Honda POWER STEERING whining noise fix and eliminate the BUBBLES
HTML-код
- Опубликовано: 8 сен 2024
- Due to factors beyond the control of RB The Mechanic, it cannot guarantee against unauthorized modifications of this information. RB The Mechanic assumes no liability for property damages or injury incurred as a result of any of the information contained in this video. RB The Mechanic recommends to follow safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, chemicals, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of RB The Mechanic, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not RB The Mechanic.
RB The Mechanic. All rights reserved. Publication, reproduction or distribution of this or any video by any means whatsoever, including without limitation electronic transmission via internet or e-mail, or re-uploading existing videos & re-uploading such material on any website anywhere in the world, is strictly prohibited without the prior written consent of RB The Mechanic.
#powersttering #hondawhiningnoise #fixwhiningnoise #fixhondapowerstteringnoise #fixhondapowersteeringnoise #powerstteringbubbling #bubblingpowersteeringfluid #howtogetridofbubblefrompowersttering #powersttering #noise #hondaaccordpowersteering #powersteeringnoisefix
Thanks for replying back .I have taken it everywhere I know.I think I’m going to get the reservoir looked at.Guy I talked to said the filter gets stopped up.I noticed this morning had some fluid leaking from underneath reservoir.Fingers crossed hope that it.
Yeah mostly the tubes get hard and they not able to seal on contact
I’m hoping replacing the reservoir and tubes to it stops the noise.Ready to sell if it doesn’t fix it.
@@MarkBerry-fx7zp I never had a case with reserver maybe line leakin and it’s sipping down
Need to lift front end and turn steering wheel with engine off a couple times, that's how you get rid of air bubble. I don't have a floor jack or jack stands so gonna have a shop do it since I replaced the steering pump with a new one but still whines when cold.
That’s even better
Thank u I always appreciate your videos!!!!
Welcome!!!
Thanks for the info !
Welcome
Nicely done. Thanks fo that.
Yup thank you!!
You saved me time and money, thank you!
Welcome
I have air and changed the o rings. Still air. But the psp is leaking. Could the air come from psp itself? I will rebuild and change the seals/gaskets/o rings of the psp. I just want to know if the bubbles could possibly come from the psp
Yes it can cause air
You have other video, im try to torque tighten the two top bolts.
U can try but if they hard like rock they will not seal
is it possible for the pump to leak BECAUSE of a bad o ring ?
No not cuz of line o rings pump has its own seals fix what need to be fixed then see if there’s other leaks
My high pressure power steering hose was leaking so I got it replaced. The shop that I went to used non honda parts and fluid. Since then it's been making this whining noise while accelerating or turning. Will it damage the pump if I steer the wheel lock to lock to clear out the air? I cannot jack up the front of the car.
Don’t go lock it lock stop right about it before hit the end
I got a 04 acura tsx, after all, mine kept leaking from the top, i tightened again, but still leaks, did you use lock tight on the bolt?, i didnt want to over tight, noise did go away.
Just this video no I jus tighten it how ever if pipe r hardened it will not seal
Please provide suggestion, I have 2012 accord, When I turn extreme right or extreme left - 90 degree turn, I get sound of Chreee for a second and then while returning to mid position there is no sound, should I change those o-rings or just leave it if it's minimal noise when turning extreme right or left?, there are no bubbles or no noise as you've shown in video.
U might be forcing the pump to push further than it has to go and it can cause belt to squeak
Thank you bro
Welcome
Any advice on getting air out the power steering hose/pump or whatever yoi would call it. My car sometimes the steering wheel doesnt want to turn when im reversing in to a parkong spot and i noticed that when it strarts to do that the power steering hose makes a weird noise snd the power steering hose shakes. It happens from time to time. Someone told me i may have air in there somewhere but not sure how to get that to go away. Dont want to put money in it if its a quick fix
It self blended top of the fluid and check for leaks if u got bad o rings it might need fixing
@@RBTheMechanic ok I'll do that. Thanks
@@RBTheMechanic need advice so my hose was leaking it got token off to get changed but never did so put back on the old one but now it’s still super stiff I’ve tried the turning of the wheel to try to get air out and it jus whines super loud which I wasn’t sure if it’s supposed to do that so idk I just need some advice because even tho it was leaking it was still drivable as long as fluid was in
@@monaeeuniquee2534 did u check to see if n pump failed u can do by observing rpm change of pump makes pressure the pressure switch will tell ecm there’s load and bring rpm up
Was the wheel a lil stiff to turn prior to changing the o rings ?
Yes
Ive tried everything.the bubbles dont go away.changed pump recon pump no leaks.bubbles are still there
Possability the seals o rings letting air in
Checked that too sir.was all good@@RBTheMechanic
I have power steering fluid leaking on the reservoir and the cap is good. So it must be bad O rings?
Not sure could be spill usully I don’t see fluid leak on to reservor
I’ve had everything done replaced the pump changed the o rings and belt tensioner pulley .It still whines what next .Is air getting in somewhere?
@@MarkBerry-fx7zp is there any power steering fluid leaking? Maybe there is a leak in one of the tubes. Check the steering gearbox.
@@MarkBerry-fx7zp check for leaks it maybe sucking air from some where and check to see if the pipe connector to resorvar r hard that’s also an jssue
@@MarkBerry-fx7zpThe whining sound could also be from low and/or dirty transmission fluid. Get it drained and refilled.
ran out of gas idling after 1 hour. hitch hikes to gas station to get more gas. started car again and whining n bubbling still der. Ok will wait again n update
Yup update me
@@RBTheMechanic noise still der and bubbles. i tink mybe still have leak and sucking air into system. which line would be sucking air into system? The high pressure feeder line or the return line? Can u help?
@@yamatomusashi1412 did I replace the orings also if ur pump is leaking that’s one issue
What were the seals called? Like is there a specific name and can I get them at oreillys ?
U have to ask them for print seals for power steering lines low and high pressure connecting to ps pump
I tried replacing the o ring, the reservoir, the hose to the pump, and I STILL HAVE AIR IN SYSTEM!!
Is the hose hard? If it’s hard it will not seat and cause air in system check the whole system
Where did you get the seals
My local part store
I believe that’s a k series tho
Ok
WHAT IF THE PROBLEM PERSISTS?
Then it maybe sucking air sumwhere or have leak
J series ps pumps are natorious for doing that 😂 … the transmissions cvt suk too 🤦♂️ I seen somewhere that their cooling system was defective and that’s the reason y those transmissions go bad a lot of the time
Yeah
No need to bleed d fluid?
No it will bleed it self let it run for good 10-15 minutes
I cant find the o rings anywhere
Amazon
The Amazon o rings are not the correct size!😢
What exactly name parts?
The power steering pump o ring
Thanks i
Question tho I’m having this problem whining in the morning I have to fill it every morning it leak everywhere and it bubble up do yall think it’s the pump
Not sure without looking at it so check to see where it’s leaking from common areas are pump seals o-rings and return lines
So what I do is take a heat gun and warm up the pulley nut and it goes away so I ordered the rebuild seal kit.
Ok replace the pump I guess than rebuilt the whole thing unless u ordered the 2 o rings then just do that
@@RBTheMechanic so my next question is because heat expands the seal in question could I use some AT-205 reseal in the power steering to help swell the o ring or recondition it so it’s not flat and stop the air on cold start? I will do a rebuild on the pump or replace it entirely when I have the time. Just looking for your thoughts on that.
I just did the alternator on my son’s 99 mercury cougar 2.5 it was hell had to take off bunch of shit to get to it but had to take off upper p/s line coming from reservoir to p/s unit. Tiny bit of fluid came out got it all together NOW the p/s unit whines and has bubbles and I don’t get it wtf happened?
Check for air leaks
What if it doesn’t go away
Then u maybe have leak or it’s sucking in air from the o ring
which oring connection would be sucking air?? feed or return? tnk u
@@yamatomusashi1412 usully it’s suction
@@RBTheMechanic yes yes, suction. My bad. So which line is it, is it the line coming from reservoir that could suction air into system if oring bad? Tnk u.
@@yamatomusashi1412 the line fat line resorvar to pump
Very cool thanks a lot . Can you put in fluid if it’s empty and drive rite away? Or do I have to let it idle for 20 ?
I would let it idle
@@RBTheMechanic I appreciate that thank you 🙏🏼