One question I will ask if I ever catch a livestream ill ask but for now. what are, In Your Opinion (IYO) are the best hex or as old timers or USA people call(Ed) Allen head or Allen keys, what are the best that dont round out/off? I just got an induction coil hearer im going to use to try and temper after cutting off the rounded bit.
WOW! What an awesome build video! What an awesome resource for the novice builder as well! To have an experienced RC guy go through an entire build with them! Thanks for all you do for the community!
To make the front bumper install easier, I drilled out the 4 locations of the bulkhead screws allowing me to install the 2 rear bumper screws and nuts prior to installing the front bulkhead assembly. For someone who takes my RC’s down 100% after several runs to completely clean and check everything, I’m always looking for ways to make bad engineering designs easier to work with…
Dude, I thought I had a RC fetish 4 Cars, 3 helis, two drones and a boat ... But after seen your collection I feel like pauper ... Absolutely fab bro ... I'll get there when I'm big ... I'm still young only 54 ... So got plenty time ... And I live in the UK ... Stumbled across your vid by accident but I've subscribed non the less ... Like you attitude and your videos are cool and interesting ...
Manscaped was the worst trimmer I ever bought. Battery was totally dead within a few months of buying. Barely was able to even cut hair even when it was new. Terrible product. But hey great video nonetheless Kev keep up the good work 🤙
The droop screws are important on some vehicles. They limit the down travel and stop it before the shock shaft and piston bottom out and stop all the weight of the arm/wheel/tire etc which is not good. If the arm hit the chassis before the shock gets to its limit then you are correct in saying they don’t really do anything. But if the shock is the limiting factor, by all means use the droop screws and you won’t destroy or have leaky shocks.
Futaba is and always has been 25t spline. I think HiTech or Savox or Spectrum, maybe all 3 are 23t spline. JR servos used to be 24t, I used them back in the early 2000’s, they were the first nice servos I ever bought. For just under 100.00 bucks they had the best specs out there.
Also I think a good video idea would be to get a Tekno ET48 2.0 along with the M2C upgrades to see how well it stands up to bashing. Tekno rigs are already by far the most durable “race spec” kits you can buy so adding the M2C stuff would put it n anothe league. Having the ET48.3, ET48 2.0, EB48.4, EB48 2.1, SCT410.3, ET410.2 and EB410.2, and absolutely loving every single one, both because I can rip them competitively at the track plus bash the heck out of them, or when I want to do speed runs I just throw a 26t pinion, 6s battery, foams and a shaved rear wing on the EB48.4, which combined with the Tekin RX8/2650kv motor, it hits 100mph on the GPS. Surprisingly I can go through an entire 5000mah pack going back and forth in a giant parking lot and it never gets close to overheating either. I love the Tekin stuff. Every one of my bigger than 1/10 rigs has them, and the 1/10 stuff has mostly Hobbywing combos.
From Maine USA. love your channel absloite blast to watch you. And all your info is awesome. Plus a great all around attitude. Keep it up bud. !!!!!!@@@@@@!@
Does anyone know how to swap a chassis on a maverick quantum xt flux I’m stuck and very confused as to why I have unscrewd everything and it’s still not coming off
Don't mind us, we are average Americans, unfortunately unintentionally we don't understand Anything basically outside of our own state. So yeah, I love these 😊 cheers
Love the truck and billed Christmas was ok went to the salvation for food then me and my son who is 3 went home watched a movie and went to sleep I hope you had a beautiful Christmas god blesse you
That cheap alloy from M2C's simple garage 3-axis mill is untempered, my DU racing towers which are actually 7075-T6 and anodized required my drill press. Not to mention they are a much better 5-axis CNC fit and finish. Edit-we won't talk about the cost😉...
I’ve been here since the tank video with the xmax and big window you jumped the xmax out the second story window that’s when I found Kevin love the channel
@2:31:00 that unmentionable topic. If isle of Mann dont allow them, I wouldn't go. In USA, the areas that have them are very low crime. when law abiding people have them, no problem. plus, the idea of the right here was to protect yourself from the people in charge. oh, targets are fun, a lot more than you may think, very challenging. 1st one I got, it was so hard to hit the mark, I thought I got a defective one. yeah, got a feeling you'd not only excel at it, I think you'd love it.
That is Awesome ' Arrma Bigrock is one Crazy & Cooling looking RC Truck - My Kid's Hayden She's -Zac's 8 - Colin's 6 - Landon 4 - My Crew ( The Nutt -Bird's ) Iol ' , We Love watching You Blast !!! We' as a Family are into Having as much Fun as We can So' I bought a Traxxas E-evo 2 Years ago , although We don't get Crazy with it I take them to the park We' take turns an let it Ripp ... They Love it ... Keep Blasting Sig
"Whats the worst RC Car?" Team Associated MT 10 is a possible contender" paraphrasing. lolo Wow. It has its flaws, but "bang 4 the buck" MT 10 has made me smile on multiple occasions after upgrades. "2 each there own" I understand that is a matter of opinion. U r my favorite UK content creator. TY for your content. Sincere best wishes from Washington DC USA.
@kevintalbotrc You should take one of your Xmaxx’s or a UDR and do a build with either using all available parts from Vitavon to compare. Now days the Xmaxx can be nearly 100% swapped out to alloy and the UDR is close too now that he released a full 7075 chassis. I know it wouldn’t be best for bashing, but man, they would be sexy!!! Do it Kev!!!
Afternoon kev just watched the video you done around 1yr ago called (ToTal Carnage) I had the idea of using 10mm tight coil shocks horizontal both front & Back behind Bar shaped Bumpers so if it lands tail on it’ll bounce rather than crunch also what about using either tungsten carbide or better still chromium for the chassis Base plate 👍🏻
If you say, I believe 100% cause you don’t lie you never lied any of your videos and you do launch your RC at the skate park and all that man I know you do it because you got the money to do it and you got the parts to fix them so I don’t have to pop the piss in the window at the window so I’ll take care of my babies like what you’re doing. Now I’m bout to get the big rock 6S and it is small. And I wish I can upgrade it like what you’re doing now make it more thicker and better but I don’t have the extra money to do it so whoever gets this one is a lucky guy and I wish it was me because I am getting one of this month I’m getting the gray one the gun Whatever is called but the gun color whatever is called but they got the red end of the white ones though they all look sharp so it’s hard to choose so I picked the gray one but I used to have the 3S and I sold it and I wish I kept it but the one you’re doing now I wish I could upgrade it the one I’m getting so but that’s why I don’t jump on. I jump on maybe like one or 2 feet in the air but I don’t jump them at the skate park so whatever you’re doing to it it’s making it more stronger. I know that so I wish I had the money to upgrade them. I just two months ago went out and bought Sledge and I love it. It’s a very good vehicle very good vehicle.
My little brother asked me what would be the best rc car as like a first good car for like drifting in our neighborhood and I said the armma felony because I watch your videos and thats like my favorite car I've viewed on your Chanel
![Seungmin "그렇게, 천천히, 우리(As we are)" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/kAzmhLHePqU/mqdefault.jpg)
Win This Actual car raffall.com/350694/enter-raffle-to-win-m2c-full-modded-6s-big-rock-hosted-by-kevin-talbot
Kev what’s the link to the dewalt impact you use in most your builds? Thanks.
One question I will ask if I ever catch a livestream ill ask but for now. what are, In Your Opinion (IYO) are the best hex or as old timers or USA people call(Ed) Allen head or Allen keys, what are the best that dont round out/off? I just got an induction coil hearer im going to use to try and temper after cutting off the rounded bit.
Hey kev, could I please have upgrades for the Arrma Granite Voltage 2wd please and thank you
Hey kev me and my three year old boy have been out bashing our ftx tracers brushless Ned more power
You gotta bash to see of its trash 😆
WOW! What an awesome build video! What an awesome resource for the novice builder as well! To have an experienced RC guy go through an entire build with them! Thanks for all you do for the community!
The armma big rock my favorite truck of all r c's I love the looks of this truck❤❤❤
To make the front bumper install easier, I drilled out the 4 locations of the bulkhead screws allowing me to install the 2 rear bumper screws and nuts prior to installing the front bulkhead assembly. For someone who takes my RC’s down 100% after several runs to completely clean and check everything, I’m always looking for ways to make bad engineering designs easier to work with…
I absolutely love this truck I remember when the first 3s version a requested you to do a video on it.
I still have a br 3s myself. One of my favorite all around bashers for sure.
“Finish off with the rear end”……….thats what she said…….priceless kev!
Dude, I thought I had a RC fetish 4 Cars, 3 helis, two drones and a boat ... But after seen your collection I feel like pauper ... Absolutely fab bro ... I'll get there when I'm big ... I'm still young only 54 ... So got plenty time ... And I live in the UK ... Stumbled across your vid by accident but I've subscribed non the less ... Like you attitude and your videos are cool and interesting ...
What I loved about this video is the dammits and what the hells because that's me wrenching on my RC's. So relatable coming from the king of RC YT
I really enjoy your videos. Just getting back into rc after a few years and these help motivate me lol
Always go to your videos first to see how good an rc is before buying you show how much of a beating they take love the videos man
Manscaped was the worst trimmer I ever bought. Battery was totally dead within a few months of buying. Barely was able to even cut hair even when it was new. Terrible product. But hey great video nonetheless Kev keep up the good work 🤙
The droop screws are important on some vehicles. They limit the down travel and stop it before the shock shaft and piston bottom out and stop all the weight of the arm/wheel/tire etc which is not good. If the arm hit the chassis before the shock gets to its limit then you are correct in saying they don’t really do anything. But if the shock is the limiting factor, by all means use the droop screws and you won’t destroy or have leaky shocks.
Futaba is and always has been 25t spline. I think HiTech or Savox or Spectrum, maybe all 3 are 23t spline. JR servos used to be 24t, I used them back in the early 2000’s, they were the first nice servos I ever bought. For just under 100.00 bucks they had the best specs out there.
Also I think a good video idea would be to get a Tekno ET48 2.0 along with the M2C upgrades to see how well it stands up to bashing. Tekno rigs are already by far the most durable “race spec” kits you can buy so adding the M2C stuff would put it n anothe league. Having the ET48.3, ET48 2.0, EB48.4, EB48 2.1, SCT410.3, ET410.2 and EB410.2, and absolutely loving every single one, both because I can rip them competitively at the track plus bash the heck out of them, or when I want to do speed runs I just throw a 26t pinion, 6s battery, foams and a shaved rear wing on the EB48.4, which combined with the Tekin RX8/2650kv motor, it hits 100mph on the GPS. Surprisingly I can go through an entire 5000mah pack going back and forth in a giant parking lot and it never gets close to overheating either. I love the Tekin stuff. Every one of my bigger than 1/10 rigs has them, and the 1/10 stuff has mostly Hobbywing combos.
skydive instructor 👍👍👊🏻👊🏻 I have 326 jumps
Long time watching you help people out from I'm Joe from Hutchinson Kansas
Went to the race track and improved my PB with .5sec just by oil in front shocks. 😮
Doesn’t matter! It’s what you want to do! They will watch regardless 😉
Just built my first buggy last night and wow does it mean so much more to you when you build it step by step
Can I get a new ec car please❤
I am so happy you said that your viewers meen more to you than anything keep it up 🎉
How do you keep your slipper clutch to stop slipping once tightened ? Once I really give it the beans it starts slipping all over again..
Arrma fan boy here , love the videos kev , keep up the hard work
From Maine USA. love your channel absloite blast to watch you. And all your info is awesome. Plus a great all around attitude. Keep it up bud. !!!!!!@@@@@@!@
Does anyone know how to swap a chassis on a maverick quantum xt flux I’m stuck and very confused as to why I have unscrewd everything and it’s still not coming off
Don't mind us, we are average Americans, unfortunately unintentionally we don't understand Anything basically outside of our own state. So yeah, I love these 😊 cheers
Love the truck and billed Christmas was ok went to the salvation for food then me and my son who is 3 went home watched a movie and went to sleep I hope you had a beautiful Christmas god blesse you
That cheap alloy from M2C's simple garage 3-axis mill is untempered, my DU racing towers which are actually 7075-T6 and anodized required my drill press. Not to mention they are a much better 5-axis CNC fit and finish.
Edit-we won't talk about the cost😉...
Sounds nice !
Can you provide some facts showing the material properties of M2C vs DU racing?
I doubt it. They can't even spellcheck
@@Mechabjornis no but maybe Kimberly can hit them all in a vice with her purse 😝
agreed- M2C is way overrated.
I own a M2C chassis and adu . The adu is fancier and more enforced . I got it for a stretched kraton
I watch you much as possible this is my favorite show to watch on RUclips and I'm hearing you from Merced California
I see you do the same as me using a manget to help hold screws its a great method.
I hope one day I can buy one of the RC cars in Kevin's video. For now it doesn't seem possible.😫
Whatever you say, I do believe you though cause you do build a lot of RC and you do have a lot Rc so you know what you’re doing so keep it up
I’ve been here since the tank video with the xmax and big window you jumped the xmax out the second story window that’s when I found Kevin love the channel
my life right now is just W i have kevin talbolt and it is FRIDAY!
@2:31:00 that unmentionable topic. If isle of Mann dont allow them, I wouldn't go. In USA, the areas that have them are very low crime. when law abiding people have them, no problem. plus, the idea of the right here was to protect yourself from the people in charge.
oh, targets are fun, a lot more than you may think, very challenging. 1st one I got, it was so hard to hit the mark, I thought I got a defective one. yeah, got a feeling you'd not only excel at it, I think you'd love it.
Thanks for all the content this year kev
a 4x4 awd little trophy truck that does epic donuts XD
Love you videos man I’m new to the hobby over here in NY made a cool mud rig keep up the good work 🎉
I tried to get raffle for the free big rock but for some reason it won't let me sign in so how can I get in on the raffle
Niagara Falls Canada , we love you up here Kev.
Love the work you do. Sounds like a lot of money to make a durable rc truck though. Happy New year kev
Westgate Iowa, USA
Barbie Drift Car! Nitro would be even better if it fits
I got myself an XRT and Fiesta ST Rally and a Hobbywing Max10 w/2400kv motor. Love the XRT. Waiting for a couple upgrades to come in for the Fiesta.
Yes I like the way you put that truck together I would like to do the same I have two trucks of redcat..
That is Awesome ' Arrma Bigrock is one Crazy & Cooling looking RC Truck - My Kid's Hayden She's -Zac's 8 - Colin's 6 - Landon 4 - My Crew ( The Nutt -Bird's ) Iol ' , We Love watching You Blast !!! We' as a Family are into Having as much Fun as We can So' I bought a Traxxas E-evo 2 Years ago , although We don't get Crazy with it I take them to the park We' take turns an let it Ripp ... They Love it ... Keep Blasting Sig
New to the rc world but I give you credit because I learn more from u than I do in the u.s.yhank hou
Franklin, Oh. Really enjoy your videos.
"Whats the worst RC Car?" Team Associated MT 10 is a possible contender" paraphrasing. lolo Wow. It has its flaws, but "bang 4 the buck" MT 10 has made me smile on multiple occasions after upgrades. "2 each there own" I understand that is a matter of opinion. U r my favorite UK content creator. TY for your content. Sincere best wishes from Washington DC USA.
I just ordered a mjx hyper-go. I hope it is a good car.
Bro Toyan makes or made a BV8! I makes 4.29hp I seen on RCDriverOnline 💯💯 Would LOVE to see you work with it and do something super cool!😊
@kevintalbotrc You should take one of your Xmaxx’s or a UDR and do a build with either using all available parts from Vitavon to compare. Now days the Xmaxx can be nearly 100% swapped out to alloy and the UDR is close too now that he released a full 7075 chassis. I know it wouldn’t be best for bashing, but man, they would be sexy!!! Do it Kev!!!
just ordered the new kriton 6s exb can not wait and plan to order the new outcast 8s exb in the new year
Merry Christmas
Booooom!!!! Only took a split second.
ITZ CHRISTMAS EVERYDAY 🎄 😅
I have a Big Rock 6s , watching from Alabama
Afternoon kev just watched the video you done around 1yr ago called (ToTal Carnage) I had the idea of using 10mm tight coil shocks horizontal both front & Back behind Bar shaped Bumpers so if it lands tail on it’ll bounce rather than crunch also what about using either tungsten carbide or better still chromium for the chassis Base plate 👍🏻
Continue like that Kev your videos are insane!
I love we didn't have to wait for the box review first lmao 😂😂😂😂
My current favorite is my 8s mokraton i built almost 3 years ago
Do have help with your RC builds or most solo?
I wonder if that front bumper would fit on a Kraton
IM UR BIG FAN KEV BRILLIANT CAR I WANNA😢😂
Good morning everyone
Great content Kev 👍🏻 learning lots from you… thanks
The es. Problems was the first 6s ones cstching on glames like hell or burning out.
If you say, I believe 100% cause you don’t lie you never lied any of your videos and you do launch your RC at the skate park and all that man I know you do it because you got the money to do it and you got the parts to fix them so I don’t have to pop the piss in the window at the window so I’ll take care of my babies like what you’re doing. Now I’m bout to get the big rock 6S and it is small. And I wish I can upgrade it like what you’re doing now make it more thicker and better but I don’t have the extra money to do it so whoever gets this one is a lucky guy and I wish it was me because I am getting one of this month I’m getting the gray one the gun Whatever is called but the gun color whatever is called but they got the red end of the white ones though they all look sharp so it’s hard to choose so I picked the gray one but I used to have the 3S and I sold it and I wish I kept it but the one you’re doing now I wish I could upgrade it the one I’m getting so but that’s why I don’t jump on. I jump on maybe like one or 2 feet in the air but I don’t jump them at the skate park so whatever you’re doing to it it’s making it more stronger. I know that so I wish I had the money to upgrade them. I just two months ago went out and bought Sledge and I love it. It’s a very good vehicle very good vehicle.
prefer Arrma. don't need any better then my Big Rock 3s , durable, easy and cheap to repair and itscheaper than Traxxas,
I will play some rc car i want kevin rc car. ❤️👌🏻✌🏻👍🏻👍🏻👍🏻😄🇮🇳🇮🇳🇮🇳🇮🇳🇮🇳
Hey there Kevin. Doing a killer job!
😅😅 😊😊
You must have one of the biggest collections of rc cars and trucks in the world.
My little brother asked me what would be the best rc car as like a first good car for like drifting in our neighborhood and I said the armma felony because I watch your videos and thats like my favorite car I've viewed on your Chanel
How much additional for all that m2c beefcake stuff? As in total as built cost when you finished would be what??? Thx
I know you dont do much 3s stuff but i have a 3s granite and its very durable. Ide like to see a durability video on it!
I love these live streams 👍👍
let's hope we don't end up with.....
WHAT HAPPENED??
Large RC M1A1 tank.
Du bist gut mann fleißig
All the way from Florida Cocoa Florida Sunshine State
It’s hard to imagine living somewhere were you Can’t even hunt for food No guns is wrong anywhere
Watching from western Australia 😎
Don't forget to update the firmware that they've done for it as there was a problem with the esc
1/16 Erevo 12:18 12:20
Well In the Arrma and Traxxas Debate i say brand don't matter , thay both brake and thay both are a lot of fun bashing lol..
Barrow Alaska
San Francisco California William!
Nice truck Kev! Just curious are you going to do a video on the new kraton exb?
❤😂😢😮😅😊. ไฟแอดพ์.
I run the Losi 1/5 DBXL 2 stroke gas 4x4 truck ...
Been out with my three year old boy with ftx tracers kev great little cars but needs to be keved faster bigger batteries any suggestions plz
Got me a Traxxas XO-1 San Francisco
Georgia, USA
👍👍
1/16 Erevo
What size motor is in the bigrock
How fast will the RC car go?
Redcat Valkyrie mt version, nothing wrong with it, just trying to learn it
Waffle waffle waffle get that thing put together
Building a sonc modell AR Wing Pro and the full FPV set up to help me with keeping it in control, Im more of a drone pilot.
Your shoe's are pure nerd🎉