Working perfectly You will face some errors but it will work Solution of Some errors are: 1)Keep away from sunlight 2)Give the motor less voltage if running fast(i.e. take another battery of less voltage (3v or 3.7v with 20ohm resistor) and then connect +ve to com and -ve to the negative where the motor is also connected) 3)Use black tape only 4) Relay should get proper voltage Thanks a lot sir They had assisted me on phone call and helped a lot in creating the project 🎉
Sir I have doubt can you please solve it Query : Our left side motor doesn't work but all wire are connected according as you have said in the video And some error sound is forming through it . So please solve our problem
sir the motor is not rotating but the light of ir sensor and relay are glowing sir but i have connected all the wires as u have shown in the video please solve my problem
@@skynet-robotics 18650-1200 mah 3.7v... Also I have attached HW additional batter for testing... just sound is coming in relay and motor is not rotating
Sir my robot is not working. When I turn on the robot , the wheels are not rotating, and the green light on the 5v relay is glowing but it is dimming after few seconds and the in and out LED on the sensor also
Thank's for your tutor sirr I'm from indonesia I wan't ask you, if we use arduino uno, how to make the wiring for the line follower, because i follow u for this wiring
sir as demonstrated in the video i have used same materials but the car is not working the relay and the sensors are responding but motors are not responding what to do Please respond as fast as you can
Sir the project is working but the it doesn't off the robot when line is stop .and the turn is not take by the wheel sometime ,What can I do ? Sir please Reply .....😢
I am in Sri Lanka ,I made this but somtimes it works and somtimes the left motor is not working and somtimes left motor is working , and I used two TCRT5000 ir sensors , can you discribe this matter?😥
@skynet-robotics sir the project is working but the motors speed is very fast and that y the robot is unable to turn and it goes out off track can you please help sir. i think that the motor is getting too much voltage(i am using 1 3.7 volt li-ion battery )should i use a resistor or a diode to limit the voltage
Yes . But if u want to follow white line then it can . U need just change relay connection (very simple) In short it follow black line as well as white
Sir Mera to single batrry se chal hi nahi Raha hai or jab me 2 batrry series me jod kar chalata hu chal to chal jata hai Lekin speed bhot jada hai speed ko kaise Kam Karu sir please jaldi bata do 15 Tarik ko jama karvana hai school me 😢😢
Working perfectly
You will face some errors but it will work
Solution of Some errors are:
1)Keep away from sunlight
2)Give the motor less voltage if running fast(i.e. take another battery of less voltage (3v or 3.7v with 20ohm resistor) and then connect +ve to com and -ve to the negative where the motor is also connected)
3)Use black tape only
4) Relay should get proper voltage
Thanks a lot sir
They had assisted me on phone call and helped a lot in creating the project 🎉
Sir thanks a lot sir it was very easy to make and very impressive. I make this for my scence project
I made one of these at school it worked great
Which robot is better this one or the one you made using motor driver. Which will work better ?
This would be more cost effective only worry is if it could work as good as motor driver one or equivalent to it
Sir I am from tamilnadu,Very very thank you sir it's 💯 percentage works tomorrow I submit my project at college
All the best
Very nice thank you for your video. waiting for next following robot
If we make the path crossing over each other then where will it go....pls reply.
I have to make it for my school project
It will work only on continues path
What is the length of the wooden block of the robot?
What is the height breath length of the wooden block
Sir I have doubt can you please solve it
Query : Our left side motor doesn't work but all wire are connected according as you have said in the video
And some error sound is forming through it .
So please solve our problem
Send video on WhatsApp
Sir now it's working perfectly sir thank you so much tomorrow I submit my project with confidence sir .Thank you
All the best
@@skynet-robotics per inhe oder kaise kare sari link dedo na pls
Nothing its working
sir the motor is not rotating but the light of ir sensor and relay are glowing sir but i have connected all the wires as u have shown in the video please solve my problem
Sens video on WhatsApp
Relay sound is coming but motor is not rotating... connectivity checked. whatcould be the reason.
Which Battery used
@@skynet-robotics 18650-1200 mah 3.7v... Also I have attached HW additional batter for testing... just sound is coming in relay and motor is not rotating
Sir we can use 1 relay , IR sensor
Saya masih bingung 150 rpm berapa voltase tolong di jawab sir
Bhai lithium battery hi jaruri hai ya double a aur triple a ke do tin battery use kar sakte hai
Jaldi bata
Nahi
Sir can uh give this project synopsis please
Ye dc motor aur normal battery se kam karega
Konsi wali 9v?
Wo hw company ka Jo aata hai
Lithium battery use karna jaruri hai
Sir this battery kitna mAh?? A
Or me agar 1800 mAh use kora to work karega??
Ha
@@skynet-robotics sir laptop ka ceel use kar Sakta hu?? Sir forgive me for teasing you again😊
Can I use 9v battery instead?
Bro the project is too good but I am facing a problem in which the robot is not following black line properly
Send video on whatsApp
What is the rpm of motor plz reply
Sir, can build it only 1 ir sensor
No
Sir, can we use 100 RPM gear motor in this project
Yes
Will this have any effect on speed?
@@Sachinkumarjtfgi definitely speed depends on rpm of motor
Will it work if tape is white??
Sir not following black line so what I do
Is it necessary to use ac connector??
No need
It's use only for wire join
Isko duble chanel rile se bana sakte ha
Ha
Easily bana sakte ho
Why does the wheels keep on rolling even if there is no object and sensor's sensitivity has been properly set
Can i use 2 1.5v non rechargeable battery
is the gray wire of gear motor connected to NO in relay, positive or negative?
Positive
Brother just tell ki ye black line ko follow kr rha h ya side wale white colour ko?
Black
Sir black tape konsi surface pr lagani h? Or mera project line follow nahi kr raha h kya reason ho sakta h?
Koi bhi white is best
Hi mine is not working only one motor is working but the other one is not the relay is getting the signal but the motor won't work
Check motor connection
Sir my robot is not working. When I turn on the robot , the wheels are not rotating, and the green light on the 5v relay is glowing but it is dimming after few seconds and the in and out LED on the sensor also
Which Battery u r using
@@skynet-robotics 4v 1.5ah lead acid rechargable battery
Does this circuit still work on the black board with white line? If it's not , should i change my Ir sensor position?
Yes it will work but you have to connect wire to NC port instade of NO on relay
thanks a lot
Please make a video on it please
Thank's for your tutor sirr
I'm from indonesia
I wan't ask you, if we use arduino uno, how to make the wiring for the line follower, because i follow u for this wiring
I hv made video for arduino line follower
U can check on RUclips
Line follower robot skynet robotics
line konse marker se draw krni h k ye usko sense kre
Electric wire Black tape
Sir i did it but the wheel is going backwards . How can i fix
@@artfullscales swap wires of that motor
Sir black line kese banaya. Black tape h kya?
Wire tape
I bought 5v relay but not module can i make it using this relay
Yes
Bhaiya isme jo aapne cap use kari he vo konsi cap he pls tell😢
Sanitizer ka cap use kiya hain aor usper Caster wheel lagaya
I didn't get female to female for connecting ir sensors to relay then what should I do
Solder wires
What if i use 2 lithium ion battery with switch. Will it work? Plz reply fast.
Yes
Ok thank
Sir wheels backward move horhy h how can i fix this?
Swap wires of motor
Mere project chal rha hai but black line ko follow nhi kr rha hai .jaise hi isko neeche rakho ye Jha mn kre wha chala jata hai
Sir what work does ac connector make
It's just connector
You can give joint instead of using it
@@skynet-robotics thanks brother
Sir what other thing we can use in place of AC wire joint connector
Yes 👍
That's connector use only for join of wires
Bro please reply fast, both my light on the sensor are turning on when where is nothing below the sensor
Adjust the sensitivity
Rotate potentiometer(blue color) using screw driver
@@skynet-roboticsnow only one is turning on when i keep it on the ground
sir as demonstrated in the video i have used same materials but the car is not working the relay and the sensors are responding but motors are not responding what to do
Please respond as fast as you can
Which battery u r using
3.7 volt lithium battery
please reply
But sir we use four motor in which should connect
Rpm?
Sir can you please share the buy link of IR sensor
Website under construction
I will send u link in 2-3days please wait
Sir please share the buy link of IR sensor
@@DevenderRohilla-u7v 9075800409 WhatsApp me your requirements
Please help. How can I put a switch to turn it on and off please? Thank you
Cut red wire coming from battery and insert switch between the
@@skynet-robotics between what?
@@jenaissante26 red wire of battery which u hv cut
919075800409
WhatsApp me I will send u diagram
Wooden block can be of any size?
Yes
Iski speed increase ho sakti hai kya bro?
Ha
Use 300 rpm motor or 7.4v battery
So when ir sensor detects black it means logic 0?
1
@@skynet-robotics black line absorbs ir radiation
Sir the ir sensors are working perfectly but motor is not working
Send video on WhatsApp
Can i use the relay which you used in making" short circuit protection using relay" on your recent video
Yes but u need some extra components like resister , diod etc
Sir the project is working but the it doesn't off the robot when line is stop .and the turn is not take by the wheel sometime ,What can I do ? Sir please Reply .....😢
I am in Sri Lanka ,I made this but somtimes it works and somtimes the left motor is not working and somtimes left motor is working , and I used two TCRT5000 ir sensors , can you discribe this matter?😥
@@SRD-Productionsadjust sensitivity of sensor
My 4wd not following the line and not detecting edges
Adjust the sensitivity of sensor
@@skynet-robotics I adjusted it does not working
Sir black line kaise banaye
Electric wire tape
Thanks sir
Sir aap Arduino human following robot bataeya a
Sir 2 neon battary use kar sakte hai kya kuch nahi hoga n
Sir IR sensor nahi chal raha
Hlo mera robot to sb ko follow kr rha hai lekin black line se bar bar bhag ja rha hai bina ruke Chlta hai na hi follow kr rha hai reply
Sir l have created the robot but it is not working because of please tell
Adjust the sensitivity of sensor
which wire you use to connect relay to ir sensors
Female to female
Female to female
thank you ❤️
Could u please share the link of products
@skynet-robotics sir the project is working but the motors speed is very fast and that y the robot is unable to turn and it goes out off track can you please help sir. i think that the motor is getting too much voltage(i am using 1 3.7 volt li-ion battery )should i use a resistor or a diode to limit the voltage
Use speed controller
We completed the project. but it won't stop on the black line? It's moving faster.Can you please help on this?
Which battery u r using
Lithium ion 3.7V
@@AditiJagdale-c4f rpm of motor?
150
It was working but suddenly one sensor started detecting black color though everything is at right place
It work comfortably?
Yes👍
Double Li - Ion battery se kuch short-circuit toh nahi ho na meri 7.4v ki hai , please reply sir
Nhi hoga bas speed badhega
Which v battery should we use at least sir?
I am currently using 9V battery and the speed is too fast.
7.4V
Or use 100rpm motors
One sensor is turning on when in the air and turning off when i keep it on the ground
No
it should be off when in air or black surface
Hello, can you explain how it stops when detecting an edge?
When ir sensor not detecting edge it gives 1 signal to relay
And when relay recive signal as 1 (high) it disconnect motor connection
@@skynet-robotics the relay often comes out and you need to stick it again and again.
Does it only follow black line sir plzz reply faster i have to submit it tommorow
Yes .
But if u want to follow white line then it can . U need just change relay connection (very simple)
In short it follow black line as well as white
Mobile ki black screen pe chal paye ga
Nhi
I follow your video but the sensor are not working only getting hot plz help me
Check connection polarity
sir does it need programming or not
No
Hello sir pls reply fast in the ac wire connector how to know which is positive and negative
This connector only connection purpose
Identify by battery wire connection
Written on battery holder
@@skynet-robotics so i can put it in any ?
@@mysterio17 yes but make sure battery + terminal connected to vcc pin of realy and sensor
-ve terminal of battery to Gnd pin of relay and sensor
My car didn't follow the black line but it follow my hand what will i do please reply
Send video on WhatsApp
Same problem not following black line it just kept running all the way
Can you please tell me the wires names!
Please iski bhi video dale jaldi
Hello brother it is not working in sunlight plz give me any solution
Use thermocol to cover IR sensor
Super fantastic thanks you 🙏🏻
Most welcome 😊
Its not moving pls help
Motor not working
Using 9v battery hw
I do not have ur no too
Plss help
Connected as shown in video
Plsssss hlp😢😢😢😢😢😢😢😢😢
Can we make it 4 wheel drive
Yes you can use
@@skynet-robotics my 4wd robot is not detecting edges of table and it falls off
sir can i use a diffrent rpm motor
Yes
But Use less than 150rpm
My line follower robot is not worked
What is the issue
I don't no
Can I get you a photo?
Please tell me soon
Where is the switch sir?
There is no switch you need to put in the battery to start
Sir Mera to single batrry se chal hi nahi Raha hai or jab me 2 batrry series me jod kar chalata hu chal to chal jata hai Lekin speed bhot jada hai speed ko kaise Kam Karu sir please jaldi bata do 15 Tarik ko jama karvana hai school me 😢😢
Use 100rpm motor
Or
Connect motor connection to sigal battery and sensor connection to Double battery
@@skynet-robotics sir 100 rpm moter ka istemal hi Kiya hai
Please give me a reply because I have to submit it on 26/12/24
What are the components all
ir sensor
5v single channel relay
18650 li-ion battery
150rpm gear motor
Excelente projeto.
Thnx
Why did we use a 3.7V battery?
We are not using any voltage regulator .
IR sensor need approximately 5V thats why
Otherwise you can use two batteries 7.4 V
Hi sir i have done everything but it doesn't work pls reply i have to submit it tomorrow
My robot is not stopping when it get off from table
Adjust sensitivity
Bro one wheel not working inee
To submit tomorrow fasst
What would be the cost?
450/-
hlo sir my all sensor is working but motor is not rotating plz help sir
send video on 9405276005
Cost kya hoga project me
1800/-