Installing Rear and Front Sway Bars on your 3800
HTML-код
- Опубликовано: 10 сен 2024
- There's nothing better than cruising around in your 3800, but steering them can be like steering a boat. Our new front and rear solid sway bars will fix that problem. Bo explains how they will upgrade your ride and how to install them. #ZZP #GoFastNotBroke
Find our rear and front sway bars here: zzperformance....
ZZP is located in Wyoming, MI. We are the world’s largest supplier of aftermarket performance parts for 3800, Sonic/Cruze, Ecotec, and ATS platforms, providing industry-leading customer service and support.
Our staff of professionals has experienced knowledge in all the vehicle platforms we represent. ZZPerformance is dedicated to 100% customer satisfaction. We provide you with highly specific technical information, that can’t be found anywhere else.
Interested in modding your car? Check out our parts at zzperformance.com
Questions about modding? Email us at customerservice@zzperformance.com
Coating those end link bushings and bar grommets in white lube will prevent cold weather squawk. Very old hot rodder tip that works.
A while back I threw the rear sway bar on my old Buick LaCrosse and man was it an improvement. Went from constantly fighting understeer to getting braking oversteer if I chucked it in hard enough. That car surprises a lot of people, no one expects a grandpa car to out corner them lol.
What’s year I have a 08 looking to do?
@@ericberry5134 It was an '07 LaCrosse CXL, Went with the ZZP rear sway bar and kept the factory front.
prob one of the best auto companies tbh, yall do it all
Good video. Good information. I would be the one who took off my old one and forgot which way is up! LOL. Just got my rear sway bar and front strut tower supports today. Want to play hooky from work tomorrow just to put them on... the coilovers are the next move so I'll wait. 🙄 If they perform like they did on the 96 Toyota, my boat baby will handle like it's on tracks. Can't wait! Thanks again! And keep the vids coming. Great tools!
I should trade in my old style rear sway bar for the new one. 🤔 good video
Just replaced both sway bars on my 2004 Monte Carlo SS. Much bigger and stiffer than the FE4 suspension with the hollow tubes. The roads have been snowy and nasty the last couple of weeks here in northern Michigan. I have not had a chance to test it out on some curves yet.
We feel your pain. 🥶
Bummer man 😳. The best cure for that kind of pain is a one way ticket to Georgia. Sunny today with a high of 65 degrees. WELCOME SOUTH, BROTHER 😁🇺🇸✌🏻
There are better install videos by customers. While it didn’t necessarily hurt to put grease on the inside of rear sway bar bushing (rubber doesn’t squeak) putting it on the outside between the bracket is a no. U don’t want the bushing to walk or move on the bracket. Also depending what “grease” he put on it might actually break the rubber down faster.
Never use petroleum based grease on rubber grommets or bushings. Certified tech 101.
Great helpful video! Now I will scrap my poorly made Addco rear sway bar [they use mickey mouse clamps instead of making bar properly]. Thanks for vid.
Do any of these mods fit the 03 Bonneville ssei? Poor bonnie feels left out alot lol
ZZP videos are the most important tools for upgrade installations on W-bodies (including others) that doesn’t need a toolbox for storage. The normally dark areas under the chassis are well lit to help with visual confirmation of all components. Having a vehicle lift provides plenty of ground clearance for maneuvering the anti-sway bars but the rest of us will do fine with our Jack stands, no doubt.
Maybe the camera or lighting angle caused it but the wear patterns on the rear rotors look like only the inner half of the rotor was making firm contact with the pads. Kinda like the caliper pistons were making uneven contact with the pads. Maybe the pads are just very narrow but if only half of the rotors are being used then the braking system capacity is being reduced by 50%. Most likely it’s my skewed perception of the video and nothing more. Otherwise it’s another good video from the folks at ZZP 👍.
... Probably testing sticking calipers.. 🥺
@@egrayson2031 … Those test results would be a drag. Kinda like a stuck caliper 😁.
I need my front sway bar replaced on my 07 buick lacrosse. It looks like it would fit fine. Can you confirm?
Does anyone know if this will fit a 1998 Buick riviera?
I didn't know Jesse Pinkman was a mechanic!
Will that fit my 1994 Buick Regal Coupe; its loose on right side-should I replace the whole thing with this or keep it stock ( its a daily driver not performance car by any means)
Too bad ZZP doesn't offer these for the H body like my 2005 LeSabre.
What's leaking oil up there? Is it the oil pan like my 04 GTP ? & are the GTP sway bars better then what you're replacing here? It don't feel any over steer. Thanks.
Ls4 front sway bar
Question I'm new to the platform all of cars listed are my dream cars but I got 05 buick lesabre I've been wanting one for a while is it a w body to because if so it will help me in long run
LeSabre is an H-Body car, like it's cousin the Bonneville. Only thing you share with the w-bodies is the engine and transmission.
@@sazzyPheox true but weights don't differ very much just width besides the sway bar being more narrow on w body could by any chance the mounting for coil overs be same who knows might fit just don't know considering gm likes to interchange all parts figure could be similar
Can I put a sway bar on the rear of my 01 lesabre?
Would this fit on a 2013 chevy impala ltz
Can these be put in a 90-94 gen 1 lumina?
Silly question, but is it ok to spray paint the sway bar? I want mine to be silver.
Of course, go right ahead!
are these not on your site anymore for sale?
Still available!
zzperformance.com/collections/3800-suspension/products/zzp-rear-sway-bar
zzperformance.com/collections/3800-suspension/products/zzp-front-sway-bar
can I use the cheaper none adjustable rear links from zzp on that same red zzp sway bar?
Yes should be able to
will this fit on a 91 regal??????
If you were in the driveway on jackstands .. how would you pull downwards on it if the ground was there? Lol this video the car was in the air 3:30
JACK STANDS,
You aren't very bright, are you?
FYI, his instructions for telling you to install the front bar with the bend facing up is incorrect. The bend should be facing down for two reasons. Some w body’s mid pipe may not clear the other way and the tie rods will contact the bar his way too. They’re are small reliefs on the bar to hep clear the tie rods only on one side of the bar and his way they don’t exist and will hit slightly under full lock. Trust me, I know.
No
We installed this sway bar on 07 GP last year and worked perfectly fine with the original exhaust system until we decided to replace the exaust for an aftermarket set of headers. The problem is when I select reverse and the engine naturally moves backward the down pipe is touching sometimes and produces a sort of vibration that feels strong inside of the car we are looking to reinstall upside down this sway bar hoping that solve the vibration issue.
Can u use OEM rear endlinks for the rear sway bar?
Yup!
Yes