Can it be repaired Astra H Z16XEP twinport manifold Part 1
HTML-код
- Опубликовано: 9 янв 2020
- In this episode we start the rather lengthy repair of the lower inlet manifold on the Astra twinport
Music Credits
Intro/Outro Track
Syn Cole - Feel Good [NCS Release]
Music provided by NoCopyrightSounds.
Watch: • Syn Cole - Feel Good |...
Free Download / ncs.io/feelgood
Hy my friend, great job and well done, how much kilometers the car have? I am interested when this problem appears and after how many kilometers? Thanks for the video and we aspect another video with the great job that you can do, please make in description always the parts that you are using...
Hi, the original engine had about 123,000 miles which equals approximately 193,000 km however there were signs that it has had a new intake manifold at some point and I think the blocked exhaust gas channels have a lot to do with poor maintenance, looking at the amount of carbon build up in the engine in general I don't think the oil was changed that often
Hi 👋 I had a problem with that but I removed all, flaps to and closed the holes! Work fine for now 😬
Pozdrav druže kakvi su ti bili simptomi na vozilu kad su crkle klapne?
Da li je izbacivao grešku ili je imao problem pri oduzimanju gasa da cima
Hvala !
Pa meni je prijavljivao gresku pa kad sam skinuo pola ih bilo blokirali na otvoreno ili zatvoreno pa sam ih zacepio i izbacio ove ostale dijelove!
Gledam i cudim se kakvu glupost su Nemci napravili..Samo su bez razloga iskomplikovali motor.I kazem sebi-treba sve to povaditi i izbaciti!! I naletim na istomisljenika🙂Jedino nama sa Balkana dolaze ovakve ideje.
Kako motor sada radi?Jel ne pali check engine? Razlika u potrosnji goriva?
Hello
So u remove them and blind holes after them ? Thank you
I have a question, I want to replace the potentiometer, do I have to replace it from below or can I also do it from above?
Which potentiometer are we talking about
About this potentiometer on manifold, but i solve this Problem
Will it work properly if the flaps are open all the time ?
The twinport system on these engines is designed to improve lower speed torque and fuel economy, Vauxhall/Opel/GM fitted the system for a reason so although the engine will run without the valves/flaps fitted I wouldn't recommend removing them, it will effect the performance of the engine as it will have been mapped to include the changes in airflow caused by the twinport system, also if you removed the control valve and position sensor you will more than likely get the engine management light on all the time
how can i contact you sir? i have same engine and i want to ask you some questions because i have removed the lower manifold, i've cleaned it and now the engine is not running that well and twinport not working anymore.
Hi, thanks for your comment, I think my email address is available through my RUclips channel however I am not a qualified mechanic and don't work in the motor trade, just a keen, and fairly experienced DIYer 😊, I'm always happy to help if I can but I can only really discuss and comment on problems I have encountered or fixed myself, Sorry
I have done the exact samr thing as in your video but still have no low end torque ...cound the actuator be broken?
its possible, I didn't have any real drop in performance, just the rattle/knock which as you will see in later videos, turned out to be a lot worse
@@vauxrez8831 i now don't think its the actuator fault as i feel a surge of power when reaching 3000 rpm. Which indicates the actuator and the system is working....so I'll look somewhere else. I suspect the throttle position sensor. (I'm writing this for anyone who still has a hard time finding the problem)
What is the bearing dimensions and code you use?
Unfortunately the seller I bought the bearings from is no longer listed on eBay, however the type/size of bearing I used was MR85ZZ 5MM X 8MM X 2.5MM
Below is a link to a different seller who has this size listed, I hope this helps
www.ebay.co.uk/itm/MINIATURE-REMOTE-CONTROL-MODEL-BEARINGS-CHOOSE-SIZE-AND-PACK-QUANTITY/123866045901?hash=item1cd6fdddcd:m:m7WrOBREjSPoy2-BwpVD_nQ
@@vauxrez8831 thanks
Can you send the link for those bearings please
Unfortunately the seller I bought the bearings from is no longer listed on eBay, however the type/size of bearing I used was MR85ZZ 5MM X 8MM X 2.5MM
Below is a link to a different seller who has this size listed, I hope this helps
www.ebay.co.uk/itm/MINIATURE-REMOTE-CONTROL-MODEL-BEARINGS-CHOOSE-SIZE-AND-PACK-QUANTITY/123866045901?hash=item1cd6fdddcd:m:m7WrOBREjSPoy2-BwpVD_nQ
Hy my friend, great job and well done, how much kilometers the car have? I am interested when this problem appears, after how many kilometers....? Thanks and we aspect another video with the great job that you do, please make in description always the parts that you use.
What's the ball on the side? I need that part.
its the vacuum actuator that operates the flaps
@@vauxrez8831 Thank you very much
This is such a useful video, I've got this exact engine and I've been spending months trying to trawl around it to find what's wrong with it. Thanks a lot for this.
Edit: I was wondering if you have a link for a supplier that supplies the swirl flap arm
Hi, thanks for your comment, unfortunately I didn't replace the arm so I'm not sure where you would get one from as I'm pretty sure Vauxhall/Opel only supply the complete manifold, you could try a breakers yard but they will probably want to sell you the complete unit too
Hi. I wanted to contact VauxRez by email or telephone ? is this possible
Vectra 1.6 from 1997 was the best engine without that shitty twinport :(
So much sensors and other junk on that engine that fails for only 5 horsepower more...
I removed Egr valve and the twinport nd it runs better than new.
Even more milage per liter.
Hello mate
How did u remove that twinport ? Thank you :)