As a crafter who's done shows, I REALLY appreciate you showing your process! I have been dying to try doing these, for personal use only & family gifts...so THANK YOU!!❤️❤️
These are the first water bottles I’ve ever painted. I put a coat of metal primer on the bottom half, then added a scene. I thought I had purchased oil pains, but accidentally picked up watercolor tubes😮. I had gotten far enough in the project that I had to just keep going. To seal, I first put on 2 coats of Krylon spray varnish (ok for metal & wc) to seal the watercolor paint. This dried fantastic. As my waterproof sealant, I used a brush-on matte by DecoArt, Dura Clear. Each thin coating still made the watercolor paint run in fine lines, mixing colors if the brush overlapped. Is it too late to use an Epoxy to waterproof it?
You can, however it won't be as durable and from my experience, it had the tendency to yellow more quickly. I believe that rustoleum sells a clear coat. New things are always popping up though, so if you see a spray on resin, give it a try on something small first before doing your water bottle.
Hi I was wondering if you uploaded a vid on how to remove the excess resin yet? I just finished my bottle but I have no idea how to remove it w out damaging the bottle
Hello!! I have a question about the resin. I'm getting a dishwasher safe Flask and I want to dishwash the bottle after its customised. (for sanitary reasons, no scrubber I've had gets every spot and then it goes bad so the dishwasher is a must) Would the resin turn soft and run off if I put the bottle in the dishwasher? Do I have to buy a dishwasher safe resin for this too?
I'm not sure how it would effect a non waterproof sticker honestly. Resin isn't water based, but if you don't have a cup turner then my guess is that the ink from the sticker would run.
Is there a certain way you like to cut off the drips at the bottom of the cup? Would using sand paper work on smoothing it out? What is the best way to get rid of the drips?
I heat it up with a heat gun or blow dryer and cut them off with an exacto knife. I usually just cut in a circle around the whole bottom of the bottle and then the resin will just peel up. Sanding also works, but I recommend still cutting the tips of the drips off to level them out, otherwise they could snag on the sander and cause your resin to chip on the sides.
so how well does the cured resin hold up to cleaning agents such as harsh soap or bleach &/or hot water? also any noticeable discoloration over time? and lastly the durability from daily use any noticeable scuffing?
The resin I use is Heat resistant up to 500 degrees, it's pretty durable but I don't know how bleach wojld effect it. It's actually meant for countertops so I assume it should be fine. It should not be placed in the dishwasher though, metal water bottles in general should not be and every resin artist I know would suggest against putting any resin item in the dishwasher.
Yes you need to heat it up first, because it allows your cuts to be more precise. I actually have a newer video on how to cut resin drips if you don't have a cup turner.
Hi Bexx, thanks so much for this video, love your bottles! So are you saying that it's not required to have those tumbler/bottle turner things to keep the resin from dripping off and being consistent throughout the bottle? I would love to see what the bottles look like after they dry and after you cut off the drips. Is it smooth all round? If so, this is amazing! I sell personalised water bottles with person's name stuck on with adhesive vinyl, but I'd love to put resin over it afterwards to make sure it lasts for a long time rather than peel off few weeks/months down the track. Thank you :)
I'm sorry I'm only just now seeing this. No you don't need a cup turner, but it does make it easier to be consistent. What I usually do when I have too many orders to use my cup turner is cut off the drips then add a layer of resin to the bottom by itself. I haven't had too much of an issue with the bottles being smooth, as long as I use a heat gun to pop the bubbles and smooth out any areas before the resin starts to cure.
I have never done any sort of epoxy work. Do you need to prep the Hydro flask before applying a layer of epoxy, sanding etc…. I would like to seal stickers to my flask. Do I need to epoxy a layer first before applying my stickers then another layer? Or can I apply stickers to the flask without it and then epoxy? Sorry if I sound uneducated with this…but I am! 😆
It depends on if you are planning to paint or spray paint the hydro flask before adding resin. If you are painting it then no you don't need to prep anything. If you are just putting stickers on and then adding resin it's best to lightly sand the hydro flask first so the resin sticks everywhere. So I would 1. Sand it, 2. Add stickers, 3. Add 1-2 layers of resin. Hope this answers your questions!
Please always wear an organic vapor respirator when working with ALL types/brands of epoxy.just bc it doesnt smell has low voc doesn't mean it's safe. Wear nitrile gloves and use in a properly ventilated area that has akr flow going outside and bringing fresh air in. An open window or bathroom/kitchen exhaust fan wont cut it. Don't resin/epoxy in your home.. Any building with people or animals. Even in your basement isn't ok unless.u have an epoxy tent with proper ventilation to outside. I recommend highly KSRESIN Please please dont be careless like shes being. Wear your hair up. Epoxy in a properly set up and ventilated room. Wear full PPE for epoxy For more epoxy education and info how to make stuff, where to buy blanks, proper PPE and set up or ask questions, Check out epoxy is not my friend on fb. I love epoxy/resin crafts. Just educate yourself first and don't be wreckless with your health or your family's and pets. Flynn sisters boutique on YT has countless amazing in-depth tutorials. . following proper protocol. No hate. Just trying to look out for others, so they dont end up like me.. 34 and on oxygen for the rest of their life.
Thank you for this, I didn't wear my mask in this video so people could understand me talking and any hearing impaired person could potentially read my lips as well. But you are 100% correct
you have to mix it because it's two parts that activate when mixed together. I'm not sure if it would be considered resin if it was pre-mixed but some other sealant. You do not have to use resin as a sealer, I just personally think it's the best. I suggest experimenting to see what you like best.
Hi, I'm sorry I'm only just now seeing this. You'll definitely want to take the boot off, resin will not stick to the rubber and will simply peel off. Once your bottle has cured definitely keep using the boot to protect it though, if the bottle gets dented then the resin will crack.
Yes, I've done resin over plenty of stickers and haven't had an issue. Just make sure that the sticker is really well attached to the bottle so you dont get air bubbles around the edges.
How do you keep the epoxy from getting onto the threads? If you do happen to get epoxy on the threads, do you simply cut them off with your Exacto knife?
The threads, that's what they're called. You tape around them with painters tape. Please always wear an organic vapor respirator when working with ALL types/brands of epoxy.just bc it doesnt smell has low voc doesn't mean it's safe. Wear nitrile gloves and use in a properly ventilated area that has akr flow going outside and bringing fresh air in. An open window or bathroom/kitchen exhaust fan wont cut it. Don't resin/epoxy in your home.. Any building with people or animals. Even in your basement isn't ok unless.u have an epoxy tent with proper ventilation to outside. I recommend highly KSRESIN Please please dont be careless like shes being. Wear your hair up. Epoxy in a properly set up and ventilated room. Wear full PPE for epoxy For more epoxy education and info how to make stuff, where to buy blanks, proper PPE and set up or ask questions, Check out epoxy is not my friend on fb. I love epoxy/resin crafts. Just educate yourself first and don't be wreckless with your health or your family's and pets. Flynn sisters boutique on YT has countless amazing in-depth tutorials. . following proper protocol. No hate. Just trying to look out for others, so they dont end up like me.. 34 and on oxygen for the rest of their life.
I use a heat gun to get the bubbles to rise, you can also use a blow dryer or blow torch. You get more bubbles the faster you stir, so if you do it nice and consistent you shouldn't have too many.
Hi, I was wondering if u had anyone drop the hydroflask and the epoxy broke off with the paint. I saw a video about that and I'm unsure if that will happen to the hydroflasks. Anywho thank u for the tutorial!!
It really depends on how it lands. I've dropped mine onto the road from my lifted truck and It's been fine. But unfortunately resin is not indestructible so if the bottle gets dented it will likely crack or chip.
Hey I’ve been watching this video for a while and I’ve actually started to customize my own bottles, but I run into one problem that keeps reoccurring. Whenever I try to coat my bottles and resin when they’re fully cared it starts to shrink towards the top of the bottle and it creates these shrinkage lines. Now, I don’t know if it’s the type of resin then I’m using but I’m going to try switching to the one that you’re using because it seems to work very well but if you have any tips or know why it’s doing this please respond back to me!
I have never experienced that issue myself. It sounds very strange. To me it sounds like it's probably the resin, or possible the temperature in the area that you're doing it. Resin is very sensitive and works best at temperatures around 70-75, it also does not do well in humidity. Hopefully this helps, sorry for my delayed response I had a baby a few months ago.
@@bexxfineart2268 oh no problem! I figured it was the temperature I had it at, thank you for the response and I hope you and your new family are doing well 🙂❤️
@@bexxfineart2268 you make it look so easy! I used art Resin and have bumby areas. Did i not mix it well? Does Countertop epoxy work better for this purpose?
@@iitsMissy it definitely takes practice to get it perfect. Some resins gave more bubbles than others, but you definitely have to use a heat cut or a blow dryer at the very least to pop the bubbles. Wait about 15 minutes after you put the resin on the surface then use one of those tools to gently pop them. A lot of artists use blow torches as well as a super easy way to pop bubbles.
The tumblers are gorgeous. Thanks for the video. The music is nice, but as a hearing impaired person I’m having a very difficult time hearing you over the music which is louder than your voice. Please lower the music in future videos for those of us with hearing issues. I’m grateful you didn’t wear the mask bc I was able to do some lip reading. Looking forward to more of your videos. The art is lovely.
Thank you for your feedback, because of your comment I have stopped using music through my tutorials when I'm speaking or have kept it extremely low so it's not as distracting.
I didnt wear a mask in this video so that way I could give clear directions and explanations. But yes the resin I use is 100% non toxic, however I still always wear a mask.
You can use whatever sealer you personally thinks best. I would recommend testing it out before putting it on a bottle though. The reason I use resin, is because it's durable, doesn't yellow like other sealers, and can withstand a good amount of heat.
I make sure to scrape the edges of the cup and the popsicle stick frequently, as directions state for mixing every resin. I haven't had any issues in the 4 years I've been using it🤷🏼♀️ But this is something I should have elaborated on for newbies to resin, so thank you.
Can I apply resin on the glass bottles that I paint with acrylic paints??....also how do I avoid the dripping of resin as I'm not well versed with cutting the excess..
As a crafter who's done shows, I REALLY appreciate you showing your process! I have been dying to try doing these, for personal use only & family gifts...so THANK YOU!!❤️❤️
you're welcome, I became frustrated with other artists being so secretive about their process, so I didn't want anyone else to have to feel that way.
That is fabulous!! Thanks for sharing and giving me ideas!
Well done. Thank you. Happy to find a more durable option for Hydro Flask custom art!
it takes a little more effort, but totally worth it. I've had my own personal bottle for over 3 years and only just recently chipped it.
Beautiful work
Thank you for this information 🙏
Oh wow. Beautiful
Im glad you showed using the dixie cups because its hard to find attachments to spin those bottles
Yes it is, I use a cup turner now, but I have to do a lot of tweaks to get the bottle to be level.
Gaaasp!! Such beautiful work!! 😍
This was helpful. Thank you
These are the first water bottles I’ve ever painted. I put a coat of metal primer on the bottom half, then added a scene. I thought I had purchased oil pains, but accidentally picked up watercolor tubes😮. I had gotten far enough in the project that I had to just keep going.
To seal, I first put on 2 coats of Krylon spray varnish (ok for metal & wc) to seal the watercolor paint. This dried fantastic.
As my waterproof sealant, I used a brush-on matte by DecoArt, Dura Clear. Each thin coating still made the watercolor paint run in fine lines, mixing colors if the brush overlapped.
Is it too late to use an Epoxy to waterproof it?
Those look so nice!! : )
Hello would you mind doing a video of how you remove the excess resin from the cups after they are dry please. Thank you.
Love that suggestion, I will definitely try to make one.
If I wanted to do this over stickers I put on my water bottle could I do a second coat of the epoxy?
Yes you can!
Can you use spray resin instead of this method? If so, what brand would you recommend? I used Rust-Oleum metallic as my base spray paint
You can, however it won't be as durable and from my experience, it had the tendency to yellow more quickly. I believe that rustoleum sells a clear coat. New things are always popping up though, so if you see a spray on resin, give it a try on something small first before doing your water bottle.
I’d really like to see how to cut the resin drips
I have a video of how to cut drips off a cup, which is the same process.
How many layers over water bottles with stickers would be recommended?
probably 2, just depending on how smooth you want it.
@@bexxfineart2268 is fewer mean it is more rough? Sorry about all the questions I’m new to this
Hi I was wondering if you uploaded a vid on how to remove the excess resin yet? I just finished my bottle but I have no idea how to remove it w out damaging the bottle
I have not made one for RUclips, but if you have tik tok I do have one there
Hello!! I have a question about the resin. I'm getting a dishwasher safe Flask and I want to dishwash the bottle after its customised. (for sanitary reasons, no scrubber I've had gets every spot and then it goes bad so the dishwasher is a must) Would the resin turn soft and run off if I put the bottle in the dishwasher? Do I have to buy a dishwasher safe resin for this too?
I would not recommend putting it in the dishwasher
Will this work for non waterproof stickers on hydro flask too?
I'm not sure how it would effect a non waterproof sticker honestly. Resin isn't water based, but if you don't have a cup turner then my guess is that the ink from the sticker would run.
What’s the brand of the counter top epoxy you use
It's called Countertop Epoxy, and I use the FX premium poxy
Is there a certain way you like to cut off the drips at the bottom of the cup? Would using sand paper work on smoothing it out? What is the best way to get rid of the drips?
I heat it up with a heat gun or blow dryer and cut them off with an exacto knife. I usually just cut in a circle around the whole bottom of the bottle and then the resin will just peel up. Sanding also works, but I recommend still cutting the tips of the drips off to level them out, otherwise they could snag on the sander and cause your resin to chip on the sides.
so how well does the cured resin hold up to cleaning agents such as harsh soap or bleach &/or hot water? also any noticeable discoloration over time? and lastly the durability from daily use any noticeable scuffing?
The resin I use is Heat resistant up to 500 degrees, it's pretty durable but I don't know how bleach wojld effect it. It's actually meant for countertops so I assume it should be fine. It should not be placed in the dishwasher though, metal water bottles in general should not be and every resin artist I know would suggest against putting any resin item in the dishwasher.
So you heat up the drips to cut them off? Can't use an exacto knife?
Yes you need to heat it up first, because it allows your cuts to be more precise. I actually have a newer video on how to cut resin drips if you don't have a cup turner.
Hi Bexx, thanks so much for this video, love your bottles! So are you saying that it's not required to have those tumbler/bottle turner things to keep the resin from dripping off and being consistent throughout the bottle? I would love to see what the bottles look like after they dry and after you cut off the drips. Is it smooth all round? If so, this is amazing! I sell personalised water bottles with person's name stuck on with adhesive vinyl, but I'd love to put resin over it afterwards to make sure it lasts for a long time rather than peel off few weeks/months down the track. Thank you :)
I'm sorry I'm only just now seeing this. No you don't need a cup turner, but it does make it easier to be consistent. What I usually do when I have too many orders to use my cup turner is cut off the drips then add a layer of resin to the bottom by itself. I haven't had too much of an issue with the bottles being smooth, as long as I use a heat gun to pop the bubbles and smooth out any areas before the resin starts to cure.
could you please share the link to this epoxy?
www.countertopepoxy.com/countertop-epoxy/#
You may have already bought it or something else, but here is the link to the exact kind I use
I have never done any sort of epoxy work. Do you need to prep the Hydro flask before applying a layer of epoxy, sanding etc…. I would like to seal stickers to my flask. Do I need to epoxy a layer first before applying my stickers then another layer? Or can I apply stickers to the flask without it and then epoxy? Sorry if I sound uneducated with this…but I am! 😆
It depends on if you are planning to paint or spray paint the hydro flask before adding resin. If you are painting it then no you don't need to prep anything. If you are just putting stickers on and then adding resin it's best to lightly sand the hydro flask first so the resin sticks everywhere. So I would 1. Sand it, 2. Add stickers, 3. Add 1-2 layers of resin. Hope this answers your questions!
@@bexxfineart2268 Yes, that answered my question perfectly. Thank you so much! 🤗
Please always wear an organic vapor respirator when working with ALL types/brands of epoxy.just bc it doesnt smell has low voc doesn't mean it's safe.
Wear nitrile gloves and use in a properly ventilated area that has akr flow going outside and bringing fresh air in. An open window or bathroom/kitchen exhaust fan wont cut it.
Don't resin/epoxy in your home.. Any building with people or animals. Even in your basement isn't ok unless.u have an epoxy tent with proper ventilation to outside.
I recommend highly KSRESIN
Please please dont be careless like shes being. Wear your hair up. Epoxy in a properly set up and ventilated room. Wear full PPE for epoxy
For more epoxy education and info how to make stuff, where to buy blanks, proper PPE and set up or ask questions, Check out epoxy is not my friend on fb.
I love epoxy/resin crafts. Just educate yourself first and don't be wreckless with your health or your family's and pets.
Flynn sisters boutique on YT has countless amazing in-depth tutorials. . following proper protocol.
No hate. Just trying to look out for others, so they dont end up like me.. 34 and on oxygen for the rest of their life.
Thank you for this, I didn't wear my mask in this video so people could understand me talking and any hearing impaired person could potentially read my lips as well. But you are 100% correct
Quick question why do you mix to resin? Plus, do I have to mix mines as well or I can just buy the counter top resin and use it on its own.
you have to mix it because it's two parts that activate when mixed together. I'm not sure if it would be considered resin if it was pre-mixed but some other sealant. You do not have to use resin as a sealer, I just personally think it's the best. I suggest experimenting to see what you like best.
These came out beautiful! 💜 My hydro flask has the silicone boot, would I remove the boot or keep it on while adding resin?
Hi, I'm sorry I'm only just now seeing this. You'll definitely want to take the boot off, resin will not stick to the rubber and will simply peel off. Once your bottle has cured definitely keep using the boot to protect it though, if the bottle gets dented then the resin will crack.
Would this work if I have stickers on my bottle?
Yes, I've done resin over plenty of stickers and haven't had an issue. Just make sure that the sticker is really well attached to the bottle so you dont get air bubbles around the edges.
Turn down the music some please
Did you paint the hydro flask 1st?
Yes, I spray paint it, then paint it with acrylic before adding resin.
Can these be put in the dishwasher?
No they are handwash only
How do you keep the epoxy from getting onto the threads? If you do happen to get epoxy on the threads, do you simply cut them off with your Exacto knife?
Hi, I'm not sure what you mean by the "threads" could you be more specific so I can better answer your question
The threads, that's what they're called.
You tape around them with painters tape.
Please always wear an organic vapor respirator when working with ALL types/brands of epoxy.just bc it doesnt smell has low voc doesn't mean it's safe.
Wear nitrile gloves and use in a properly ventilated area that has akr flow going outside and bringing fresh air in. An open window or bathroom/kitchen exhaust fan wont cut it.
Don't resin/epoxy in your home.. Any building with people or animals. Even in your basement isn't ok unless.u have an epoxy tent with proper ventilation to outside.
I recommend highly KSRESIN
Please please dont be careless like shes being. Wear your hair up. Epoxy in a properly set up and ventilated room. Wear full PPE for epoxy
For more epoxy education and info how to make stuff, where to buy blanks, proper PPE and set up or ask questions, Check out epoxy is not my friend on fb.
I love epoxy/resin crafts. Just educate yourself first and don't be wreckless with your health or your family's and pets.
Flynn sisters boutique on YT has countless amazing in-depth tutorials. . following proper protocol.
No hate. Just trying to look out for others, so they dont end up like me.. 34 and on oxygen for the rest of their life.
@@mies.1742 thank you for the help! I truly appreciate it!
Thank you for this tutorial! How do you avoid air bubbles within the resin? Is that a problem at all?
I use a heat gun to get the bubbles to rise, you can also use a blow dryer or blow torch. You get more bubbles the faster you stir, so if you do it nice and consistent you shouldn't have too many.
does it matter what resin i use? which one do you use?
I use Countertop Epoxy for my bottles and anything functional, and Art Resin for anything else
Hi, I was wondering if u had anyone drop the hydroflask and the epoxy broke off with the paint. I saw a video about that and I'm unsure if that will happen to the hydroflasks. Anywho thank u for the tutorial!!
It really depends on how it lands. I've dropped mine onto the road from my lifted truck and It's been fine. But unfortunately resin is not indestructible so if the bottle gets dented it will likely crack or chip.
Thank you for this video, it’s been very helpful! Do you apply a second coat or is one coat sufficient?
It depends on how the first coat cures, but usually 2 coats makes it a lot more durable
Can u make a video on how u do cut the bottom bubbles of epoxy off pls
I do actually have a video up already showing how I do this on a coffee mug, which it's basically the same as what you'd do for one of these bottles.
Thank u I appreciate it
Links to resin supply?
It's Premium FX Poxy by Countertop Epoxy
Hey I’ve been watching this video for a while and I’ve actually started to customize my own bottles, but I run into one problem that keeps reoccurring. Whenever I try to coat my bottles and resin when they’re fully cared it starts to shrink towards the top of the bottle and it creates these shrinkage lines. Now, I don’t know if it’s the type of resin then I’m using but I’m going to try switching to the one that you’re using because it seems to work very well but if you have any tips or know why it’s doing this please respond back to me!
I have never experienced that issue myself. It sounds very strange. To me it sounds like it's probably the resin, or possible the temperature in the area that you're doing it. Resin is very sensitive and works best at temperatures around 70-75, it also does not do well in humidity. Hopefully this helps, sorry for my delayed response I had a baby a few months ago.
@@bexxfineart2268 oh no problem! I figured it was the temperature I had it at, thank you for the response and I hope you and your new family are doing well 🙂❤️
hello how did you prep the bottles before adding the epoxy?
If you mean after I've finished painting I don't do anything I just put the resin right over the top of the painting.
How do u do the bottom?
I have a different video showing how I cut drips off the bottom when needed
Where do you buy that size and brand epoxy? Thank u!
Its called countertop epoxy. You can only get it through their website.
@@bexxfineart2268 ok thank u!
@@bexxfineart2268 you make it look so easy! I used art Resin and have bumby areas. Did i not mix it well? Does Countertop epoxy work better for this purpose?
@@iitsMissy it definitely takes practice to get it perfect. Some resins gave more bubbles than others, but you definitely have to use a heat cut or a blow dryer at the very least to pop the bubbles. Wait about 15 minutes after you put the resin on the surface then use one of those tools to gently pop them. A lot of artists use blow torches as well as a super easy way to pop bubbles.
@@bexxfineart2268 ok thank you! Its not the bubbles its the leveling.
but you dont show how to get the drips off the bottom????
I have another video that shows how to cut drips off a cup.
The tumblers are gorgeous. Thanks for the video. The music is nice, but as a hearing impaired person I’m having a very difficult time hearing you over the music which is louder than your voice. Please lower the music in future videos for those of us with hearing issues. I’m grateful you didn’t wear the mask bc I was able to do some lip reading. Looking forward to more of your videos. The art is lovely.
Thank you for your feedback, because of your comment I have stopped using music through my tutorials when I'm speaking or have kept it extremely low so it's not as distracting.
I noticed you don't wear a mask... is that epoxy non toxic?
I didnt wear a mask in this video so that way I could give clear directions and explanations. But yes the resin I use is 100% non toxic, however I still always wear a mask.
She went over this...
please turn the music down, hearing you is more important, than the background which is drowning your voice out.
Can't hear you over the unnecessary music. Thanks for sharing!
Had to turn off because the music was interfering with your voice
So it takes you over 10 minutes to say you use your finger.
Can you use mod podge?
You can use whatever sealer you personally thinks best. I would recommend testing it out before putting it on a bottle though. The reason I use resin, is because it's durable, doesn't yellow like other sealers, and can withstand a good amount of heat.
The music is very distracting
Pour out the thicker one or it will likely not get mixed in properly because it will be stuck to the sides and bottom... amateur move
I make sure to scrape the edges of the cup and the popsicle stick frequently, as directions state for mixing every resin. I haven't had any issues in the 4 years I've been using it🤷🏼♀️ But this is something I should have elaborated on for newbies to resin, so thank you.
Too much taking about irrelevant things, time wasted
Can I apply resin on the glass bottles that I paint with acrylic paints??....also how do I avoid the dripping of resin as I'm not well versed with cutting the excess..