The Philips GC9650/80 steam generator stops generating steam, but when it is unplugged and left for 20 minutes, it works normally again, although the pump may be a bit loud. What could be the cause?
Hello, good morning, I am a follower of your channel and I am writing to ask you for help with the following problem I have with a Bosch ironing center, with the boiler empty, and everything connected, I turn on the device and after 10 seconds the light goes out of the house, I have replaced the boiler and the electrovalve trying to find the problem, and nothing happens the same, I tried to turn it on with the cables of the boiler disconnected and the light did not go out, after this test they told me that I filled the boiler with water would not turn off the electricity, that was the problem, well then I filled it to check it, and I will explain what happened next, I turn it on, and suddenly the electricity does not go out at the moment, the minutes go by, the iron drips, pressed the steam button nothing happens or sounds, the water suction pump three quarters of the same, the temperature selector stays blinking and the permanent light does not come on, when it is supposed that after a few minutes it would have to stay on fixed light on the selected temperature and beep twice to indicate that it is ready for operation, and that does not happen, seeing the fatal operation that it had and for fear that something could happen, he pressed the off button and the light went out in the same moment, I await your help and advice to solve this problem, please, greetings.
Hello, first check your home switch board breaker or you have check the control board in the ironing,may be something wrong on the control board or temperature controller switch top of the ironing element burn and permanently on condition because over heating,need to replace the controller switch, if not send your ironing of picture to my email mohamedurabeek@gmail.com
![Jack Harlow - Hello Miss Johnson [Official Music Video]](http://i.ytimg.com/vi/Q86_nlRoIGw/mqdefault.jpg)
Very fantastic teaching thanks
The Philips GC9650/80 steam generator stops generating steam, but when it is unplugged and left for 20 minutes, it works normally again, although the pump may be a bit loud. What could be the cause?
What is the thermostat value please?
Tf260c
@@magnaticraja thank you so much
Hi, my button from the docking station got stuck on closed mode so i cannot put the steamer on it anymore, how do i open it? Any idea please?:(
Hello sir gud day.. 220 volt ba ang supply ng motor pump na yan
I need tarmsate of model 7020 how to toget.inmumbai India
What to do when the 3 buttons are blinking green?
Hello, good morning, I am a follower of your channel and I am writing to ask you for help with the following problem I have with a Bosch ironing center, with the boiler empty, and everything connected, I turn on the device and after 10 seconds the light goes out of the house, I have replaced the boiler and the electrovalve trying to find the problem, and nothing happens the same, I tried to turn it on with the cables of the boiler disconnected and the light did not go out, after this test they told me that I filled the boiler with water would not turn off the electricity, that was the problem, well then I filled it to check it, and I will explain what happened next, I turn it on, and suddenly the electricity does not go out at the moment, the minutes go by, the iron drips, pressed the steam button nothing happens or sounds, the water suction pump three quarters of the same, the temperature selector stays blinking and the permanent light does not come on, when it is supposed that after a few minutes it would have to stay on fixed light on the selected temperature and beep twice to indicate that it is ready for operation, and that does not happen, seeing the fatal operation that it had and for fear that something could happen, he pressed the off button and the light went out in the same moment, I await your help and advice to solve this problem, please, greetings.
Hello, first check your home switch board breaker or you have check the control board in the ironing,may be something wrong on the control board or temperature controller switch top of the ironing element burn and permanently on condition because over heating,need to replace the controller switch, if not send your ironing of picture to my email mohamedurabeek@gmail.com
Thank you video for
traduire en francis ou en arabe