So to program the second key (Transponder and remote), do I need to use a second slot in the car system or use the same as the original key ? This is to allow to working keys for a car. thanks
Hello, can you please help? This is for 2008 Mazda CX7 with a used to be working key fob entry system. The car starts fine, the keyless entry portion stopped working. After doing all procedure for programming locking and unlocking, based on the cycle responses from the vehicle, the key fob should had been programmed. But the car computer never saved the information of the key fob. The keyless entry still does not work. It used to work until I tried to start the car with a key that had no transponder chip in it. After that, the working keyless entry portion of the fob stopped working and I seem not to be able program it again. Can you help on what the problem might be? Thank you so much.
I keep seeing so many videos of people using the SKP-900 on so many different vehicles. I barely see videos of the X100 Pad 2...you sure X100 Pad 2 is a better machine? Do you recommend any other tools (like X100T or Nissan NSPC001) I should purchase with the X100 Pad 2 so that I can increase the amount of vehicles I can program?
Hello. Please help. My mazda cx9 2008 has a keyless. 2 cards that work once and fail. Then I have to put the metal key in the ignition. Then the engine always starts. If you manage to start the engine without the key, the "key" light flashes red on the board. Smart key opens and closes the car. The only problem is sometimes I turn the ignition switch and the second time I do not and I have to take the key, the tip. The buttons on the door handle also do not work. Sometimes I press the button multiple times and manage to open the door. I have the impression that the cards are not always seen by the keyless module. What could be the problem? Forscan shows an error. Code: B1600 - PATS ignition key transponder signal is not received. - Possible causes - - Defective ignition key - PATS antenna or cables damaged - Damage to the PCM Module: Opening the door locks with a remote control (no keys required)
So there should be new key in ignition from the beginning? I've tried on 2007 Mazda 5 with old key in ignition from the beginning (only changed it to new when it says "please change a new key"). It said "success" at the end, but new key is not programmed! I even tried "all keys lost", same thing - says "success", but nothing changed - old key's working, new key's not working. What I'm doing wrong? Could it be bad or wrong chip in new key? VVDI2 says 4D+ DST 80, ID83 Ford/Mazda/Lincoln Also, is it necessary to disconnect SKP before testing the new key?
So to program the second key (Transponder and remote), do I need to use a second slot in the car system or use the same as the original key ? This is to allow to working keys for a car. thanks
Thanks works great. Saved me some money for sure.
Hello, can you please help? This is for 2008 Mazda CX7 with a used to be working key fob entry system. The car starts fine, the keyless entry portion stopped working. After doing all procedure for programming locking and unlocking, based on the cycle responses from the vehicle, the key fob should had been programmed. But the car computer never saved the information of the key fob. The keyless entry still does not work. It used to work until I tried to start the car with a key that had no transponder chip in it. After that, the working keyless entry portion of the fob stopped working and I seem not to be able program it again. Can you help on what the problem might be? Thank you so much.
Do you recommend SKP900 for all keys lost for all cars?
Where can I get one in USA?
I keep seeing so many videos of people using the SKP-900 on so many different vehicles. I barely see videos of the X100 Pad 2...you sure X100 Pad 2 is a better machine? Do you recommend any other tools (like X100T or Nissan NSPC001) I should purchase with the X100 Pad 2 so that I can increase the amount of vehicles I can program?
👆
Thank you very much bro
if all keys lost. no need to add 2 keys?
Where do you recommend I buy keys from? Do you have any luck with eBay keys?
Hello. Please help. My mazda cx9 2008 has a keyless. 2 cards that work once and fail. Then I have to put the metal key in the ignition. Then the engine always starts. If you manage to start the engine without the key, the "key" light flashes red on the board. Smart key opens and closes the car. The only problem is sometimes I turn the ignition switch and the second time I do not and I have to take the key, the tip. The buttons on the door handle also do not work. Sometimes I press the button multiple times and manage to open the door. I have the impression that the cards are not always seen by the keyless module. What could be the problem? Forscan shows an error. Code: B1600 - PATS ignition key transponder signal is not received.
- Possible causes -
- Defective ignition key
- PATS antenna or cables damaged
- Damage to the PCM
Module: Opening the door locks with a remote control (no keys required)
💩
Any could help me to found a pin code for Mazda CX-7 2007?
So there should be new key in ignition from the beginning? I've tried on 2007 Mazda 5 with old key in ignition from the beginning (only changed it to new when it says "please change a new key"). It said "success" at the end, but new key is not programmed! I even tried "all keys lost", same thing - says "success", but nothing changed - old key's working, new key's not working. What I'm doing wrong? Could it be bad or wrong chip in new key? VVDI2 says 4D+ DST 80, ID83 Ford/Mazda/Lincoln
Also, is it necessary to disconnect SKP before testing the new key?
Mazda 5 uses 4D 63 (80-Bit)Maybe that's your problem.
Yeah, I figured that out already. ID83 was supplied with key. I've used VVDI2 to reconfigure chip as 4D63, will try again. Thanks!
ruclips.net/video/Q0TBIXYV9Mk/видео.html
EXCELLENT
Great man
😘👍