Replacing Copper Pipes and Fittings with SharkBite Push Fit Connectors

Поделиться
HTML-код
  • Опубликовано: 13 июн 2024
  • Replacing copper pipes and fittings with SharkBite push fit connectors is super easy. Today I'm going to show you how I used SharkBite fittings to save some money on a plumbing fix. You only need a few tools to do this yourself and it will like take 30-60 minutes, depending on your skill level. I replace an old shutoff valve in our basement and share how SharkBites make this process very simple. If you have your own tips please add them to the comment section so that we can all learn.
    For more tips on how to replace copper pipes using push fit connectors visit:
    www.homerepairtutor.com/using-...
    For a 1/2" x 1/2" sharkbite shut-off valve: amzn.to/2irnz4W
    Some product links may be Amazon affiliate links. As an Amazon Associate we earn from qualifying purchases at no additional cost to you.
    0:00 How to Replace Copper Fittings with SharkBites
    0:08 How to Drain and Cut the Pipe
    1:42 How to Remove the Old Valve
    2:11 How to Slide on SharkBite Shutoff Valve
    3:24 Place marks for SharkBite Slip-in Fitting and Copper Pipe
    4:35 How to Assemble New Connections
    #replacecopperpipe #sharkbitefittings #pushfitplumbing
    Want our newest DIY videos? Subscribe to our channel and hit the notification bell to see every upload. We upload new videos every Saturday.
    Disclaimer:
    Videos produced by Home Repair Tutor are provided for informational, educational, & entertainment purposes only. Some of these projects, materials, and techniques may not be appropriate for all ages or skill levels. Home Repair Tutor does not make any claims of the safety of the projects, techniques, or resources listed on this site and will not take responsibility of what you do with the information provided by this site. Viewers must be aware by doing DIY projects on their homes they are doing it at their own risk and Home Repair Tutor cannot be held liable if they cause any damage to their homes. Home Repair Tutor cannot claim liability with all applicable laws, rules, codes and regulations for a project.
  • ХоббиХобби

Комментарии • 438

  • @roshi98
    @roshi98 3 года назад +42

    Always deburr the pipe before installing a SharkBite fitting. Also, when dealing with copper pipe and non-conductive brass SharkBite fittings, it's a good idea to install grounding clamps connected by a copper wire on opposite sides of the new fitting to ensure good grounding, which prevents possible shock and preserves the integrity of the copper pipe.

    • @c0rnd0g_19
      @c0rnd0g_19 Год назад

      10 years later I also noticed the grounding clamp and these Sharkbite connectors are breaking that ground so need to have a ground strap bridging them!!

    • @ryanbrophy8814
      @ryanbrophy8814 9 месяцев назад +2

      wouldn't the water inside be conductive to transfer from copper to the other copper pipe?
      I'm not being smart, just curious.

  • @bshockley4
    @bshockley4 5 лет назад +13

    This video was great and it helped me replace the 30 year old shutoff valves without having to call the $75 and hour plumber. No leaks...shark bite fittings rock! Thanks for the video and helping me build my plumbing confidence!

    • @HomeRepairTutor
      @HomeRepairTutor  5 лет назад +1

      awesome, hope all the tips help with other projects!

  • @vicmeyers1243
    @vicmeyers1243 Год назад +2

    You do a great job of making a how-to video. No extraneous nonsense. Not to fast. Clear explanations. I didn't have any questions because you were thorough. Thank you. Subscribing.

  • @davidsciuto8011
    @davidsciuto8011 11 лет назад +1

    Jeff, your style is so easy to watch and understand. Thank you so much!!! Wife and I Cant wait to get started on our home project. Us DIY'ers really appreciate the simple and clear delivery. Much appreciated. GO SharkBite!!!

  • @adofilth
    @adofilth 7 лет назад +10

    I did same exact thing yesterday with 3/4" shut off valve and 3/4" sleeve and it worked like a champ!

  • @geoengr3
    @geoengr3 3 года назад +2

    Thanks for making this video. There are so many instructions out there for how to do a new install with shark bite. Yours was the first I came across which shows how to replace a valve, which is exactly what I need to do!

  • @jimchristman3740
    @jimchristman3740 8 лет назад +3

    Thanks for posting your video. After watching it I was able to add a shut off valve to a 1/2 line that supplies an outside faucet. Good Job.

  • @CaptainO3E
    @CaptainO3E Год назад +2

    Used this for the first time and am absolutely amazed at how well it works.

  • @xinliu4613
    @xinliu4613 3 года назад +2

    I love shark bites. Last week I replaced all of the water piping in my house from galvanized steel to copper and used shark bites to connect everything behind my walls. Supposedly they are built to last decades so I should be good. I saved thousands of dollars by not hiring a greedy plumber by doing it on my own. I showed my wife who the handyman of the house is later that night ;)

  • @HomeRepairTutor
    @HomeRepairTutor  11 лет назад +1

    Thanks Brian, I've fiddled with this kind of setup before and had some issues. The slip fitting just makes is so much easier and faster to complete. Hope you had a great day.

    • @sunrise8263
      @sunrise8263 3 года назад

      In my experience, I believe it is impossible without the use of a slip coupler. I tried using Sharkbite straight couplers on each end of a replacement piece of PEX, thinking that PEX would be flexible enough that I could slide each end into a fitting. [And the "official" Sharkbite videos never address this issue.] But it has never cucceeded, so I had to use either CPVC or copper and a slip coupling on one end. Be sure to note --- and Sharkbite DOES mention this, but does not stress it --- the slip couplings are intended for use ONLY on copper or CPVC ... not on PEX or "regular" PVC. The straight couplings work on nearly anything, but the slip coupling REQUIRES copper or CPVC [or, one of each on each end, of course].

  • @bcsimpilot3497
    @bcsimpilot3497 Год назад +1

    What a great tool, none of the screw down type that sticks up so far! Excellento!

  • @hearnjack
    @hearnjack 5 лет назад +2

    I installed one of these a couple of years ago so I could take off the outdoor faucet and put new siding on. I just now reinstated a new outdoor faucet. I was amazed how the shutoff never leaked in two years just hanging by itself. I slid the old pipe right in and heard a click. What a product. I'm impressed.

    • @johanandersson2165
      @johanandersson2165 2 года назад

      That's amazing a pipe fitting that hasn't leaked in TWO years.

  • @mrcraigjohnson2000
    @mrcraigjohnson2000 4 года назад +2

    Thanks for this video. I had the same situation and your video helped me get through it in about 20 minutes of actual work (not counting trips to Home Depot...) :)

  • @stanvideo
    @stanvideo 10 лет назад +2

    This is exactly the work which I have to do in my house. Thanks a lot for this video. Very helpful and informative.

    • @HomeRepairTutor
      @HomeRepairTutor  10 лет назад

      Glad to help you, I hope your project goes well. If you have any questions just let me know.

  • @MartinD9999
    @MartinD9999 6 месяцев назад +1

    That was awesomely easy! Thanks guy!

  • @703am
    @703am 5 лет назад +3

    i just recently used this type of shutoff valve and so far all is good

  • @TooManyCats77
    @TooManyCats77 3 года назад +1

    Thank you so much for this video. Being a woman (and not being able to afford Mr. Darren below!) I can do this quick fix. I will follow all the advice below also. Plumbers are more expensive than financial planners with half the education. You should see the house my plumber lives in. We've been had. Thanks guys and I'm from Pittsburgh too.

  • @mypointofblue5260
    @mypointofblue5260 4 года назад +3

    Thanks for the video. I'll be heading to home depot to try this myself! :)

  • @wingmanalive
    @wingmanalive 8 лет назад +4

    Thanks. I used your procedure almost to the button and used exactly same fittings. I'm amazed these types of fittings work so well without a single drop of leaks. They are pricey but worth it. I used mine for a replacement 3/4" water main valve. The ball type valves are so much more reliable. Plus I saved myself a good $250+ calling a plumber.

  • @copernicus633
    @copernicus633 3 года назад +18

    You should ALWAYS deburr both the inside and outside of the pipe end. Failure to do that may allow a burr to nick the sealing gasket. Also, DONT sandpaper the pipe end like you would for soldering. You want a smooth seating surface for the gasket.

    • @Mattg1616
      @Mattg1616 7 месяцев назад

      sooooo...what do you do for painted pipe?

  • @jeannamonsibais3137
    @jeannamonsibais3137 2 года назад +1

    Awesome video thank you for taking the time to create this!

  • @Ranger42
    @Ranger42 8 лет назад +1

    Excellent instructional video. Always wondered how one would accomplish this type of connection. Thank you.

    • @HomeRepairTutor
      @HomeRepairTutor  8 лет назад

      Thanks, after doing it a few times it gets even easier

  • @MrJimmy-ox7fq
    @MrJimmy-ox7fq 3 года назад +3

    Thank you very taking the time to post a video. If I may, copper should (must) always be cleaned with emery cloth and deburred prior to attaching this type (or soldering) a connector to ensure a tight seal. The way you showed may not leak, but why chance it for a few extra seconds of work? Again, thank you for this helpful video.

  • @sachintr11
    @sachintr11 8 лет назад

    very helpful. did my job.thanks

  • @johnmonk66
    @johnmonk66 11 лет назад

    Just had a water heater go bad, thanks to your video I pit a shutoff on the tank feed, and I still have cold water until I repair it. And thanks to you I am confident to instal a new tank by myself.

  • @TheJoegassaway1992
    @TheJoegassaway1992 7 лет назад +2

    THANK YOU SO MUCH! I was way over thinking replacing a water shutoff in my basement

  • @cedricpod
    @cedricpod 5 лет назад +2

    Thanks Steve and Jeff worked for me

  • @MarcellePierson
    @MarcellePierson 3 года назад

    Thanks so much for this, very helpful!!

  • @DrRichardHagmeyer
    @DrRichardHagmeyer 10 лет назад

    Great video! thank you so much for sharing this info.

  • @Thebowzer221
    @Thebowzer221 10 лет назад

    I am in Florida, so freezing is not an issue. Thanks 4 replying to my question. I will check You Tube. Thanks again.

  • @r.c.850
    @r.c.850 4 года назад

    WOW !! .... inventors are amazing !!!

  • @mikemaben7485
    @mikemaben7485 Год назад

    Great video to the point no advertisement crap. Vary helpful thx

  • @lostinfflood
    @lostinfflood 9 лет назад

    This is a great video. It is explained so well it gives me the confidence to attempt this job myself. Great job.

    • @HomeRepairTutor
      @HomeRepairTutor  9 лет назад

      Thanks dave mcc - I think you'll really like the SharkBites. Keep me posted.

  • @rikenglebert7558
    @rikenglebert7558 3 года назад

    Great video! Thank you!

  • @Thebowzer221
    @Thebowzer221 10 лет назад

    Thanks Jeff, I learned somthing today. I'm old school, torch and solder. This looks good , also I'm glad to see no leaking. I need to learn about Pecks piping. I want to run Pecks tube from my water meter (in the lawn) to my home, all under ground. Any videos on this type of work?

  • @HomeRepairTutor
    @HomeRepairTutor  10 лет назад +2

    Thanks Richard, I hope it helped you with your own project :)

  • @anthonyhernandez1553
    @anthonyhernandez1553 4 года назад +9

    OMG!!! THANK YOU YOUNG MAN! I LEARNED SO MUCH FROM YOU WITHIN 10 MINUTES, INTO MY BREAK TIME. THANKS GOD BLESS YOU! MERRY CHRISTMAS!

    • @HomeRepairTutor
      @HomeRepairTutor  4 года назад

      thank you!

    • @HomeRepairTutor
      @HomeRepairTutor  4 года назад

      just remember to debur your copper and properly set the fittings to the correct depth.

    • @freddyhouse8807
      @freddyhouse8807 4 года назад

      Wow I'm glad I seen this video cause I'm in prosses of doing this kitchen plumbing thank-you very much for this video.

  • @TDHobbies
    @TDHobbies 10 лет назад +3

    Too bad I didn't see this video earlier! I just replace a valve and actually removed some clamps holding the main pipe to move the pipe so I could accommodate a compression valve. I know it's not good to add stress on the main line. Thanks for the video.

  • @rodimus371
    @rodimus371 7 лет назад

    Good stuff thanks bro

  • @1967onebob
    @1967onebob 4 года назад

    Awesome video!

  • @Oldrbutnowisr
    @Oldrbutnowisr 5 лет назад +7

    well was a little skeptical because I always "sweated" my connections but after talking with some knowledgeable folks I bought a sharkbite shut off valve for a 1/2 in line. So being skeptical I had buckets at ready in case of a leak. I shut off the main water valve then went and turned on faucets to drain the lines as much as possible ( hint I left the lines open so gravity would drain them when I cut the line to install the valve) . I used a tubing cutter because having no burr on the end you are going to put the sharkbite on is vital to proper fitment and sealing - - I had a small splash of water come out but really it was next to nothing. One other step I should point out I used a fine emory cloth sandpaper and cleaned a good 2 inches of copper in the area I was going to cut because just like soldering a joint you want the area as clean as possible. I also used the emory after I made the cut specifically on the cut edge to make sure there were no burrs. I put a 1 inch mark on the line for a guide as to how deep the sharkbite fitting should go to seat properly and pushed it in place. Again being a skeptic I left a bucket there just in case and then went upstairs to shut all the faucets. I went back downstairs and turned the main valve on with eyes fixed on the new shut off valve and not one drop of water dripped. This line I'm installing the shut off on is for my water heater that died and the old valve on it didn't work so I couldn't drain it to remove it - - the heater had been in the house since at least the late 70s so I can't complain about it finally giving up the ghost in 2018 ( an old stone lined 80 gal tank). I mention that because today's water heaters have a fairly close standard for hook up lines but that old one had the cold in at the bottom of the tank so I have some line work to do. One other caution any time you shut off your main be sure to run all the faucets because when the pressure is forced through drained lines accumulated dirt/debris will be dislodged so run them to make sure you get a clean flow. Remember to pull your pants up when working on water lines and bending over - - "plumber's crack" needs to be eradicated - - good luck with your DIYs

    • @jacksagrafsky4936
      @jacksagrafsky4936 3 года назад

      2021 and I am doing the same thing as shown in the video and because the valve was installed in 1995. There is discolorations of the copper as well as a "label" that I would have to remove. I was going to use emery tape and sand the pipe. But was afraid of the scratches that would be left and would cause for a poor gasket or "O' ring seal. So I tried some very fine steel wool and it shined up the copper and removed the label and any glue. It also left the pipe smooth.

  • @PK_Diaspora
    @PK_Diaspora 6 лет назад +2

    Thank you! Excellent video. One of the best videos on plumbing. You explained it very well.

  • @ryanjerome2591
    @ryanjerome2591 5 месяцев назад +1

    H2P !!! - great video sir

  • @xChromerSatanasx
    @xChromerSatanasx 5 лет назад

    Great video

  • @mikem3742
    @mikem3742 6 лет назад +1

    This works great thanks

    • @HomeRepairTutor
      @HomeRepairTutor  6 лет назад

      one of my favorite methods for fixing exposed pipes, hope the tips help

  • @jamesdickson3616
    @jamesdickson3616 6 лет назад

    Pretty neat I like these fittings

    • @Gantzz321
      @Gantzz321 6 лет назад

      there is reasons that this product has been around but not used for many years, its shit.

  • @izzylogan25
    @izzylogan25 9 лет назад

    Really helpful video. thank you.

  • @Gadman
    @Gadman 11 лет назад

    Thanks a bunch. You just saved me from changing my piping to PVC.

  • @TARWERG
    @TARWERG 4 года назад

    That was cool who ever came out with this shark bite is a genius

  • @HomeRepairTutor
    @HomeRepairTutor  10 лет назад

    Hey Reagan,
    Thanks for that tip. Copper is crazy expensive. Plus, nobody to my knowledge breaks into houses to steal plastic-LOL.

  • @bingobongo445
    @bingobongo445 10 лет назад +10

    I live in an 1892 house,and have replaced about 95% of the plumbing in my home,with PVC drain and CPVC water lines.All CPVC lines are connected with SharkBite push fit connectors,and not one leak in 10 years. I am very happy with the SharkBite products. The Only thing i don't like is that there expensive.

    • @gthomas15229
      @gthomas15229 6 лет назад +3

      bingobongo445 It is pricey but much less than plumbers and great for those of us who never learned soldering of copper pipe. My problem now is that my hands have arthritis and I don't have strength in them.

  • @HomeRepairTutor
    @HomeRepairTutor  11 лет назад

    I've used SharkBites for the last few years and haven't had any issues with leaks. They're really reliable and it several rental homes we have here in Pittsburgh. Hope that answers you question ;)

  • @gthomas15229
    @gthomas15229 6 лет назад +1

    I like the Pittsburgh Panthers trim. I live in the North Hills School district.

  • @devinjaundoo1135
    @devinjaundoo1135 5 лет назад

    If I wanted to install a shut off ball valve for my main water line, right after the meter, would the shut off valve work alone by putting it between the the cut copper pipe? Or do I also have to get a sleeve?

  • @perecarl12
    @perecarl12 3 года назад +3

    Thank you for the video. FYI: You could have saved the extra work and materials by only using the "Slip Ball Valve" (#152).

  • @HomeRepairTutor
    @HomeRepairTutor  11 лет назад

    Awesome John, that's a huge bummer about your hot water tank :(
    It's cool that you didn't lose all your house water and can flush toilets. Water is both a blessing and liability at times!!

  • @MrElPoderozo1
    @MrElPoderozo1 3 года назад +1

    This was 8 years ago, have you had any problems with the sharkbite? Thanks for the video 👍🏽.

  • @stevezartman7238
    @stevezartman7238 7 лет назад +29

    Great video but I have a question about your process as I am going to be doing the same thing in my basement. Why did you cut off such a large section of the copper. I was just planing on cutting as close to the ends of the ball valve so the sharkbite fitting would go in place and click in.

    • @hearnjack
      @hearnjack 5 лет назад +2

      He didn't think he'd be able to reconnect without adding more pipe. I guess.

    • @sunrise8263
      @sunrise8263 3 года назад +2

      When replacing a "middle" section, whether with more pipe or with a valve, at least one connection requires the "slip coupling", so enough room is needed for it, as well as the one-inch insertion on each end of the slip coupling.

  • @HomeRepairTutor
    @HomeRepairTutor  11 лет назад +5

    I've been using SharkBites for several years and haven't had a leak yet.
    SharkBites are very dependable. Just make sure you push the fitting into the pipe by 1 inch and test for leaks.
    You'll be very pleased and if you need extra help just visit the SharkBite website

    • @12robjones
      @12robjones 3 года назад +1

      Amanda Laschola just tell me what does not fail “eventually “

  • @staceyprice1830
    @staceyprice1830 6 лет назад

    You are the MAN!!!! I almost gave up because I couldnt figure out to slide fitting on.... I did it!!!!!

    • @HomeRepairTutor
      @HomeRepairTutor  6 лет назад

      awesome, glad the video helped. What kind of repair were you doing?

    • @staceyprice1830
      @staceyprice1830 6 лет назад

      Cold water supply line to bathroom sink with pinhole leak!

    • @HomeRepairTutor
      @HomeRepairTutor  6 лет назад

      ugh, the worst. Glad you were able to fix it. Once it's learned the process is very simple. Great job

    • @staceyprice1830
      @staceyprice1830 6 лет назад +1

      Thank you! You clearly explained how to use slip... it really made the difference. Thanks again!!

  • @zedac0sta
    @zedac0sta 10 лет назад

    I just used Sharkbite fittings for the first time today and it was super easy. Works like you would expect it too.
    The fittings, in my case an angled 1/2 x 3/8 shutoff valve, spin. Can be annoying but how often do you need to touch your fitting?
    10/10 for me.

    • @HomeRepairTutor
      @HomeRepairTutor  10 лет назад

      Thanks zedac0sta - the spinning is one aspect that is indeed annoying. But like you said, how often do we tough the fittings and it doesn't matter in most cases. Glad you found the video helpful.

  • @malachy1847
    @malachy1847 11 лет назад

    Great Video........ as you were using copper you are allowed to pull out the internal support inserts in the sharkbite fittings, as these are in there to support CPVC and Pex piping..doesn't really make a difference just a slightly reduced flow because of these sleeves

  • @sundberg39
    @sundberg39 10 лет назад

    Thanks Jeff, Very useful information

  • @pierrebecquey8374
    @pierrebecquey8374 9 лет назад +1

    Great video. Had a frozen pipe burst this afternoon. Was able to use the slip end fitting to replace the cracked section of pipe. Will need to replace a bit of insulation and patch up the wall I had to cut, but thankfully I was able to access the pipe from the garage so that repair won't need to be as pretty as my new pipe section. (Got the fitting at Lowe's for a few bucks.Pro-Line brand.)

    • @HomeRepairTutor
      @HomeRepairTutor  9 лет назад

      Sorry to hear about your frozen pipe Pierre Becquey - good job fixing it yourself. I think slip on fittings are good for pipes you can access. Especially if you're in a hurry and don't have soldering supplies on hand. Thanks for letting me know about your successful pipe repair :D

    • @hillelsims
      @hillelsims 9 лет назад +1

      Hi, I have been using sharkbites for several years now, and they are great in a simple fix situation. I wouldn't use them for a main water shut off like some one else mentioned, but still fantastic for a homeowner who likes to tackle things them selves. My concern for Pierre Becquey, one day I couldn't get what I needed at Homedepot, where sharkbites are sold, and went to Lowes to buy their alternative product. I found the Lowes product did not work nearly as well as the Sharkbites. They are larger, harder to attach and did not make a good seal. I promptly returned the Lowes equivalent and bought a Sharkbite fitting. I don't know if anything has changed since that was a few years ago, but I would stick with Sharkbite. I terms of push fit fittings, they are the name brand and anything else you are taking a chance with.

    • @HomeRepairTutor
      @HomeRepairTutor  9 лет назад

      Thanks Hillel Sims for sharing your experience, it's good to know that SharkBites are still working well for you, too. They're a great option for any DIYer :D

  • @iananthony2578
    @iananthony2578 9 месяцев назад

    Will this work with a vertical cold water pipe to hot water heater

  • @reddred6969
    @reddred6969 10 лет назад

    Thanks I am going to help my sister save some $$$$

  • @HomeRepairTutor
    @HomeRepairTutor  11 лет назад

    Thanks for mentioning this, I totally forgot to add in a "Thought Bubble" to explain it.

  • @sku32956
    @sku32956 4 года назад +1

    I always replace old shut off valves when doing plumbing near it .

  • @xcross8537
    @xcross8537 4 года назад

    Awesome 😎

  • @hvoso6251
    @hvoso6251 9 лет назад

    super system, you can remove the sharkbite to add additional lines for laundry, baths, etc. The spinning everyone panics about is a plus not negative, it spins since it is easy to remove and connect other branch lines.

    • @HomeRepairTutor
      @HomeRepairTutor  9 лет назад

      Thanks h voso - I agree with you. SharkBites are pretty cool. Of course there's nothing wrong with soldered joints but sometimes this is a bit simpler for open walls.

  • @danielscarazzo5437
    @danielscarazzo5437 3 года назад

    Do you measure the distance between the two fittings to get the length of your copper pipe ?

  • @JR-kk6ce
    @JR-kk6ce 2 года назад +1

    It's been 10 years since this video. I wonder if it is still watertight.

  • @philmor1776
    @philmor1776 8 лет назад

    What's the minimum Cut (gap) a little over 6" I presume since the valve is about 3" long (and sets back 1”) and the slip coupler is about 4" long, and if so why so much gap , wouldn't 7” do?

  • @HomeRepairTutor
    @HomeRepairTutor  11 лет назад

    Hey Nelson, the best action you can take is to probably order it via Amazon.

  • @user-jh4bw6hd9r
    @user-jh4bw6hd9r Год назад

    What about the ground wire.. will the connectors need to be bonded to the ground ?

  • @noicing
    @noicing 3 года назад

    Dont you have to deburr the copper pipe first? I am asking because some videos say that you have to. Also, do I need to remove the little plastic sleeve inside the Shark Bite Fitting first as I am not using it with PEK ? I am not sure if I will even get a reply since this thread is 7 years old it seems.

  • @bigiron383
    @bigiron383 10 лет назад

    That slip in fitting is just what I'm looking for. Now to find some place that sells them here in Phoenix.

    • @vapemcvaperson
      @vapemcvaperson Год назад

      Did you find them, and are they holding up brah?

    • @davriley1
      @davriley1 5 месяцев назад

      hmmmmm. Amazon comes in handy now and then.

  • @btccoins5514
    @btccoins5514 4 года назад +30

    You need to DEBURR the copper pipe before you install sharkbite, if you don't do that, there is a chance that it might fail

    • @MrJimmy-ox7fq
      @MrJimmy-ox7fq 3 года назад +1

      You are correct....btc coins.....that was a critical missed step in this video. Excellent point made. Thank you for your observation and comment.

    • @natetraff
      @natetraff Год назад

      As long as the pipe cutting tool is sharp theres no need

  • @jonienglish3231
    @jonienglish3231 4 года назад

    Good Video
    Question ?
    did you have to Remove the inserts inside the Shark Bite Fitting ?
    i think they are there for use on Plastic Pipe for Reienforcement .
    Question 2?
    do you have to Chamfer the Pipe after Cutting ?

    • @skipwilliams7288
      @skipwilliams7288 4 года назад +2

      You are correct about the removal of the plastic insert for copper pipe. It's used mainly for
      pex pipe to keep it rigid. I installed a shower mixer today from copper to pex and removed the plastic insert for the copper side...No leaks

  • @HomeRepairTutor
    @HomeRepairTutor  11 лет назад

    Glad the video helped you out. Let me know how it goes :)

  • @davriley1
    @davriley1 5 месяцев назад

    Son was remodeling the bathroom in his house..... on Christmas evening no less .... accidentally cracked the 1/2" copper pipe coming up from the floor to the toilet. water started spraying everywhere. Looked for the shut-off valve to the house. yeah, right., crawled under the house to look for a shut-off valve. none to be seen. called the emergency utility number. poor utility lady came out in the middle of her Christmas dinner to help locate the shut-off main at the street, of course buried under 5" of built-up sod - but eventually found it and turned it off. Bathroom floor area was soaking wet -- luckily it was being remodeled! Put some fans in to help circulate the air and dry off the subfloor. 1-1/2" of water in the crawlspace under the leaking area! Came out with soaking muddy pants and back to the house for our Christmas dinner. Water is shut off -- for now. Leak is stopped -- for now. And how was YOUR Christmas??
    Long story short: Going to add a ball valve shut-off to the water main in the crawlspace!! Did not really want to do it "old school" and have to worry about draining the water pipes from the main and the copper pipes from the bathroom to solder the joint(s).
    I have used Sharkbite connectors in the past and was quite pleased with them. So I looked on RUclips and found this video. Precise and to the point! Went to the hardware store today and got a 1/2" Sharkbite Max Push-to-Connect End Stop to plug the broken 1/2" copper pipe - after cutting a clean cut and deburring it, of course!! (not going to use that line anymore anyway. Will properly remove this line down the road. So for now, simply capped it). No need to worry about removing the insulation, draining the water out of the pipes, fluxing it, and blow-torching the floor beams by accident! Also got a 3/4" SharkBite Ball Valve and Slip Coupling to add a shut-off valve at the main line into the house - in similar fashion shown in this video. (While the water is still shut off). Great to have these options available.
    Lesson learned: NEVER attempt projects on a holiday!!
    P.S. I read about the possibility of "losing" a possible ground through the copper pipes if I add the ball valve and will probably add a copper wire bridge between the copper pipes.

  • @occaligirl714mia
    @occaligirl714mia 9 лет назад +1

    after all this time, how good are those sharkbites working? thanks. good video

    • @HomeRepairTutor
      @HomeRepairTutor  9 лет назад +2

      Maria Alvarez thanks for you question because it's a good one. They're perfect. I've been using SharkBites for 4 years with no leaks. Of course you'll want to check if your local code allows them but I'm convinced they're a great option.

  • @tyliful
    @tyliful 2 года назад

    why do you need to install a slip end fitting? can the copper pipe be connected right onto the end of the valve?

  • @captkhaos1
    @captkhaos1 7 лет назад +4

    According to Sharkbite's own video you used the PEX fitting (mustard colored end). For copper you need to use the fittings with the black ends.

    • @andyhank9105
      @andyhank9105 6 лет назад

      I wondered about using pex vs copper attachments too... no answer?

    • @justrandom1145
      @justrandom1145 6 лет назад +1

      this can be used on copper, the plastic inside needs to be removed only if using copper and left inside for pex

    • @arcadion448
      @arcadion448 5 лет назад

      Tan colored can be used with a variety, copper and pex are among the two.

  • @ronaldzeoli7528
    @ronaldzeoli7528 4 года назад +3

    Remind people to clean the burrs on the ends of all the pipe peaces
    You have cut to ensure that the snake bites will work properly

  • @HomeRepairTutor
    @HomeRepairTutor  11 лет назад

    Yah, the price is almost twice at much for a Shark Bite versus a traditional shutoff valve but if you can DIY it you'll save more on the labor side

  • @jamaalaziz9910
    @jamaalaziz9910 3 года назад +1

    Did you have to cut copper pipe off? Could you have just cut out other valve at the ends and placed sharkbite in between without adding new piece of coppet?

  • @HomeRepairTutor
    @HomeRepairTutor  10 лет назад

    You bet Sundberg, hope it helps you out :)

  • @mrdev5281
    @mrdev5281 5 лет назад

    HarryKnows i think his single unit would have been even better just cut much closer to the old shut off and replace with the 1 shark bite. now sure why he had to cut so far from the valve but maybe he will comment. Ive used them and they hold well even over time, what i didnt know is they now come with a valve. Thumbs Up!

  • @robertheinkel7579
    @robertheinkel7579 3 года назад

    Shark bite makes slip joint valves only need to buy one piece . They are great

  • @hushmouthbeatz3231
    @hushmouthbeatz3231 6 лет назад +1

    Does it have to be the same size as the pipe or half inch or so bigger?

    • @HomeRepairTutor
      @HomeRepairTutor  6 лет назад +1

      Good question Brandon. SharkBite fittings come in 1/2”, 3/4”, etc. If you have 1/2” pipes get the 1/2” SharkBite fittings

  • @AnubhavShah
    @AnubhavShah 4 года назад +1

    there is another youtube video by this oldhouse on replacing a valve that i think may arguably be simpler.

  • @laxplaya25
    @laxplaya25 9 лет назад

    Hi, great video! Did you take the little plastic piece out of the Sharkbite fitting before putting the copper pipe in?

    • @HomeRepairTutor
      @HomeRepairTutor  9 лет назад +2

      laxplaya25 I called SharkBite and asked them about this. They said you can leave it in for any pipe :D

    • @laxplaya25
      @laxplaya25 9 лет назад

      Awesome thanks a lot!

  • @bobhaddock957
    @bobhaddock957 9 лет назад +1

    you WILL have to use the splice like in this video if you are putting the shut off in existing system / retrofitting. the plumbing that is already existing is already cut and soldered in place and there is usually NO room to spread the pipes far enough apart to put the shut off in. therefore you will have to cut the pipe further up or down and put the splice in. only way to do it using the "sharkbite" (name brand) fittings.
    Homedepot and Lowes have these fittings. one carries "sharkbite" fittings and the other carries the fittings under a different "name brand" all the same FYI

  • @Hear2Help
    @Hear2Help 7 лет назад

    how do you know what the gap is, and how do you know if your one inch lines will line up on the slip fitting, on the valve I understand, one inch easy, but how did you know the length of pipe to cut to get it to work one inch on both sides of the slip fitting?

    • @HomeRepairTutor
      @HomeRepairTutor  7 лет назад

      +Bob Long place another line on the pipe that's sliding into the slip fitting so that as you adjust the pipe you'll know it can't or shouldn't go beyond that line. And if you have to you can add a metal strap on the slip fitting to give it support. The strap would attach to the subfloor or a joist 👍

  • @ChiNguyen-wf1qt
    @ChiNguyen-wf1qt 3 года назад

    You don't debur the section of the copper pipe that you cut?? These sharp can it damage the o ring in the sharkbite

  • @JasonTylerRicci
    @JasonTylerRicci 7 лет назад

    These fitting types are revolutionizing the plumbing industry. Now, plumbers must stock various assortments of these SharkBite fittings in their trucks.

    • @HomeRepairTutor
      @HomeRepairTutor  7 лет назад +1

      there are a ton of different options now, I like SharkBites but it's still good to learn how to solder. Although PEX is a great option as well.

  • @dm19609721
    @dm19609721 8 лет назад

    Great video. One thing people should know is if you were to remove the shark bite fittings say a year from now, they are not to be reused. There is a rubber gasket inside that may get damaged from repeated removals. I also has to remove one shark bite fitting that was 4 years old and had a heck of a time removing it.

    • @staxoffunk1863
      @staxoffunk1863 8 лет назад

      +Dennis M does the rubber wear out if you dont remove it? I want do this to some old round handled shut offs that are stripped but I do not want to have to replace every few years? Also i need to add a new shut off to my main and am wondering if these shar bites will hold up?

    • @dm19609721
      @dm19609721 8 лет назад

      +Mike Carrington ........I am old school, I never had a sweated joint fail. My father re-pipped his entire house in 1972 and I sold it when he died in 2011 and never had any leak issues. I would only use a shark bite fitting if the pipe was easily accessible (not behind walls) and the cost of replacing it was not a concern.

    • @dm19609721
      @dm19609721 8 лет назад

      +Mike Carrington The rubber does not wear out but it can dry out over time. As I said mine was only 4 years old and it was really hard for me to get off. I've worked on cars all my life and rubber fitting eventually dry out and that is a fact......if you don't believe me take few elastic bands and put them in a drawer for 3 years.....then see how brittle they are. Shark bite has been around for maybe 10 years and perhaps they will last but they are not infallible. I've never seen a sweat joint fail unless it froze or sustained a hard blow to it. I remember reading the fitting are not to be reused....

    • @dm19609721
      @dm19609721 8 лет назад

      +Mike Carrington If you insist on using shark bites my only suggestion is use a fine emery cloth and sand the pipe. Like solder you need a clean joint....sand till its a nice smooth finish and remover any old solder that is on there if it exists.

  • @gereral1_jackofalltrades
    @gereral1_jackofalltrades 3 года назад

    I had main shutoff valve leak in crawl space. I bought ball shutoff sharkbyte valve to threaded end. Added a adapter brass to hose end . Used hose clamps once the hose was pressed into the brass barbed fitting and the fitting screwed into the other side on ball valve. Used plumpers thread tape. . The value is above ground flush with the water regulator. The sharkbyte valve does not touch the ground! . The old valve was 80 percent blocked because previous owner used copper and iron fitting. Always use brass on copper. Not metal on copper. 3 years later still holding. It's in dirt area under crawl space near foundation where it's not going to cause water damage if it leaks. I should get plumber to replace shutoff valve with a soldered one. I have to go under crawl space twice a year to shut off outside spout in winter to prevent freezing and turn it on in spring. I always check the ball valve for any leaks. To be safe I might install a small lcd camera pointing at it to check it randomly. I have to pay for water by usage so a slow leak can cost $$$. I even shut my water main off did the work and turned back on. When it was leaking it was scary as this valve was the last valve to town outside shutoff valve embedded in my lawn. I built a tool and made a video how to shutoff your water if you have those small blue ones with narrow access port on your lawn. I made tool so I dont have to wait for town to show up if this sharkbyte valve blows out. I can shut valve off right away. When they put in new hot water heater they use these fittings on the pipe at top water heater. I would not use these inside walls. Only where you can visually see them. If ball valve leaks it will leak into the ground. Not my floor boards, walls. So damage would be minimal.

  • @beversl2
    @beversl2 7 лет назад +1

    I just did a similar repair using the shark bites. I am a little weary of this system. Has it held up so far?

    • @renesilva241
      @renesilva241 7 лет назад

      Barry Evers I used it 5 years ago to run lines for a washer machine. so far no problems at all.

    • @vapemcvaperson
      @vapemcvaperson Год назад

      @@renesilva241 How bout now?