Sorry bro, the app doesn't show new comments then I forget. I have a video showing how I fit it and what you need first. Ships be one of my mods videos, of you can't find it I'll post you the link
My brkther I've bought a forkstem mount from quad lock but I need to remove the middle fork stem nut. Will that yoke nut be compatible with a quad lock mount for my phone??? Let me know please
Aqeel Teela Ali it’s not the yoke but that needs to be compatible. The cbr600 1mm yoke nut just allows you to plug things into it. Send me a photo of the quad lock kit which fits in the stem, message on Instagram buddy.
+Evan JJ (NTFSTYLE) hey thanks man, finally someone showing some acknowledgement. Hahaha. The clutch bite on the CBR was really far, the adjustable levers were just £16 and I put it in 1 so its really close range now which helps me keep a good hold on the handlebar for better control.
Holy fuck I was looking into buying these levers for my 16' CBR125R was sketched out whether to yolo it or not, defo doing it now as I know they fit! Cheers!
Cheers man, glad you enjoyed and found this useful. If its advertised for the cbr125 2012-2016 it should be fine, brake is very easy where as the clutch needs some fiddling. You doing much to your bike?
Cheers for the advice. I've had it a few weeks and got plans for it. The plan includes; clutch/brake levers, clutch/brake guards, exhaust and ram mount. So far I've prioritised the stuff which so far is just tank protector and crash protectors (£130 :o). But I mainly spent my leftover money on gear. Gotta have them full leathers :P
Haha yeah I got leathers, make sure you're has pockets. I made that mistake haha. The RAM Mount is easy to do, I've linked Motonosity's video on how to install. Exhausts, there are loads, as for the guards and crash protectors, if you unbolt the bar ends, be ready for a headache, you need a heat gun because they use glue, when you put them back in, Dont tighten it hard, you'll notice the throttle is stiff so find the right point and use the special bar end glue. Not sure if you knew, thought I'd mention it.
I couldn't resist the repsol leathers ;) luckily it has one pocket, enough for a phone and my debit card ;D. I only ever wear them for going on a ride with mates, other than that commuting is done in my kevlar jeans and textile jacket! Yea, the RAM mount I'm a bit sketched out by undoing the yoke nut, dunno if I want to. I don't really need my phone there tbf haha. The crash protectors were easy to do, had to drill a hole through the fairing which was sad but they look nice now! Well the bar end shit sounds like a pain in the ass, might not do them now. They looked so promising as they're only like £15 on ebay! I would love to do it but don't want to ruin the throttle control. Might just put the money from the lever protectors into the RAM mount then haha. Will defo get the levers tomorrow, how long was delivery on them? I see they're from Hong Kong lol...
Tom Rushforth yeah they took maybe 2-3 weeks I dunno, could've been a bit more. I'm not doing anything any more because I got my A licence and kinda want a 600 as a secondary because the bike dunks fuel like an alcoholic compared to the 125. As for the bar ends, RUclips it. I'd like to see the bike with the frame protectors if you got instagram.
its maybe a little late but do you think that that is the same centre nut as on the newer cbr 125 models (2011-2017) because i want to buy one but im not sure haha nice video :)
Here’s an example, should be able to find cheaper but you need something like these unless you get a whole adaptor kit so you can fit bobbins rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.co.uk%2Fulk%2Fitm%2F400971817017
There's a screen (bolt) that wedges it inside the fork. Its a hex head. Not easy to rip out. But the x-grip someone can just untwist it unless you change it to a bolt instead of a thumb screw.
When doing the levers, did you need to hold the nut underneath with a spanner? Watched another video and some other guy used a spanner to hold the nut otherwise it was spinning
That's a question for you to answer, if it spins, then yes, if not then no xD but make sure it's tightened well, don't over tighten, if the lever is stiff then loosen a little and check it a week or a month later to make sure it didn't get loose because mine on my cbr600rr got loose after 2 years xD
So wait because I want a ram mount i need to buy this yoke nut thing which costs 25gbp on ebay so it will fit the mount..?? What's the diffrence between the 600 one and the 125 one?
I tried finding one for 125 but couldn't. This one I paid maybe £13 (GBP) off eBay. Check the listing and if they've relisted it (probably relisted 30 times)
www.ebay.com/sch/i.html?_from=R40&_sacat=0&_nkw=cbr600rr+yoke+nut&_sop=15 Its even more than 25 gbp for me... Is that good? beside this there is no other sultion?
On the cbr125 you could get a bracket that bolts to your clip on (handle bar) you can check out or ask AshBandicoot and let him know I sent you. I'm sure there is. Let me check on ebay
AlcatrazMeow OK I think its 24 x1.00 yoke nut. I searched "yoke but 24 x 1.00" and loads came up for under £15. I'm sure that's what I used. I was using adjustable spanner (wrench) and didn't feel solid but could be my wrench. When you tighten be careful in case its a cheap piece of crap but for me, no issues so far man. And check how much to tighten as you have head set bearing. Let me know how it.goes bro
Well I checked and the seller you've bought from does not ship to my country so ive found others can you please tell me if those are the same as yours so I wont make a mistake www.ebay.com/itm/Dado-canotto-Ergal-Yoke-Stem-Nut-EXTREME-HONDA-CBR-600-R-RR-Oro-DC05-/121899634961?hash=item1c61c8d111:g:S1UAAOSw~OVWxy3C www.ebay.co.uk/itm/JMP-Pro-Bolt-Steering-Stem-Yoke-Nut-24-x-1-00-mm-Red-For-Honda-CBR-600-RR-ABS-/131785218081?hash=item1eaf02d821:g:cFUAAOSw3mpXFLHF They both say in the description 24x1 so just want to be sure thanks again man
Don’t remove the nut, you mean the silver one in the middle which I replaced with the red one? Feel free to screenshot and send message on Instagram. Don’t remove nuts without replacing haha
@@zaccouca6806 yeah get a replacement. My one was m24 x 1.00 mm yoke nut. Check what yours is and get a hollow one. But I’d suggest a Quad Lock. Much better!!!
ok I think finding a complete listing for it will be difficult, but here are the 2 parts, this is the stem, I have a video talking about it and Motonosity has a video on installing it. Should check him out.
Dennis Chong hey man. all I can say is check the specs, I THINK mine is 25x1mm not sure. you can always buy it, try it by hand and if it doesn't work just send it back, you'll lose like 20-40p for a stamp to return so not a major problem. I'll try get back to you tonight after I check out the specs of mine and your bike. if I forget try message me on instagram
Dennis Chong just had a look now and can't find anything, mine was m24x1.00mm, there's a link in the description for this video, it's ended but you can see the specs and if he's relisted it then try it
hey buddy, i do believe it is M24 x 1mm there is this in black www.ebay.co.uk/itm/303889708082?epid=652178699&hash=item46c13cf432:g:VWoAAOSwoTlgLTbS or this silver one also another gold one www.ebay.co.uk/itm/402696713958?epid=650339956&hash=item5dc29836e6:g:XS8AAOSwB6JgLSp5
on ebay the cluch lever looks very different on the black part and on the break lever there is a difference too so i don't know if its juste the picture in ebay or the wrong product :/ (i'm french sry if it's not very understandable i do what i can :D)
robinou57 I dunno, generally if you give bad feedback or message them, they give refund. It says its for the cbr125 so if its not, contact eBay and they'll fix it
If you want to fit it like this then yes, because the original yoke nut is not hollow, so you can't fit it through. If you do have a bike and the yoke nut is hollow then you don't need to get another one.
I would highly advised against it. You don’t want to look down at your arm, those bands may slip down to your wrist or fall off. I’ve tried that on a bicycle. The mount is in front so you just look down a little and not take your eyes off from what’s in front. Also if you need to stop to check something it’s gonna get annoying trying to get it off your arm and back on. Also with the helmet it will be a struggle and if it’s on your forearm...just still no..
heat stanly blade first it helps
Andrew Lewis for the ram Mount? gonna pin this comment to help anyone else who watches this comment. cheers pal
Honestly that top yoke nut has just made my day I have been trying to find that top yoke nut for agesssssss your amazing 😂
Thank you buddy! Glad it's helping people!
I LOVE YOU. i have been searching for months how to get the ram mount on my cbr 125 and nothing now i found this beauty love it thank you man
that was the main point of this video. cheers
Appreciate the video my man.....got myself a CBR600 yoke nut, ram nut kit and Xgrip on order.....👏
Great stuff mate! Hope the install goes well!
Great vid, I've got the exact same levers and rim tape, was just figuring out how to install a ram mount haha
Sorry bro, the app doesn't show new comments then I forget. I have a video showing how I fit it and what you need first. Ships be one of my mods videos, of you can't find it I'll post you the link
My brkther I've bought a forkstem mount from quad lock but I need to remove the middle fork stem nut. Will that yoke nut be compatible with a quad lock mount for my phone??? Let me know please
My cbr is a 2014 model and the nut I have is stock
Aqeel Teela Ali it’s not the yoke but that needs to be compatible. The cbr600 1mm yoke nut just allows you to plug things into it. Send me a photo of the quad lock kit which fits in the stem, message on Instagram buddy.
Thanks for the solution man I'm getting a Cbr 125 aswell and was wondering how the hell am I gonna attach the ram mount!
+Evan JJ (NTFSTYLE) hey thanks man, finally someone showing some acknowledgement. Hahaha. The clutch bite on the CBR was really far, the adjustable levers were just £16 and I put it in 1 so its really close range now which helps me keep a good hold on the handlebar for better control.
What grease did you used for levers?
Just multiPurpose, nothing fancy. They're easy to take off and grease again if I need to.
@@ArabianRider Thx man! :*
Holy fuck I was looking into buying these levers for my 16' CBR125R was sketched out whether to yolo it or not, defo doing it now as I know they fit! Cheers!
Cheers man, glad you enjoyed and found this useful.
If its advertised for the cbr125 2012-2016 it should be fine, brake is very easy where as the clutch needs some fiddling. You doing much to your bike?
Cheers for the advice. I've had it a few weeks and got plans for it. The plan includes; clutch/brake levers, clutch/brake guards, exhaust and ram mount. So far I've prioritised the stuff which so far is just tank protector and crash protectors (£130 :o). But I mainly spent my leftover money on gear. Gotta have them full leathers :P
Haha yeah I got leathers, make sure you're has pockets. I made that mistake haha. The RAM Mount is easy to do, I've linked Motonosity's video on how to install. Exhausts, there are loads, as for the guards and crash protectors, if you unbolt the bar ends, be ready for a headache, you need a heat gun because they use glue, when you put them back in, Dont tighten it hard, you'll notice the throttle is stiff so find the right point and use the special bar end glue. Not sure if you knew, thought I'd mention it.
I couldn't resist the repsol leathers ;) luckily it has one pocket, enough for a phone and my debit card ;D. I only ever wear them for going on a ride with mates, other than that commuting is done in my kevlar jeans and textile jacket! Yea, the RAM mount I'm a bit sketched out by undoing the yoke nut, dunno if I want to. I don't really need my phone there tbf haha. The crash protectors were easy to do, had to drill a hole through the fairing which was sad but they look nice now! Well the bar end shit sounds like a pain in the ass, might not do them now. They looked so promising as they're only like £15 on ebay! I would love to do it but don't want to ruin the throttle control. Might just put the money from the lever protectors into the RAM mount then haha. Will defo get the levers tomorrow, how long was delivery on them? I see they're from Hong Kong lol...
Tom Rushforth yeah they took maybe 2-3 weeks I dunno, could've been a bit more. I'm not doing anything any more because I got my A licence and kinda want a 600 as a secondary because the bike dunks fuel like an alcoholic compared to the 125. As for the bar ends, RUclips it. I'd like to see the bike with the frame protectors if you got instagram.
its maybe a little late but do you think that that is the same centre nut as on the newer cbr 125 models (2011-2017)
because i want to buy one but im not sure haha nice video :)
Mine is 2013. So hopefully. Think the spec was on the ad. I know other people bought it and it fit. If not just return it.
Does the stearibg stem nut need to be a specific torque?
Excuse me mate I’m just wondering what paddock stand do you use I can’t find one to fit the cbr 125r
Here’s an example, should be able to find cheaper but you need something like these unless you get a whole adaptor kit so you can fit bobbins
rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.co.uk%2Fulk%2Fitm%2F400971817017
Hey man, did you had rev limter on your motorcycle? mine is locked at 115km/h
that sounds about ride, it's a 125 xD max i got was maybe 75mph only a little bit more because it was down on an underpass
what? I can easily get mine to 130km/80mph on flat and once got it to 150km/93mph with a little downhill in a tunnel (took forever, but still)
Another and final question, how much is the ram mount stealable?
Thanks mate!
AlcatrazMeow as in how likely is it to be stolen? no idea, I always take it off
You just pull it off? No need for a screw?
There's a screen (bolt) that wedges it inside the fork. Its a hex head. Not easy to rip out. But the x-grip someone can just untwist it unless you change it to a bolt instead of a thumb screw.
I see. Thanks alot man. Going to order it soon. Subbed to your channel as well, good vids.
AlcatrazMeow thanks man lol always happy to help
When doing the levers, did you need to hold the nut underneath with a spanner? Watched another video and some other guy used a spanner to hold the nut otherwise it was spinning
That's a question for you to answer, if it spins, then yes, if not then no xD but make sure it's tightened well, don't over tighten, if the lever is stiff then loosen a little and check it a week or a month later to make sure it didn't get loose because mine on my cbr600rr got loose after 2 years xD
ArabianRider sweet bro. Was asking bc I gotta buy the tools, I don't have a massive tool set.
So wait because I want a ram mount i need to buy this yoke nut thing which costs 25gbp on ebay so it will fit the mount..??
What's the diffrence between the 600 one and the 125 one?
I tried finding one for 125 but couldn't. This one I paid maybe £13 (GBP) off eBay. Check the listing and if they've relisted it (probably relisted 30 times)
www.ebay.com/sch/i.html?_from=R40&_sacat=0&_nkw=cbr600rr+yoke+nut&_sop=15
Its even more than 25 gbp for me...
Is that good?
beside this there is no other sultion?
On the cbr125 you could get a bracket that bolts to your clip on (handle bar) you can check out or ask AshBandicoot and let him know I sent you. I'm sure there is. Let me check on ebay
AlcatrazMeow OK I think its 24 x1.00 yoke nut. I searched "yoke but 24 x 1.00" and loads came up for under £15. I'm sure that's what I used. I was using adjustable spanner (wrench) and didn't feel solid but could be my wrench. When you tighten be careful in case its a cheap piece of crap but for me, no issues so far man. And check how much to tighten as you have head set bearing. Let me know how it.goes bro
Well I checked and the seller you've bought from does not ship to my country so ive found others can you please tell me if those are the same as yours so I wont make a mistake
www.ebay.com/itm/Dado-canotto-Ergal-Yoke-Stem-Nut-EXTREME-HONDA-CBR-600-R-RR-Oro-DC05-/121899634961?hash=item1c61c8d111:g:S1UAAOSw~OVWxy3C
www.ebay.co.uk/itm/JMP-Pro-Bolt-Steering-Stem-Yoke-Nut-24-x-1-00-mm-Red-For-Honda-CBR-600-RR-ABS-/131785218081?hash=item1eaf02d821:g:cFUAAOSw3mpXFLHF
They both say in the description 24x1 so just want to be sure
thanks again man
So thetop yoke you attached is the yzf one ?? Can you attach a cbr one please
No, the hollow yoke nut I use is a Honda cbr600. Nut is a 24mm with thread being 1mm.
JUst a quick question i have the same bike does it do any harm to remouve the fork thingy on top to leasve space to mount a èhone device
?
Don’t remove the nut, you mean the silver one in the middle which I replaced with the red one? Feel free to screenshot and send message on Instagram. Don’t remove nuts without replacing haha
@@ArabianRider I meant the silver thingy yeah
@@zaccouca6806 yeah get a replacement. My one was m24 x 1.00 mm yoke nut. Check what yours is and get a hollow one. But I’d suggest a Quad Lock. Much better!!!
@@ArabianRider ok thanks I'll check that out
Awesome solution for the ram mount haha. Just.... Is it possible to get a link for the Ram mount you bought as I cannot find the same one online haha
ok I think finding a complete listing for it will be difficult, but here are the 2 parts, this is the stem, I have a video talking about it and Motonosity has a video on installing it. Should check him out.
www.ebay.co.uk/itm/RAM-MOUNT-UNIVERSAL-MOTORCYCLE-FORK-STEM-MOUNT-WITH-1-BALL-CAMERA-PHONE-SAT-NAV/282668926127?hash=item41d06184af:g:YX8AAOSww1dZySoC
www.ebay.co.uk/itm/Ram-Mount-Universal-X-Grip-Smart-Phone-Holder-Ball-Base-Motorcycle-Motorbike/172932524395?hash=item284394e96b:g:xRoAAOSw~RVZ5hvS
Links are to be used as an example. Check description to find what you're looking for. I still have it in my CBR600rr in my current videos you can see
thank you very much
Hi, does the yoke nut works for 2007 CBR125R as well?
Dennis Chong hey man. all I can say is check the specs, I THINK mine is 25x1mm not sure. you can always buy it, try it by hand and if it doesn't work just send it back, you'll lose like 20-40p for a stamp to return so not a major problem. I'll try get back to you tonight after I check out the specs of mine and your bike. if I forget try message me on instagram
Aite, thx mate ;)
Dennis Chong just had a look now and can't find anything, mine was m24x1.00mm, there's a link in the description for this video, it's ended but you can see the specs and if he's relisted it then try it
I can’t find the link for the yolk but can you tell me please
hey buddy, i do believe it is M24 x 1mm there is this in black
www.ebay.co.uk/itm/303889708082?epid=652178699&hash=item46c13cf432:g:VWoAAOSwoTlgLTbS
or this silver one also another gold one
www.ebay.co.uk/itm/402696713958?epid=650339956&hash=item5dc29836e6:g:XS8AAOSwB6JgLSp5
"m24 x 1mm yoke nut for honda" into ebay you will see some
The picture on the link don't match with the look of the levers you used on the video is this normal ?
I'm not sure how, to me they look similar, It's been a long time since I made this or had the bike, what's the difference?
on ebay the cluch lever looks very different on the black part and on the break lever there is a difference too so i don't know if its juste the picture in ebay or the wrong product :/ (i'm french sry if it's not very
understandable i do what i can :D)
robinou57 I dunno, generally if you give bad feedback or message them, they give refund. It says its for the cbr125 so if its not, contact eBay and they'll fix it
Yes it's probably the best solution
is the yoke nut essantiel?
If you want to fit it like this then yes, because the original yoke nut is not hollow, so you can't fit it through. If you do have a bike and the yoke nut is hollow then you don't need to get another one.
I havent tried the ram mount yet, but i would maybe have tried to heat up the knife with a lighter or something
I'd say get a longer blade xD and if that doesn't then maybe heat up a bit yeah
best vid!!!
looks good :)
You dont really need a ram mount. Instead you can strap a satnav/ phone to your arm :)
I would highly advised against it. You don’t want to look down at your arm, those bands may slip down to your wrist or fall off. I’ve tried that on a bicycle. The mount is in front so you just look down a little and not take your eyes off from what’s in front. Also if you need to stop to check something it’s gonna get annoying trying to get it off your arm and back on. Also with the helmet it will be a struggle and if it’s on your forearm...just still no..