How to Replace Mazda 3 Fuel Pump Complete Assembly with Level Sender suit 2003-2007
HTML-код
- Опубликовано: 30 сен 2024
- In this video we demonstrate how Replace Mazda 3 Fuel Pump Complete Assembly with Level Sender suit 2003-2007
The whole job took roughly 1 Hour.
Product available here for $195.30 partsfactoryau...
Savings of up to $500
Southport Wreckers Online ( Used Engines) : southportwreck...
Subscribe and comment on this video for any video requests! Learn to be your own mechanic and save loads per year on maintenance costs!
Realest video ever, unscrewing that plate and realizing it’s not what you were expecting lol
I just cut a hole on top of the fuel tank. After 2 minutes, off you go.
And all they (Mazda) had to do was make the hole under the seat just a little bit bigger. Doubt that an extra 25mmm in the overall diameter would effect crash performance...
Agreed
What about using snips to enlarge the hole then bending back into place ? I doubt any structural weakness will result?
@@mickmouse5715 For sure that can be done, and many have done. But Mazda should have made the hole big enough in the first place.
@@mickmouse5715is there a tutorial on how to do this?
@@miniespeon158 cut. Bend.
Was so excited when you said half an hour 😂. My daughter's pump went today and trying to find someone now to change it. Look's like I'm gunna be busy.
This won’t work, you have to drop the entire tank and make sure you get the new fuel pump to seat properly. Also be aware to not hit the fuel send units little circuit board while installing cause it could bend causing it to not make proper contact in the best case scenario or worst case is break the circuit board all together which is why I had to replace mine initially and the one I bought after was broken as well. And dropping it isn’t that hard. Get the car about a foot and a half up remove the bracket, like he did in the video, remove the plug and fuel line to the fuel pump then all that is left holding it up are the two fuel hoses connected to tank itself and it’ll drop right down. The higher the car is lifted up the more difficult it will be to drop it, 1 1/2 up is perfect regardless of how much fuel is in the tank. I’m literally working on it right now. Dropped the tank twice. Make sure to throughly check the fuel pump when you buy it. That sending unit is what is to be aware of. Hope this helps anyone.
THANK YOU for sharing your wisdom with those of us who don't have the level of knowledge that you do. I REALLY APPRECIATE you!!!!
Many thanks. Your video is very clear
That Laugh was REAL PAIN
Definitely was.
I felt your pain when you said a short install time.
Be sure to diconnect hoses before nut. Thanks for your efforts
All the best neal sw fla usa
Thanks for the tips!
Question, is the acces or llocation of the fuel pump different in European vs American models and /or in different years? I volunteered to help a friend who can't afford to have it done in a shop. I just don't know if I need a lift or have the clearance from jack stands to drop the tank (if I have to) from the street
It's an 2013 mazda3, in the US
I'd say they are exact same
Thanks guys, your video helped me out a lot (2013 Mazda 3). It got me most of the way there. Unfortunately for me the ring seal was held in with phillips screws that I then stripped while attempting to remove them so I had to take out the tank completely.
Inside of mines dirty
I'm buying another fuel pump for my Mazda 3 2010 2.0 but the specs of the item say "Without Pressure Sensor" is that normal, is the sensor located somewhere else in the vehicle or is this fuel pump missing it?
That is just the fuel pump, the whole fuel module has the pump and sensor
Exactly what i was looking for 💪🏻 i was pumping gas today in my 2009 mazda 3 and seen gas leaking out the bottom🤧 about to replace mine this weekend myself
No problem 👍
Is this the same for the Mazdaspeed3 2008?
Yes should be very similar
Good video, thanks
Glad you liked it!
Thanks You
Welcome :)
Put alot of trust in that forklift.
9t forklift 1t car
@@thepartsfactory4239it ain't gonna hold 9t when the hydraulic lines and valves call it a day. I don't think you can put the mast on locks lmao
Air nibbler, enlarge hole in required direction, bend tab up. Replace pump, bend tab down, seal with foil backed sealing tape. Your personal fleet only. Never for a customer.
Lol! driving a car that needs a fuel pump so it runs out of gas.. fat chance mate. 😅
Sometimes its the Full Level Sender that needs replacing
I'm wondering why you said that wasn't the fuel pump under the backseat when it was ?
It is, but you can't access it.
@@thepartsfactory4239 I just did
@@mariobtron5907it’s a filter pump isn’t it? how did you access it from the seat you would have to cut the floor?
@@tonyjohnston9641 it's rhe fuel pump. It plugged right into it. Yes I cut the floor. I used a grinder and a wet towel. It worked.
@@mariobtron5907Did you make a new panel to put back over the hole, my fuel pump is going out in my 3. I am going to cut it as well and make a new panel to cover it I might just seal the new panel to the floor board with rtv.
Pay attention gentlemen aka guys.....