Old video but anyway. I had my tap machine checked by electrician and they told me that the compressor is dead. Are there any spare compressors available?
What temp controller did you end up using? I think my temp controller is broken (no lighting up or fan turning on) but I have power coming out of the power supply.
well the board and the temp controller are not mated in anyway.. the power supply is 12 volt.. 4 wires 2 fore 12 volt and 2 for output to fan and compressor.. very simple to repair.. can use normal 12 volt supply and 2 relays to trigger compressor and fan.
well if you have controllers using pic chips that have custom firmware the only way to repair them is using an exact board to pull the firmware from the pic and write a new one or check if you can find firmware online but most are patent protected then the only choice is to write new firmware. that takes about 3 days if you have a working unit.
@@JDNelRefrigeration most controllers, depending on the fault either have a faulty relay or relay driver. if their is no power at all check caps and semi conductors.
I have power going to my machine as it lights up but no display on temp contains the motor doesn’t turn . Will this just be a temp control replacement?
You have to test it first. Inside your temperature controller there is a relay, the 2 contacts of the relay must be bypassed in order to see if the compressor runs. If not you have to look further.
I connected the compressor direct to input and it started to run . Can I now just go ahead and buy a new danfoss temp control and splice that into the 240?
Hey dude! Awesome work!!! I have byed a used machine these days and i am wondering how the original temperature control works? If i press setup i can set it down to -1 but not more. Original it was set to -0.1. What does these numbers mean? Maybe you can help me... thank you and enjoy your great maschine!
JDNelRefrigeration I have a machine that was not used for months and when I I tried to rinse it with room temperature water it was working now it won’t drain from the spout is it clogged up or is there a pump that gave up inside?
@@minion3635 The original machines made by Jagermeister have no pump, it is all gravity feed. But i have seen many copies that use pumps. I open them and have a look inside.
super repair video ,danke
Old video but anyway. I had my tap machine checked by electrician and they told me that the compressor is dead. Are there any spare compressors available?
Yes, they are freely available.
What temp controller did you end up using? I think my temp controller is broken (no lighting up or fan turning on) but I have power coming out of the power supply.
I used a Danfoss temperature controller.
well the board and the temp controller are not mated in anyway.. the power supply is 12 volt.. 4 wires 2 fore 12 volt and 2 for output to fan and compressor.. very simple to repair.. can use normal 12 volt supply and 2 relays to trigger compressor and fan.
repaired a few in capetown.
I have never been able to repair a faulty controller. The power supply is easy.
well if you have controllers using pic chips that have custom firmware the only way to repair them is using an exact board to pull the firmware from the pic and write a new one or check if you can find firmware online but most are patent protected then the only choice is to write new firmware. that takes about 3 days if you have a working unit.
@@JDNelRefrigeration most controllers, depending on the fault either have a faulty relay or relay driver. if their is no power at all check caps and semi conductors.
You possibly don't have a wiring diagram to share??
Im in states....do you have a wiring diagram on how you did added the temp controller...my lights work but my machine keeps freezing up
The replacement temperature controller comes with a diagram
Wondering if you could help. Can’t find anything online. I switch it on and all the LEDs just flash. Any ideas what could be wrong?
I would check the power supply first.
You can buy the power supply board from their website for $20
On this machine the temperature controller board was faulty. Not the power supply.
I have power going to my machine as it lights up but no display on temp contains the motor doesn’t turn . Will this just be a temp control replacement?
You have to test it first. Inside your temperature controller there is a relay, the 2 contacts of the relay must be bypassed in order to see if the compressor runs. If not you have to look further.
I connected the compressor direct to input and it started to run . Can I now just go ahead and buy a new danfoss temp control and splice that into the 240?
@@patrickmcnaughton308 Yes.
It actually should be running at -17.8 according to there website
At -14 it was barely coming out of the spout but the controller is adjustable, you can have it at any temperature you like.
What temp probe did you use?
I left the original one inside the machine. I found a controller that is compatible to the existing probe.
That is Cool
Dose it matter what type of temperature controller I use?
No, as long as it has the right temperature range and is compatible to the sensor probe.
Hey dude! Awesome work!!!
I have byed a used machine these days and i am wondering how the original temperature control works? If i press setup i can set it down to -1 but not more. Original it was set to -0.1. What does these numbers mean?
Maybe you can help me... thank you and enjoy your great maschine!
I don't know but I would guess it's degrees Celsius or Fahrenheit
Mine is set to 10 (Fahrenheit)
It's impossible for me to change the temperature.
Have you solved it or did you swap the temp controller?
@@rickardgustavsson9328 I swapped the temperature controller.
@@JDNelRefrigeration yup I did that too today.
I used a Eliwell EW961 and it works very well. Still using the power board to feed the led lights 👍🏼
oh btw, I wrote down how I did my modification on my github. github.com/Zeppen/J-germeister-tap-machine-mod/wiki
i wanna buy dis
My machine is plugged its about 5 years old, i am not sure what to do. I tried blowing air back through the spout still nothing.
You may have to rinse your machine out with boiling water.
JDNelRefrigeration I have a machine that was not used for months and when I I tried to rinse it with room temperature water it was working now it won’t drain from the spout is it clogged up or is there a pump that gave up inside?
@@minion3635 The original machines made by Jagermeister have no pump, it is all gravity feed. But i have seen many copies that use pumps. I open them and have a look inside.
JDNelRefrigeration thank you
how much for this??
Price of the controller plus labour charge. Price dependent on supplier at the time.
First view = first like