Tip for AM4 users: if you plan to install it without removing the motherboard, don’t unscrew both plastic holders all at once, if you do it will drop your backplate and you will have to remove the motherboard and put the backplate on before able to install the plastic+metal screws from the new cooler.
I am thankful that RUclips tutorials have increased and improved so much since the last time I built workstations. I stopped, rewound, and continued step by step through this video and it made installing my Deepcool AK620 SO much easier, both in understanding each function and comprehending how to install. Thank you so much, Mike!
Just installed this cooler as part of my first build and wow, I underestimated the amount of pressure needed to get those last two screws in! Kept turning the screwdriver and never feeling it "bite" because I was afraid to use too much pressure and risk breaking something. Rewatched this video a dozen times at the table while trying to figure out what I was doing wrong, haha. Thanks so much for this, it really helped me out.
I've built many PC's but was unfamiliar with this particular CPU Cooler. This video was so helpful and clear. Thank you so much for creating this and sharing. It made the process so simple and easy.
I remember feeling so proud the first time i mounted the cooler. Afterwards started building computers myself and never trusted someone else to do it for me.
You’re a hero. Installed this as my first ever non stock cooler from AMD and the prospect of it was stressing me out. Was struggling a bit while building but after watching this everything went smoothly and worked out great. Thank you so much for your content!
this one the most simple video YET very very very hekpful and detailed , ty so much for telling all about which side of screw to use + brackets etc etc some of this small details help a lot for ppl like me who have never done this before TY sir
My two cents from my build using this exact cooler, it's a good idea to plug your CPU cable from your PSU into your mobo before installing this cooler. I neglected to do this had an enormous amount of trouble getting my CPU power cable plugged into my mobo and instead of removing the cooler, I opted into buying a pair of needle nose plyers.
Hello, greetings from the Philippines. Just messaged a customer service support from DeepCool last week, and good news is that AK620 and AK620 WH versions are AM5 motherboard ready, since the AM4 bracket accessories are compatible for AM5 versions.
Really tempted to make a comment like “Really fantastic cool video” but done that before. So it was a Cool Fantastic video, thanks Mike. See you tonight.
Thank you, straight to the point with no guff. One thumb up. ps, you really want both fans blowing into both heatsinks. It is configurable, but won't be as good at cooling in the "suck" position.
I had huge problems when I came to attaching the cooler to the stand that we built up in the begging. The screws were to short and wouldn’t go down. Eventually I had to remove the bracket with the arrow and directly screw it on the fan and then attach it that way
@@skull7231haha I made this comment 2 months ago so excuse me if I get some information wrong. But when you watch the video you will notice that one of the small iron brackets have an arrow on them. These brackets are the ones that you install directly on the motherboard and from there on install the fan itself. However, for me the screws were too short so I had to install the brackets and everything directly on the fan (which I had not installed on the motherboard yet) and then from there on install the entire basis with the fan attached
@@volle.5982 How did you managed to to put the fans into the motherboard later with such a small space? Did you used a screwdriver or just tighten it with your fingers?
I found the connector would not reach down to the upwards screws due to the springs being ridiculously strong. I had to take off the retention flange at the bottom and remove the pin/spring/washer in order to squeeze the springs a couple of times with a monkey wrench so that they would spring sufficiently. Once I did that it fit just fine. Many curse words were utilized while I tried to work out this solution.
Hey I’m new to pc building, I installed the cooler just as you did in the video but noticed that you didn’t use an lga 1200 or 1700 Mount/bracket on the back of the motherboard. Do I need to remove everything and install this or will it be fine on its own?
Thanks a lot, man. No one says what to do if the fan interferes with the installation of memory, and you said that you can rearrange it in advance. I thought about it too but doubted if it would work well in this case! Thank you.
The white color variant just came out. Sigh, really wish it had come earlier to compliment with my white case. Still the cooler is fantastic. Well worth the money and pennies you paid for it.
I have a problem with the 2 mounting screws on the head sink. These are the 2 screws with the springs to provide proper tension between the heat sink and the CPU. the 2 screws do not move so the springs do not get compressed.
This is maybe easier to fix or at least advise if we can ask more questions and get direct answers, so feel free to join our Discord chat and we can go over it in more detail discord.gg/XtBTGQ6BDu Agree to the rules by clicking the emoji and you will get access to the rest of the Discord channels
thanks for this planning to buy it with my old b450 mortar max and too lazy to check dimensions u save me alot of time😂. have to put the fans on the rear side
I'm still debating if I should get this cooler for my 3950x. It is cooled by the Snowman mt-6, but when temps will get hotter, it may not be sufficient enough as it is a single tower. The 4 cores over the 5900x, also cooled by a mt-6, really make a diffference in heat output. As of now, the 5900x is still below the 90 degrees, but the 3950x stay close to the 90, sometime more or less by a few degrees. As per AMD, the max temp is 95 before the cpu start to protect itself and since the computer is stable, I'm not too worried. But with summer coming fast over here, that might be another story!
@@ninjatall15 I was always supposed to do it after enabling PBO, but I'm lazy and let it as it.. But I will probably do it later when the weather start to get hotter.
@@mikesunboxing yeah, but right now, the temps is 89C,which is acceptable for me. But I will take your suggestion if things start to deteriorate. Still impressed by the Snowman, especially that my 3950x is not a silicon lotery winner... 🙄
What Temps are you getting with this set up while under load? I think mine runs a bit hot. FFXV high 70s Farcry 5 Low 80s Last of us part one shader compiling 90c Horizon zero dawn low 60s Case temp avg around 28c to 34c Tower is mid size Two huge intake fans at the front. 1 smaller exhaust fan at the back and 2 smaller exhaust fan at the top.
Thank you, i see on 2:06 in that the backerplate is what the screws and spacers go into. Thought that was the case, was factoring few mm of the circuit material
Hey mike, thanks for the great video. Had one question tho, my ram is 51mm and I wanted to know if I can put fans in a way that it wouldn't touch the ram? (One at rear and one at middle) Also I want the airflow to be from right to left of the case
This is maybe easier to fix or at least advise if we can ask more questions and get direct answers, so feel free to join our Discord chat and we can go over it in more detail discord.gg/XtBTGQ6BDu Agree to the rules by clicking the emoji and you will get access to the rest of the Discord channels
@@mikesunboxing well what about the 4060? Do u think waiting for the 4060 is a good idea because many tests showed that it is near the 3090 Performance and it only needs 200w. I hav a 600w bequiet PSU with an NZXT aio and ryzen 5 3600. the will 4060 Will cost 400-500$ it says. Will the Pins for the GPU Power connection be the same? Is it a good Idea to wait? Sry for my bad english
That defiantly is a large cooler. I really like the design of the fin stack. It's a bit overkill for my CPU's. My i5-4690k draws 88 watts. The rest max out at around 65 watts. Thanks for the review Mike and Lady Kath. Take care. Cheers
This is maybe easier to fix or at least advise if we can ask more questions and get direct answers, so feel free to join our Discord chat and we can go over it in more detail discord.gg/XtBTGQ6BDu Agree to the rules by clicking the emoji and you will get access to the rest of the Discord channels
This is maybe easier to fix or at least advise if we can ask more questions and get direct answers, so feel free to join our Discord chat and we can go over it in more detail discord.gg/XtBTGQ6BDu Agree to the rules by clicking the emoji and you will get access to the rest of the Discord channels
Threads supplied on screws provided do not work for my AMD MSI Motherboard. Close, but wrong threading. Cannot install because of wrong screws provided.
I purchased the Ak620 cooler, but when I attach the backplate to the main board, is it compatible with the backplate used by other air coolers? Can I go ahead and install the original backplate without removing the motherboard? The cooler I used was an rc410.
Hey! Is it possible to install this cooler in a Motherboard called A320 A pro MAX by msi? Was really thinking to buy one of these but im not sure if it will fit correctly.
Hello! I ordered this cooler with these components: GPU: Gygabite RTX 4070 192-bit 12GB Windforce OC CPU: Intel i7-13700K Motherboard: Gygabite Z790 UD AX RAM: Kingston Fury Beast DDR5 6000 mhz 2x16GB PSU: MSI MPG A850G 850W SSD: Samsung 990 PRO 1TB Case: Sharkoon TG6 RGB ATX Because this CPU cooler is so big and covers the RAM, I decided to buy the RAM without RGB lighting. Also my case has already 3 x 120 mm fan in front, 3 x 120 mm on top and one in the back. Those fans are RGB. Because of this I decided to buy all components without RGB and leave only the fans of the case to make the light. The GPU, of what I've seen, has only a little bit of lighting... It will look nice like this or do you consider it will be better to change before I get the components, to buy RGB RAM, the gaming version of the GPU which has cooler RGB, take out the 3 fans on the top of the case and put a liquid cooler. Please help!
@@mikesunboxing do you think is worth 165 more euros for a 4070 TI, instead of 4070? I play Fifa, GTA V, RDR 2, CS:GO, Forza Horizon. I'm upgrading from a GTX 1070. I found the Gygabite 4070 Gaming at 735 euros and the 4070 TI at 900 euros.
Hey, do you know where I can buy the spacers from? I removed mine and cannot find them anymore. Without a spacer I cannot mount the cooler on top of my cpu! :(
Thanks, subscribed. I got a question. My ambiance is 35 degree Celsius. After installing this I'm getting 55-60 on idle. And 70-75 while gaming. Is it too much or normal?
This is maybe easier to fix or at least advise if we can ask more questions and get direct answers, so feel free to join our Discord chat and we can go over it in more detail discord.gg/XtBTGQ6BDu Agree to the rules by clicking the emoji and you will get access to the rest of the Discord channels
why doesn't the DeepCool put an extra AM4 backplate in the packaging. I'm upgrading the cpu cooler that came with the used pc that i bought. and it doesn't have the backplate. so now i have to order one from amazon US and wait for international shipping which will take atleast 14 days for delivery. this sucks so bad
Why would they add a bracket when 99% of people already have one that comes with the motherboard, deepcool can’t be held responsible for the motherboard not being supplied with the mounting
I'm struggling with getting mine into my motherboard, I'm using a B660 plus WiFi d4 motherboard and for some reason brackets are to low for the cpu cooler to be installed? (I'm hoping I didn't damage the cpu or motherboard because at one point I put a lot of pressure to try and get it on)
This is maybe easier to fix or at least advise if we can ask more questions and get direct answers, so feel free to join our Discord chat and we can go over it in more detail discord.gg/gaeeDPw
I just needed a lga 1700 mount which I've asked the manufacturer to send just for an update. For a first time builder I could have damaged my motherboard trying to get the other mount on without realising but luckily I stopped myself from putting to much pressure on it
@@andrewpaul6364 glad to hear they are sending you one, i was confused but then realised the ak400 comes with LGA1700 mount but the AK620 at present doesn't
This is maybe easier to fix or at least advise if we can ask more questions and get direct answers, so feel free to join our Discord chat and we can go over it in more detail discord.gg/XtBTGQ6BDu Agree to the rules by clicking the emoji and you will get access to the rest of the Discord channels
@@mikesunboxing thought i'd give you a lil update. Got the 620, bit of a stinker getting it on but i managed lol Doesn't interfere with the ram, was worth it (:
I installed this cooler on my 7900x cpu and im getting high idle temps around 50°c, is this normal or should i repeat the installation process to see if i screwed up somewhere?
could be mounting pressure, but 7000 series is nuts for wattage and thermals unless limited in the bios to 65w and / or undervolted or curve optimiser negative 20 or 30
@@mikesunboxing I was that will deepcool ak620 cpu cooler fit on msi mag b550 tomahawk with rams having 4.4 cm of height without the need to set the front fan a little bit up
"Don't want to over-tighten it, when you feel a little resistance, stop." Meanwhile with the coolers using the plastic brackets the boards come with you have to literally sit on it to get it to snap in. So glad I didn't do that with mine, just feels shady, getting this cooler instead.
This is maybe easier to fix or at least advise if we can ask more questions and get direct answers, so feel free to join our Discord chat and we can go over it in more detail discord.gg/XtBTGQ6BDu Agree to the rules by clicking the emoji and you will get access to the rest of the Discord channels
Thanks!
thank you very much for the super thanks! much appreciated
Tip for AM4 users: if you plan to install it without removing the motherboard, don’t unscrew both plastic holders all at once, if you do it will drop your backplate and you will have to remove the motherboard and put the backplate on before able to install the plastic+metal screws from the new cooler.
massive massive tip
Just learned this the hard way
1:45 for people like me who have bad reading/listening comprehension skills XD
this is why im so glad i have a case where the back panel opens and i have access to the back of the mobo
and where you put the ram btw? this is so big it covers 3 of the ram slots legit you cannot put anything in it anymore wtf
I am thankful that RUclips tutorials have increased and improved so much since the last time I built workstations. I stopped, rewound, and continued step by step through this video and it made installing my Deepcool AK620 SO much easier, both in understanding each function and comprehending how to install. Thank you so much, Mike!
Great to hear! glad it helped
Just installed this cooler as part of my first build and wow, I underestimated the amount of pressure needed to get those last two screws in! Kept turning the screwdriver and never feeling it "bite" because I was afraid to use too much pressure and risk breaking something. Rewatched this video a dozen times at the table while trying to figure out what I was doing wrong, haha. Thanks so much for this, it really helped me out.
Bro same lmao
I've built many PC's but was unfamiliar with this particular CPU Cooler. This video was so helpful and clear. Thank you so much for creating this and sharing. It made the process so simple and easy.
Glad it helped!
and where you put the ram btw? this is so big it covers 3 of the ram slots legit you cannot put anything in it anymore wtf
I remember feeling so proud the first time i mounted the cooler. Afterwards started building computers myself and never trusted someone else to do it for me.
yeah i know what you mean there
Koje kuciste imas druze? Da li znas moze li stati u deepcool CL500?
@@Milos11160 CL500 165mm, AK620 160mm, može :D
@@SuperNapolitanka Nadam se da moze negde pise da je 160,163,165mm da ne bude knap..
@@Milos11160 Nema nista brate
You’re a hero. Installed this as my first ever non stock cooler from AMD and the prospect of it was stressing me out. Was struggling a bit while building but after watching this everything went smoothly and worked out great. Thank you so much for your content!
Glad I could help
Thank you Mike for making these upgrades so easy.
Glad you like them!
Thanks for showing the whole process. This is my first pc build and I've been stressing!
hope it all goes well
this one the most simple video YET very very very hekpful and detailed , ty so much for telling all about which side of screw to use + brackets etc etc some of this small details help a lot for ppl like me who have never done this before TY sir
thanks, glad it was helpful
Thank you so much for this. I haven’t built a PC in two decades. Everything seems so very much more complicated these days
Glad it helped!
Really love how u are detailed and patient been watching ur channel for few years now thx Mike
Thanks 🙏
My two cents from my build using this exact cooler, it's a good idea to plug your CPU cable from your PSU into your mobo before installing this cooler. I neglected to do this had an enormous amount of trouble getting my CPU power cable plugged into my mobo and instead of removing the cooler, I opted into buying a pair of needle nose plyers.
Thank you so much for uploading this. It made installation so much easier.
Glad it helped
absolutely helped with the installation thank you 😭🙏
Glad it helped!
That kewler is a bit of a beast !
it seems to be a good choice and performs really well. And for an RGB lover, i am actually really liking the more subtle styling.
Hello, greetings from the Philippines.
Just messaged a customer service support from DeepCool last week, and good news is that AK620 and AK620 WH versions are AM5 motherboard ready, since the AM4 bracket accessories are compatible for AM5 versions.
thanks for the info
@@mikesunboxing you're welcome. You're welcome to share this on your next video, and hoping for more MSI AM5 motherboards unboxing soon.
Really tempted to make a comment like “Really fantastic cool video” but done that before. So it was a Cool Fantastic video, thanks Mike. See you tonight.
thanks Paul, yep see you later for some tech fun and rambling
Exactly what I needed, very well explained, thank you !
Glad it helped!
Thats so easy to fit and looks the part. Much prefer this design than risk AIO water leaks. Thanks for sharing Mike and Kath👍
Our pleasure!
Thank you, straight to the point with no guff. One thumb up.
ps, you really want both fans blowing into both heatsinks. It is configurable, but won't be as good at cooling in the "suck" position.
I had huge problems when I came to attaching the cooler to the stand that we built up in the begging. The screws were to short and wouldn’t go down. Eventually I had to remove the bracket with the arrow and directly screw it on the fan and then attach it that way
Thank you so much for this, I also encountered this issue and thought I was the only one. Quite cumbersome issue haha
@@therealLOGS Haha yeah man. I hope everything turned out well at the end!
May you specify more? I don't understand what do you mean by arrow bracket
@@skull7231haha I made this comment 2 months ago so excuse me if I get some information wrong. But when you watch the video you will notice that one of the small iron brackets have an arrow on them. These brackets are the ones that you install directly on the motherboard and from there on install the fan itself. However, for me the screws were too short so I had to install the brackets and everything directly on the fan (which I had not installed on the motherboard yet) and then from there on install the entire basis with the fan attached
@@volle.5982 How did you managed to to put the fans into the motherboard later with such a small space? Did you used a screwdriver or just tighten it with your fingers?
I found the connector would not reach down to the upwards screws due to the springs being ridiculously strong. I had to take off the retention flange at the bottom and remove the pin/spring/washer in order to squeeze the springs a couple of times with a monkey wrench so that they would spring sufficiently. Once I did that it fit just fine. Many curse words were utilized while I tried to work out this solution.
I’ve definitely been uttering expletives trying to screw this damn thing in, so I’m gonna give your tip a go.
Had the same problem. I just squeezed the spring with a small pipe wrench. No need to take off anything from the screw
Terrible design, shouldn't need pliers to install a heatsink
@@bernieflanders how did you took off the retention thing?
Thanks Mike, I didn't realise you could do different configurations. I will redo my setup soon and place the fans better.
No worries!
looking at this as fed up with AIO failing waiting for a replacement Galahad AIO replacement due to failure!
Thanks Mike. It is on par with Scythe Fuma 2 and both have great aesthetics.
i think i prefer the AK620, the fuma is a bit large
@@mikesunboxing fuma 2 is great for builds that show rgb ram. Also it's compatible with some sff case.
Awesome vid... Just used this to upgrade from a stock amd fan to this deepcool fan
Thank you! This was very helpful
Glad it was helpful!
Subbed mate! Just bought this as my first aftermarket cooler and you made it really simple 😊
Thanks for the sub!
Nice one! Love me a sleek dual tower!
Me too!
Thank you so much for making this video. I'm not handy at all but with your video the installation was a breeze!! ❤
Glad it helped!
height is an issue on AM5 as it didn't fit my B650E Steel Legend. The cooler base contacts the CPU before the mounting screws make contact.
thanks for the heads up
Did you ever get it to work? I'm having this same exact issue and its driving me crazy lol
@@anthonycastellanos7088 i got it you just have to force it down a bit so the screw catches the shreds.
@@JayzBeerz bro i give up trying too pull down the screw in my B650M adus tuf
Available from affiliate links:
Amazon local: amzn.to/3udx6lh
Ebay UK: ebay.us/6ikfcE
Ebay US: ebay.us/RfwtgP
Ebay CA: ebay.us/fqAwmk
Ebay AUS: ebay.us/zlIJ0s
Hey I’m new to pc building, I installed the cooler just as you did in the video but noticed that you didn’t use an lga 1200 or 1700 Mount/bracket on the back of the motherboard. Do I need to remove everything and install this or will it be fine on its own?
this is for the AMD processors. if you are on intel then yes you should use the supplied backplate from deepcool
Thank you so much that was very clear and helpful ❤
Glad it was helpful!
Thanks a lot, man. No one says what to do if the fan interferes with the installation of memory, and you said that you can rearrange it in advance. I thought about it too but doubted if it would work well in this case! Thank you.
Clarification, who wants to do the same: you should save the direction of the fan in this case, otherwise they will blow towards each other!
Any news about the white version the AK620?
not that i know of sorry, i will ask my contact
@@mikesunboxing
ooh thats ok, i think i saw somewhere deepcool hinting the white version
'coming soon'
The white color variant just came out. Sigh, really wish it had come earlier to compliment with my white case. Still the cooler is fantastic. Well worth the money and pennies you paid for it.
@@afiq358 Thanks for letting us know
Review & How to is Worthy of Support comment & a Like 🙂
Thanks William :-)
@@lorderectus1849 But i'm not the new kid 😛
I have a problem with the 2 mounting screws on the head sink. These are the 2 screws with the springs to provide proper tension between the heat sink and the CPU. the 2 screws do not move so the springs do not get compressed.
This is maybe easier to fix or at least advise if we can ask more questions and get direct answers, so feel free to join our Discord chat and we can go over it in more detail discord.gg/XtBTGQ6BDu
Agree to the rules by clicking the emoji and you will get access to the rest of the Discord channels
Thanks Mike
cheers mr W
Olá Mike, sou brasileiro e seu tutorial foi muito útil para mim, muito obrigado!
Thanks! You helped a lot.
Mike! You rock! That was so straightforward and helpful! Big thanks man!
Glad it helped!
thanks for this planning to buy it with my old b450 mortar max and too lazy to check dimensions u save me alot of time😂. have to put the fans on the rear side
Glad I could help!
Thanks for the video.
Does it matter which direction the fan blows? Are they supposed to push out the back above the i/o panel?
Yes they should ideally be exhausting to the nearest outlet
Good guide,sir.
Thanks 🙏
Thank you man :)
I'm still debating if I should get this cooler for my 3950x. It is cooled by the Snowman mt-6, but when temps will get hotter, it may not be sufficient enough as it is a single tower. The 4 cores over the 5900x, also cooled by a mt-6, really make a diffference in heat output. As of now, the 5900x is still below the 90 degrees, but the 3950x stay close to the 90, sometime more or less by a few degrees. As per AMD, the max temp is 95 before the cpu start to protect itself and since the computer is stable, I'm not too worried. But with summer coming fast over here, that might be another story!
Try undervolt your 3950x
@@ninjatall15 I was always supposed to do it after enabling PBO, but I'm lazy and let it as it.. But I will probably do it later when the weather start to get hotter.
i would turn off PBO or set it to auto rather than enabled, that will reduce the temps a bit but not hurt performance in general
@@mikesunboxing yeah, but right now, the temps is 89C,which is acceptable for me. But I will take your suggestion if things start to deteriorate.
Still impressed by the Snowman, especially that my 3950x is not a silicon lotery winner... 🙄
Does the Deepcool AK620 work with AM5 motherboards? Is an additional install kit needed to make it work?
yes it comes with the fittings now
What Temps are you getting with this set up while under load?
I think mine runs a bit hot.
FFXV high 70s
Farcry 5 Low 80s
Last of us part one shader compiling 90c
Horizon zero dawn low 60s
Case temp avg around 28c to 34c
Tower is mid size
Two huge intake fans at the front. 1 smaller exhaust fan at the back and 2 smaller exhaust fan at the top.
does sound a bit on the warm side but you didn't mention what CPU you are using and the normal ambient temps in the room, so hard to say for sure.
What about the backer plate, OR
is that solid steel on the back of the B550 TOMAHAWK enough??
the stock amd one is fine
Thank you, i see on 2:06 in that the backerplate is what the screws and spacers go into. Thought that was the case, was factoring few mm of the circuit material
Bless you sir, thank you so much!!!
You're welcome!
Thanks for the clear explanation, gave me that final push to make the purchase 🙌
do you think it would cover both ram sticks if i was to put it in a mini itx build
i don't think so, there should be enough clearance
Thank you for this! Didnt realizw i had to MANHANDLE it 😂
No worries!
Hey mike, thanks for the great video.
Had one question tho, my ram is 51mm and I wanted to know if I can put fans in a way that it wouldn't touch the ram? (One at rear and one at middle)
Also I want the airflow to be from right to left of the case
Yes reverse the fans should be okay if the vrm heat sink isn’t too big
@@mikesunboxingby reverse, you mean a 180° turn?
@@KakaSiaz yes just invert or reverse them
Maaaan huge respect, you made my day
glad to help
My bracket doesn't protrude out of the board for the plastic riser screws to go on the board. No side bar about this issue or possible solution.. 😢
This is maybe easier to fix or at least advise if we can ask more questions and get direct answers, so feel free to join our Discord chat and we can go over it in more detail discord.gg/XtBTGQ6BDu
Agree to the rules by clicking the emoji and you will get access to the rest of the Discord channels
Where do you put the excess fan cable? Is it safe to wrap it around the base of the heatsink or will that get hot?
Should be fine
Great video.
Thanks!
Hi Mike. Whats ur Opinion on the RTX 3050 (380€) and the Rtx 3060
(450€). Cant decide which one to get
for the extra the 3060 for me
@@mikesunboxing well what about the 4060? Do u think waiting for the 4060 is a good idea because many tests showed that it is near the 3090
Performance and it only needs
200w. I hav a 600w bequiet PSU with an NZXT aio and ryzen 5 3600. the will 4060
Will cost 400-500$ it says. Will the Pins for the GPU Power connection be the same? Is it a good Idea to wait?
Sry for my bad english
That defiantly is a large cooler. I really like the design of the fin stack. It's a bit overkill for my CPU's. My i5-4690k draws 88 watts. The rest max out at around 65 watts. Thanks for the review Mike and Lady Kath. Take care. Cheers
yeah it is overkill for most systems to be fair, but it would keep it very cool
@@mikesunboxing I have two of the Vetroo V5's, one in black and one in white. Take care. Cheers
you're cool, thanks for help
thanks for watching
if we loosen the middle screw at 6:54 will the mounting pressure become more or less ?
it won't make any difference
For some reason my motherboards whole don’t fit the screws?
This is maybe easier to fix or at least advise if we can ask more questions and get direct answers, so feel free to join our Discord chat and we can go over it in more detail discord.gg/XtBTGQ6BDu
Agree to the rules by clicking the emoji and you will get access to the rest of the Discord channels
Same here!! Idk what to do or what the problem is 😭
I don’t have anything to screw it into? Like my back plate doesn’t have pieces to screw the front plates to
This is maybe easier to fix or at least advise if we can ask more questions and get direct answers, so feel free to join our Discord chat and we can go over it in more detail discord.gg/XtBTGQ6BDu
Agree to the rules by clicking the emoji and you will get access to the rest of the Discord channels
What if the AMD4 backplate is not there anymore, due to the new backplate was for my last cooler and is different.
you need to get one somehow
Threads supplied on screws provided do not work for my AMD MSI Motherboard. Close, but wrong threading. Cannot install because of wrong screws provided.
sorry to hear that. contact the seller or deepcool and they should sort that out for you
Спасибо ! всё предельно понятно.
I purchased the Ak620 cooler, but when I attach the backplate to the main board, is it compatible with the backplate used by other air coolers? Can I go ahead and install the original backplate without removing the motherboard? The cooler I used was an rc410.
It should
Hey! Is it possible to install this cooler in a Motherboard called A320 A pro MAX by msi? Was really thinking to buy one of these but im not sure if it will fit correctly.
yes should be fine
Hello! I ordered this cooler with these components:
GPU: Gygabite RTX 4070 192-bit 12GB Windforce OC
CPU: Intel i7-13700K
Motherboard: Gygabite Z790 UD AX
RAM: Kingston Fury Beast DDR5 6000 mhz 2x16GB
PSU: MSI MPG A850G 850W
SSD: Samsung 990 PRO 1TB
Case: Sharkoon TG6 RGB ATX
Because this CPU cooler is so big and covers the RAM, I decided to buy the RAM without RGB lighting.
Also my case has already 3 x 120 mm fan in front, 3 x 120 mm on top and one in the back. Those fans are RGB.
Because of this I decided to buy all components without RGB and leave only the fans of the case to make the light.
The GPU, of what I've seen, has only a little bit of lighting...
It will look nice like this or do you consider it will be better to change before I get the components, to buy RGB RAM, the gaming version of the GPU which has cooler RGB, take out the 3 fans on the top of the case and put a liquid cooler.
Please help!
you are on the point there with the cooler, it might be better to go with an AIO these chips get quite hot
@@mikesunboxing do you think is worth 165 more euros for a 4070 TI, instead of 4070?
I play Fifa, GTA V, RDR 2, CS:GO, Forza Horizon. I'm upgrading from a GTX 1070.
I found the Gygabite 4070 Gaming at 735 euros and the 4070 TI at 900 euros.
Hey, do you know where I can buy the spacers from? I removed mine and cannot find them anymore. Without a spacer I cannot mount the cooler on top of my cpu! :(
i would ask deepcool support most likely they will send them out to you
It fits inside a Gigabyte B650 AORUS ELITE AX ATX AM5 Motherboard? or its too big?
should be fine on there from what i can tell
Thanks, subscribed. I got a question. My ambiance is 35 degree Celsius. After installing this I'm getting 55-60 on idle. And 70-75 while gaming. Is it too much or normal?
sounds a little high but you didn't mention what CPU you have or chassis
@@mikesunboxing I'm using Cooler Master H500M case, 3700x ryzen cpu 1660 ti graphics card, 32 gb c16, 3600 hz ram.
@@iamsurajsharma 55-60C makes sense if your ambient is 35C also 70-75 is perfectly fun under load, just make sure it doesn’t go over 85C :)
@@kingfu987 Thanks for the advice. It's running great 👍.
I have mine sag a little bit. I am worried if i need to tighten the screw a little bit more.
Btw, I am using i5-12600k, LGA1700 motherboard
yeah check that everything is secure
How do you cable manage at the end?
This is maybe easier to fix or at least advise if we can ask more questions and get direct answers, so feel free to join our Discord chat and we can go over it in more detail discord.gg/XtBTGQ6BDu
Agree to the rules by clicking the emoji and you will get access to the rest of the Discord channels
why doesn't the DeepCool put an extra AM4 backplate in the packaging. I'm upgrading the cpu cooler that came with the used pc that i bought. and it doesn't have the backplate. so now i have to order one from amazon US and wait for international shipping which will take atleast 14 days for delivery. this sucks so bad
Why would they add a bracket when 99% of people already have one that comes with the motherboard, deepcool can’t be held responsible for the motherboard not being supplied with the mounting
@@mikesunboxing understandable. but sucks for the 1% like me. now i have to wait 14 days to get a backplate.
Thank you!
You're welcome!
Mint mate cheers
thanks for watching
I'm struggling with getting mine into my motherboard, I'm using a B660 plus WiFi d4 motherboard and for some reason brackets are to low for the cpu cooler to be installed? (I'm hoping I didn't damage the cpu or motherboard because at one point I put a lot of pressure to try and get it on)
This is maybe easier to fix or at least advise if we can ask more questions and get direct answers, so feel free to join our Discord chat and we can go over it in more detail discord.gg/gaeeDPw
I just needed a lga 1700 mount which I've asked the manufacturer to send just for an update. For a first time builder I could have damaged my motherboard trying to get the other mount on without realising but luckily I stopped myself from putting to much pressure on it
@@andrewpaul6364 glad to hear they are sending you one, i was confused but then realised the ak400 comes with LGA1700 mount but the AK620 at present doesn't
Not sure what I did wrong but there’s a bit of clearance between the bracket and cooler and I can’t screw it in :/
This is maybe easier to fix or at least advise if we can ask more questions and get direct answers, so feel free to join our Discord chat and we can go over it in more detail discord.gg/XtBTGQ6BDu
Agree to the rules by clicking the emoji and you will get access to the rest of the Discord channels
Спасибо большое! Если бы не вы, я бы весь вечер устанавливал бы данный куллер!
glad to help
I have four sticks of Corsair Vengeance ram, the short ones. Will this cooler clear them fine or will I have to remove a stick or two?
Also very nice video, I learn mostly by observation so the amount of detail is really helpful (:
i think you will be fine there with the low profile ram, depending on your needs and budget maybe also consider the AK400?
thanks that is very kind of you
@@mikesunboxing thought i'd give you a lil update. Got the 620, bit of a stinker getting it on but i managed lol
Doesn't interfere with the ram, was worth it (:
@@MisterDemonTC Glad you're happy with it :-) Thanks for the update
Can you damage the processor if you tighten the screws too much?
it is possible i guess for LGA sockets, AM4 would be okay
does it have enough clearance for g.skill trident z5 series RAMs?
not sure sorry
Will this same installation guide work for AMA 5.?
Yes it will be the same process just a little easier as the backplate is fixed in AM5
Thanks so much
I installed this cooler on my 7900x cpu and im getting high idle temps around 50°c, is this normal or should i repeat the installation process to see if i screwed up somewhere?
could be mounting pressure, but 7000 series is nuts for wattage and thermals unless limited in the bios to 65w and / or undervolted or curve optimiser negative 20 or 30
👍👍👍👍
Thanks for watching :-)
Will it fit with a ram having 4.4 cm clearance?
not sure what you mean there sorry
@@mikesunboxing I was that will deepcool ak620 cpu cooler fit on msi mag b550 tomahawk with rams having 4.4 cm of height without the need to set the front fan a little bit up
@@hamzagamer552 Did you try this in the end? The corsair vengeance I'm looking at has a clearence of 4.5cm / 45mm
One of my mounting screws are broken. It just doesnt click in
Might need to contact support or check your mounting hardware
"Don't want to over-tighten it, when you feel a little resistance, stop."
Meanwhile with the coolers using the plastic brackets the boards come with you have to literally sit on it to get it to snap in.
So glad I didn't do that with mine, just feels shady, getting this cooler instead.
What do you do for the am4 if you do not have the back plate? Do i need to buy one?
yes pretty much
@@mikesunboxingworth mentioning no? I'm triggered I didn't find out before now I got to wait 4 working days for a backplate...
@@huntelaar404 All am4 motherboards come with the backplate, if you can't find it check the box the motherboard came in.
@@novah589 Yeah duh. But I changed CPU cooler and found out on the first cooler I threw out the stock backplate thinking I wouldnt need it anymore.
@@huntelaar404 bit rich saying ‘duh’ after your smoothbrain ass decided to throw parts out.
Nice vid..worrying it may hit the ram
Is the fan splitter included with the ak620?
yes it is
@@mikesunboxing thanks
Do you know if there is any difference in installing this on AM5?
should be pretty similar, i had the unit just before the AM5 launch so didn't have specific instructions or fitting guide
Putting uncomfortable pressure to screw in the middle screws was kinda scary
What if you dont have the og am4 brackets
that is fine, remove them and use the ones provided
Thanks you.
Always welcome
I’ve spent at least an hour just trying to line up the 2 screws to mount the heat sink, anyone have tips?
This is maybe easier to fix or at least advise if we can ask more questions and get direct answers, so feel free to join our Discord chat and we can go over it in more detail discord.gg/XtBTGQ6BDu
Agree to the rules by clicking the emoji and you will get access to the rest of the Discord channels