomb! Nice!
😂😂
Thank you very much! This helped me fix my JBL flip 3!
Too bad mine had the plastic soldered through and through. The cable was melded on the plastic and the substitution was impossible, unless I drilled a hole in the hard plastic. Lasted almost 4 years but really bummed I couldn't change the battery (swollen). Never mind, I managed to remove the battery without problems, the black plastic made it look like it was a single slab of hard plastic, instead it was the "silicone". Ordered a new battery from amazon, will update if it works as intended :D
Battery arrived, followed the guide and it works! Will update on the quality of the battery but I hope I'll manage another coupla years of usage. The sound quality is very good for its size.
I used a butter knife to get my cover off haha. Thanks for the fantastic video - I have a new life for my speaker!
Good video. My batteri was very swollen and impossible to pull out. Had to drill (non pointy hss drill to not damage battery) a 6mm hole to the other end of the battery compartment which could be accessed from the other end of the unit and push it out with an allen wrench like I noticed someone do on a newer model with better access. Got the job done in case someone struggles with the same issue
Sounds good; I could not find a proper place to dril with the flip 3..
@@rzely1 In mine if I remember accuratly there was a screw with a washer in it which I removed and behind it an there was an incline that ended behind the bottom of the batteri compartment which is big enough to fit a drill bit.
Thank you! Mine was doing some weird stuff and figured it was battery. Made it very easy to replace the battery!
from where did u order?
Anyone know where I can get replacement ribbon cables...the 2 shown at the 2 minute mark.
I haven't tried this replacement yet, but from all I've read many people do not have the skills or tools, or patience. Don't use the cheap tools that come with some of these replacement batteries, they're junk. Get some quality precision screwdrivers, a phone repair set is ideal.
You have to carefully think through each step. Never use force, glue can be broken down with heat, but on this speaker, I wouldn't advise it. Slowly breaking the glue seal with a painter's putty knife is ideal. The smartest thing to do would be to sharpen the end and heat it and slowly work it down the side of the battery till it comes free.
He does quite well in this breakdown, but I would advise taking the flat ribbon cable off before removing the battery, if he slipped or if the battery suddenly came loose he could have easily ripped the ribbon cable.
Be very gentle with the ribbon cable and especially the plug and connector, lift the plastic locking tab before pulling on it. Ribbon cables are very fragile.
Add me to the list of Flip 3 users you helped. Thanks for the tutorial 🙂. My Flip 3 is 7 yrs old, and it's my first time to replace the battery. When it was 6.5 yrs old, it could still work for 4 hours (10-12 when new). Then one day, it's suddenly down to 10 minutes only. But now it's back. Such a nice and speaker. I hope to get a few more years out of it.
PS. I didn't apply any silicone in the hole where the battery cable runs thru. What will be the effect? Will the bass be affected, or anything else?
@@MasterKoala777 great! Glad for you! This wire may produce some rattling sound on high volume.
@KonstantinSachkov oh I see.. I do hear a faint rattling at full volume, or when playing very strong bass. Will add some silicone later. Thank you again sir. 🙂
my charging port is almos borken too. any chances??
Has anyone done this to fix a squeaky playback? My battery on this model will say fully charged but then playback is terrible, becomes squeaky and sounds like nails on a chalk board. Then it automatically turns off. Would it be worth just trying to change the battery, or will I need a new speaker?
Change the battery.
strange, I don't know if I have the same JBL Flip 3, but after opening the outer shell, I can't find the three screws to open further. In the parts where the screws should be I only have plastic. Will try to open it up further anyway.
Turns out, I had another model. In my model I had to get the outer speakers out and try to slide the battery out, which turned out to be impossible due to the amount of glue they put. Ended up tossing my JBL Flip 3.
@@ryuuzaki24 it's another version (old one). Try using alcohol and heat air gun, it's possible 😉
Thanks! Ok, I will try again, let's see
Same here. What a lousy production process... there is glue everywhere!
and What is that clear paste you putted on the cables ?
Silicone
@@KonstantinSachkov how we know the battery is the problem?? can you explain please ?
@@johnnytallo it doesn't work more than 1-2 hours after charging.
@@KonstantinSachkov thank you dear
A special type of silicone or not a specific silicone?
Thanks.
Is this the solution for when the Flip 3 suddenly starts “screaming” even though it is fully charged? I’ve used it only very occasionally for about five years, and I’m wondering if this loud, ugly noise that I’m hearing after running it for only about an hour now is a battery issue.
Possibly it is a battery. Original battery can't live so long 😁
Did the replacement of the battery make anyone's speaker stop having that screeching noise??
Also wondering this
Just found out that when my flip 3 is charging the screeching noise doesn't occur but when it's not it happens
donde compraste la batería, no la puedo pillar
Thanks! I managed to change my battery (almost) effortlessly!
Is it hard to take off the grill, and can it be damaged by taking it off?
Use a spudger like he did. You'll have to exercise some traction but it's pretty sturdy (the Jbl plastic, that is), try to use a flat surface so as to minimize the dents.
@@azmodanpc thanks for the help, but i got it off ages ago
@@benthorney5080 No prob, every time I try to open one of these devices I fear breaking everything. If the plastic is not too used and old, it's pretty elastic and sturdy.
Thank you very much , Your video is awesome.👍👍👍
es un pegamento lo que se le pone en los cables de la bateria? Que roducto es?
Silicon
Dankeschön für die Anleitung. Bei meinem Flip3 waren allerdings der Akku und die Kabel alle eingeklebt und nicht mehr zu lösen. Ärgerlich,aber nach fast 10 Jahren geht das Teil nun in den Elektroschrott! JBL?? Nie mehr, habe mir nun BOSE gekauft! 👍🏻👍🏻👍🏻
how we know the battery is the problem?? can you explain please ?
It will go from a full charge (five lights on) to two or less very quickly, within minutes.
Was not expecting the base was using earbuds and caught me off guard! Great video tho
Спасибо, видео довольно качественное. Приятно смотреть. Удачи
Is it compulsory to change the battery 🙁
Hey i have a flip 3 and my problem is it always tuns off after 1or 2 songs. Do i need to change my battery ?
Yes
@@KonstantinSachkov I have a flip 3 and the problem is JBL is not getting charged only charging indication blinking , ports are fine do I need to replace the battery or there can be a problem with charging port.
@@rvmec081 replace the battery
Why we need to put the high temp adhesive tape on the battery?
To make it looks perfect 😀
Got a flip 3.. if it wont fully charge - 5th light stays flashing during charging - is the battery bad? Great video & thank you
It's ok. Flip3 leds are crazy a bit.
@@KonstantinSachkov ok thank you 🤓
Есть какие-то отличия по батареям в зависимости от парт-номера ? или важна только модель аккумулятора ? иными слвоами если покупной аккумулятор отличается только парт-номером, но не моделью подойдет или нет или нужно чтобы парт-номер аккуумулятора и модель совпадали 100% или не обязательно - чтобы подошел по размерам, вольтажу, распиновке коннектора и т.д ? И подойдет ли аккумулятор от Flip 4 для Flip 3 ?
Есть отличия в зависимости от производителя, в качестве и сроке службы батареи. Батарея подойдёт только от flip3.
@@KonstantinSachkov а если коннектор перепаять , как я понял разница в батереяхля флип3/4 в порядке проводов к коннектору ? т.е взять батарею для 4, и припаять колодку для флип3 поставив правильно провода, или просто перевоткнув в сам разъём, вроде бы провода оттуда можно достать аккуратно.
My 1 speaker of jbl flip 3 sound bur bur how to clear dis also needs battery to be replaced???
If it works without charger short time, you should replace battery.
@@KonstantinSachkov how much money spend for battery🔋
Please tell me my whatsup number 7020666234
@@amitkashte5673 $18, link in description
Cool dude!! Pretty easy fix! Thx 👌
👍
What kind of tape is used at 5:25 mark?
ali.pub/4wmm4m
Thank you for your vid ! I have 2 questions : what size of tape did you use ? And I have seen on other videos that the battery is often glued, did you not have the problem ?
And what are the white and the black sort of tape you use ^^ ?
High temperature adhesive tape (yellow) is 15 mm size, link in description. And any thin double side adhesive from local shop.
@ black tape was originally sealed.
Parabéns pelo seu belo trabalho 👏👏👏👏👏👏
Thank you sooooo much. I was able to replace the battery and enjoy my JBL again.
What song is being used?
Navajo Night by Audionautix
the soundtrack is quite surprising and mermerizing
Adónde puedo comprar la batería
What's the silicone for?
To keep it waterproof.
What is the silicone for? Is it necessary?
To save waterproofing
What about the charger port how would you replace that
It's easy to replace, but it'd be hard to find a new socket. It might be easier to install some usb-c socket from phone, you can find many different types on AliExpress.
@@KonstantinSachkov OK thanks
Que tipo de cita es ??
What is the yellow clear tape he uses on the battery?
Polyimide High Temperature Adhesive Insulation Tape, it's a bit better than usual clear tape.
Is it hard to put grill back on and take it off
No, with the right tool and patience it's a cinch.
Can you replace the old batterie with a new one that has more power.?
More power? Do you mean external battery? You can connect any USB power bank.
İ think he means more mah in the battery
@@proxyhx2075 yes
@@KonstantinSachkov I mean more mAh
@@qurex1808 it's not possible. All lion batteries have almost the same capacity/size ratio. Big numbers that you can find on many cheap batteries just a fantasy of marketing.
It looks like you used double sided tape. Is it a special kind of tape or can you use any double sided tape??? Also can you use the silicon to glue the battery down instead of the double sided tape?
You can use any. It's better to use tape (buy in automobile shop) than silicone.
Спасибо, поменял четко по инструкции!
where to buy the battery?
Link in description
Where should I get battery for flip 3.
Look at description
Thanks a Million
Very clear and i was able to follow and accomplish :)
@GloGang Saint It will only get worse. Eventually, you will.
Can I put a flip 5 battery in instead for better life
You have to check the voltage to make sure it's the same and make sure it will fit but could be possible!
Where will I get the new battery
Link in description
If the new battery already has the wire on it why didn't he just clip the old one off instead of working to force it through a little hole
Because then you have to put it back
You have to open that rubberized hole because the new harness wont pass through without removing it.
Where can we find the battery?
Link in description
How do I fix mine it doesn’t turn on it only turns on when I plug it in
Change battery as in video
how about flip 5
What kind of silicon was it sorry brother
Anyone from Plumbing Supply Store
@@KonstantinSachkov thanks copy that
чуть не выбросил колонку:) спасибо за видео
worked for me, very useful - thanks!
Avery nice and detailed fix, Thanks!!!
Thanks! - worked like a charm 😊
der dekt auch nicht nach das sind die sachen die eaby laden und man bekomt nix mher auseinder
Подскажите, аккумуляторы на Flip3 и Flip4 подходят друг к другу?
Думаю что нет, слышал, что разъем разный.
@@KonstantinSachkov понял, спасибо
Congratulations! Nice video
Bro my JBL Pulse 4. Next JBL flip 3 no working pliz halp me 🥵 how to make bro
Why apply silicone?
To make it waterproof again
I assumed it has to do with the bass passive radiators performance
vu le paquet de neoprène ,je pense qu'il ne cpt plus jamais changer sa batterie..je ne comprend pas non plus pourquoi tant se schotch
Excelente cambio solo que es algo de silicón el que ocupa algo que va a batallar para quitar en otro posible cambio de batería 😃
How to I collect tha battery Can you give me address?
Link in description
Thx i changed my Battery in 20min but maybe should show all the screws which need to be removed there are a lot more than someone expect of this Video.
Yeah more than 10 screws, then again once you get "the lay of the land" you're able to manage. Unlike some devices that got different screws for different parts of the device...
2 Speaker boton no working mor tary no sound why plaz halp me good pormase I'm seras 😔
bravo 👏👏
No you F%&*ing B€$@
Для чего в месте прохода кабеля от акб залито герметиком ???
Для герметичности колонки, обещали ж защиту от воды. И плюс чтобы не гремели провода.
@@KonstantinSachkov так ведь в место где расположен акб и место куда уходит кабель уже защищено от воды.... Если в одном из этих "отсеков" окажется вода, колонке хана. Собственно поэтому и появился вопрос. Чтобы провода не гремели... Весьма странно. Возможно герметизация нужна для того, что бы в отсеке динамиков сохранялся отдельный вакуум для правильного звучания колонки
This is crazy to get to the battery. I don't think I will be doing this
It’s really easy, I did it with this video
Onde faz isso aqui no RJ (Brasil) ?
mano, essa porra de caixinha tá custando 200 conto, e a bateria no mercado livre também. bagulho perdeu o valor violentamente, e uma pena que a flip 4 tá custando 800 reais. tava procurando aqui pra ver de fazer esse procedimento na minha caixinha tb, mas agora to pensando é em comprar uma nova. abração meu caro!
Why would you have to replace a battery?
Old one was completely dead, charge was enough just for a minute. And it swelled very much, only power button worked. The first Flip3 did the same after 10 months, so I replaced it. This one broken after 1.5 year.
@@KonstantinSachkov thanks. I did not know the battery would do that.
Mine is about 2 yrs old and only holds a 1 hr charge. Wonder how much a new battery is.
@@wadep9916 link in description.
@@KonstantinSachkov if you replace the the battery would it still be water resistant after
Why does the audio sound like it was recorded inside a human?
Im not finding as a easy thing to close it.
Si lo ubiera visto antes no rompía el flex tratando de arrancar la bateria
Excellent! I did it!
Por aquaso o senhor trabalhar como o conserto de caixa de som jbl
Jbl flip 3 price......?
300zl or 90$
Mybe can find some mobile batery with much amp Like 4000mah or higher,Ford many cash ,yust must size be same, sorry for my bad English
Pin mua ở đâu vậy bạn
Link in description.
Does anyone have a problem with their flip 3? I only had mine for about 9 months and took very good care of it. However, the speaker constantly turns on and off by itself. The power button is stuck. The only way for me to turn it on or off is if I squeeze the hell out of the speaker on the side, weird I know. Also, it only works now if I have it plugged on the charger. I’m assuming my battery is pretty much done. It hasn’t been a year and I’m already having problems. Can someone please help. Thanks
It looks like your Flip3 battery is dead and became bigger. The same as two mine flip 3's
thank you for video
ขอบคุณครับ
You are pro!! 😎
Thanks for video
Thank you!
But Sound Not Good
If your flip 3 don't looks like on a video better buy a orginal one :D Yes, its true flip 3.
i thought i broke my speaker for a second lol
хорошее видео, герметика много