2006 Mazda 6 fuel pump replacement
HTML-код
- Опубликовано: 10 сен 2024
- Final tip - Before you claim the victory on install - leave the fuel pump area exposed, fill the tank full of gas, drive around, let it sit in drive way for a bit. Verify it's "bone dry" before reinstalling lid and back seat. btw - when I say "crescent wrench" - replace that with the word "rachet wrench"
Changing the fuel pump out on my 07 Mazda 6 and I appreciate this video because I didn’t know half of the tricks you described. Thanks much.
1 little tip that is absolutely magic for installing the plastic retaining ring, firstly clean it really well and make sure its completely dry then put it in the microwave in the center of the plate for 10 seconds each side then rush back to the fuel pump and it will spin on most of the way by hand and just use the tool to tighten it up
...I live in a flat!!😂
Great video on fuel pump removal for a 1st gen Mazda 6. However, note that the torque spec for the sealing ring is NOT 80 ft*lbs as he states. According to my workshop manual, the spec is 59 to 66 ft*lbs.
Thanks for making the video gonna save me a lot of head aches. Caught the shout out for Scotty kilmer
Thank you, it was a very detail explanation, great Job
Great vid, well done! Very informative!
To be honest with you, you don't really need the lock ring tool to tighten it, as hand tightening it as far as you can is enough, as the MRA is plastic and can crack if over tightened. The rubber seal will seal it if it is on properly and fairly tight. We change these all the time and what I have mentioned is all that is required. Good step by step Video though
Patrick Finau what's the secret to getting it to seat properly on that dann rubber ring?
Yeah, and makes it harder, to remove , when tightening with a tool, as I'm finding out 🙊
Giving the engine a attitude adjustment
How empty should the tank be?
@ericdebby not sure if you're still monitoring this youtube channel. But do you remember which fuel pump you bought?
I have a 2007 mazda i 4cyl that needs a fuel pump replacement and there are just too many choices with a wide range of price points. Amazon goes for as low as $90 while some car specific sites go for $450-800.
Do you know what the center bulge is on the fuel pump? Does it have to be exactly like it to fit in the mazda?
What happened to the part where you disconnect the fuel line?
Extremely well explained. Well done
Thank you. I couldn't figure out what was wrong with my car. I checked my spark plugs and their brand new. And I couldn't think of any other reason.
What's the part number I have 03mazda 6 3.0 and I have problems found the right fuel pump thanks...
Gotta say, no one has the correct way, for my Mazda 6 2010, to get the back seat up, as, it DOES NOT come out!!!
All these videos have been useless, for this, as mine has, BOLTS ON FLOOR, it then goes up on hinges, does not come out, at all, so much simpler and neater.
That was through a friend.
Is there a video were it's step by step how people do it because I have a Mazda 2004 wagon and I need to install a new sending unit.
If you have been having trouble with the airtex e8587m fuel pump getting seated you might want to cut the springs. The dual springs are stiffer then the stock single which makes the profile about an inch to tall. This forces you to compress the pump as was stated around 9:25
This is on the first gen mazda 6
Thanks dude. That was a helpful video
You have to buy the hole thing
All you can't get the fuel pump only instead by fuel pump
What is the name of that tool so I know what I’m looking for?
Fuel Pump Spanner Wrench
I just pulled one out with a small pry bar, and hammer. Worked just fine. Just takes a little finesse.
What is that top part called that screws off and on to hold fuelpump in place
anyone know where i can find the fuel pump wrench at? cant seem to find it. i have a toyota fuel pump wrench if theyre the same ?
Thank you for the greatest explanation! The instructions are so damn clear that I didn't even miss not showing actually process. My son is a capitalist so I gave a Galaxy watch for his labour in this 2 people tightening ;)
It makes sense to do this and fuel filter together. Where is the fuel filter located? TIA
Hello sir, thanks for this video. I have the same model car. My car runs, but has 280k miles and it is starting to stall a bit. i've replace plugs and wires and ignition pack last year. I can't find the fuel filter, can you tell me if the fuel filter is in the pump or tank or where. I get different messages when searching online. It's Sunday and I cant call my local Mazda dealership until tomorrow. thanks for your help if you see.
stjohn both in tank
Where did you purchase it?
Also before opening the fuel tank you might want to cut the excess whole a little wider if using the tool 2:40
Where can I find a fuel pump for a low price??? For a 2007 Mazda 6
Where.can.i.get.chap e.fule.pump.mazda.05
2007 honda fit how much gas does that save
What is that tool and where do I get one
“Mazda 6 fuel pump removal.” “…just watch the other videos for that part.”
That helps thank you
9:30 "a long metal pole" a leverage pipe or a pipe used with a ratchet to gain leverage
You remember where the rubber ring is in the installing process? Longs story short got a car without fuel pump installed
Should have filmed actually removing it
I got one for $50 on rock auto
Los rayaban el de la Taconaso
To much protocol
i don't get it