The voltage and current at the LED terminals won't possibly harm you as they are downsized by the circuitry. Of course, any electric work is inherently dangerous and a warning was appropriate.
@@gopalakrishnanmsYou willing to bet your life on that? First, they're wired in series.10 LEDs equals about 35V. The current is enough to kill you... takes hardly any. More to the point, we don't know why the unit failed. Maybe the voltage is too high. Lastly, as I said, they're wired in series. The foil bridge has little resistance, which means the voltage for 10 is now divided between 9 LEDs. They'll run hotter. If they cause a fire and that modification is discovered, your insurance claim will be refused. You could kill yourself or worse, someone else.
You forgot to mention that the LEDs inside the lamp is at HIGH mains voltage (depending on lamp design) since there uis no galvanic isolation and pose a SERIOUS risk should you inadvertantly touch any of the components on the PCB. Do not try this at home!
That sounds interesting! What's the purpose of pouring glue on aluminum foil? Is it to create a new super adhesive or just to test the glue's features?
@@maricarmenjordantorrent7575I'll bet they haven't caused a fire either... yet. LEDs are meant to last a very long time, so there's a good chance there's a fault in the circuitry, then you add 10% more voltage to each led. If they cause a fire and the modification is discovered, your insurance claim will be refused.
Soldering a decent sized wire in place of the dead LED would make a much better contact than gluing aluminum foil across the contacts. You might get an intermittent connection and arcing. Replacing the LED would be the best. Keep a donor bulb to fix others that fail.
Thank you Creativeholic for this handy video. Thank you to the Community Members who also provided useful information as well. Best Wishes to all of you!
Do not solely rely on the switch before starting to remove the LED. Most of the switches cut the current on one line, therefore if you connect the switched line to Neutral (you have 50% of chance) then the live line will not be interrupted and you may get a shock when you touch the burned LED (depending on the position of the LED on the LED string, especially if it's close to the high voltage side) with a conductive tool. Totally unplugging the system from the mains is the best choice.
Better way to do #2, just fill the existing hole with superglue, let it sit overnight & screw the hinge back in place. The fiberboard will absorb some of the superglue, the rest will harden in place, and you'll have a small dimple in the center where the screw goes. For hardwood doors, use superglue or wood glue and a toothpick or small diameter dowel.
"use superglue or wood glue and a toothpick or small diameter dowel" .....and go the added effort of centering the holes. That hinge isn't going to re-install properly.
On #2, you could have just stuck toothpicks in the original holes and screwed everything back in place. The screws create new threads in the toothpick as you screw it down. Much easier than what was shown here.
Some interesting ideas. I’m not sure I’d take the time to deal with an LED bulb like that though. It was still a “shaky” lightbulb. That would drive me crazy.
Please don't take this personally, but number 4 is one of the worst ideas I've seen. It is dangerous, for two reasons. First, you never work on anything while it is plugged in. You should edit the video to put a warning message about that, immediately. 4:04 Secondly, if one led can stop the rest of the leds lighting up, that means they are wired in series. This in turn means that each of the ten leds gets the right voltage ONLY when there are ten of them. Leaving only nine means each one is getting about 10% higher voltage. They'll run hotter. They could cause a fire. If they do, and the fire department finds your led bulb, and can see the modification you made, your insurance won't pay out. That's a good outcome... a bad outcome is you kill yourself... a devastating outcome is you kill others. Yep, number 4 is a very, very bad idea.
سلام از ایدههای شما استفاده میکنم و بسیار علاقهمندم من این روش را تجربه کردم و عمر لامپ بعد از تعمیر کمتر از ۷ روز مجدد میسوزه،ولی این روش برای لامپهای بالاتر از ۲۰ وات بسیار مفید و عمر لامپ طولانیتر است. موفق باشید💐
"Wow, this video blew my mind! Using aluminum foil and super glue to fix various items is such a genius idea. I never thought these everyday materials could be so versatile. Can't wait to try out these hacks myself!"
Molto interessanti le idee che ci hai consigliato e possono ottenere!. risparmiando, riuscendo, aggiustando, con il fai da te: con le nostre mani dà molte soddisfazioni gratificazioni!. Io sono dell'Italia centrale🇮🇹 sul Mar Adriatico Buon lavoro idee, ai prossimi video Buone Sante Festività!.
That loose illumination LED didn't necessarily need to be removed. A quick dab on either side with a drop of new solder would have gave it new life, if it was loose due to insufficient solder.
❤sizin bilgilerden çok yararlanıyorum bazı bilgilerden bende çkk büyük fikirler çoğalıyor umut ediyorumki bu bilgi çeşitliluğinden daha fazla atılımlar göstereceğim başarılarınız daim olsun eğitimsisteminiz güzeliklerle dolsun saygılarımla
Great....and aluminum tape is my personal god of cheap fix great strength and best if two or three layers are used, small wrinkles are like ribs of strength
If you wish to clean Silver Jewlery or Silver plated utensils, put Aluminium foil in a basin, pour in hot water that has Sodium Bicarbonate dissolved in it & then put the Silver objects in so they touch the Aluminium. Wow! they clean immediately as they touch the foil.
Since you had a soldering iron as in #6, why didn't you just use that to fix that LED bulb? A single drop of solder bridging the pads for that bad LED is all it would need. However gluing a piece of foil over them will result in a poor mechanical connection when the board heats up, and possibly even a high-resistance connection that will heat up and possibly start a fire. Use the right tools and methods for the job.
I clean my aluminum foil with aluminum foil so I can reuse it. When the aluminum foil i use to clean the other aluminum foil gets dirty i take another piece of aluminum foil & use it to clean the aluminum foil that i use to clean the aluminum foil so i can use it again.😊
I see... the aluminum foil with the super glue helps you put your hinge on crooked. Nice!
Thanks so much for watching our video. Wish you all the best
I got to a minute 28 and saw that too. No idea what the rest shows...
Great hacks except for #4 which is downright dangerous.
Hello! thanks for your comment. Wish you all the best!
You mean you don't do electrical work on stuff that's plugged into an active source? What could possibly go wrong? 😅
The voltage and current at the LED terminals won't possibly harm you as they are downsized by the circuitry. Of course, any electric work is inherently dangerous and a warning was appropriate.
I like this no. 4th to try
@@gopalakrishnanmsYou willing to bet your life on that?
First, they're wired in series.10 LEDs equals about 35V. The current is enough to kill you... takes hardly any.
More to the point, we don't know why the unit failed. Maybe the voltage is too high.
Lastly, as I said, they're wired in series. The foil bridge has little resistance, which means the voltage for 10 is now divided between 9 LEDs. They'll run hotter. If they cause a fire and that modification is discovered, your insurance claim will be refused. You could kill yourself or worse, someone else.
You forgot to mention that the LEDs inside the lamp is at HIGH mains voltage (depending on lamp design) since there uis no galvanic isolation and pose a SERIOUS risk should you inadvertantly touch any of the components on the PCB. Do not try this at home!
And as the resistance is lower now, all the other led's will went wrong quickly.
Hello! thanks for your comment. Wish you all the best!
That sounds interesting! What's the purpose of pouring glue on aluminum foil? Is it to create a new super adhesive or just to test the glue's features?
Pour glue on the aluminum foil to create a bond and make it more sturdy
Un led menos recarga los otros. Pronto se quemara la bombilla.
Pues yo he arreglado varias hace meses y siguen funcionando.
@@maricarmenjordantorrent7575I'll bet they haven't caused a fire either... yet.
LEDs are meant to last a very long time, so there's a good chance there's a fault in the circuitry, then you add 10% more voltage to each led.
If they cause a fire and the modification is discovered, your insurance claim will be refused.
Most of them get refused anyways
these days the thieving tapeworm
son's of bitches!
Thank you, very useful tips with things at home. Great when you're in a hurry or for an even elderly woman on their own .
Hello! I am very happy to read your comment. Have a good day!
You are amazing man!
We look forward to teaching you new tricks.
Sincerely yours
from Iran
Thank you! Cheers!
That LED isn't going to last without the proper ohms
Hello! thanks for your comment. Wish you all the best!
Soldering a decent sized wire in place of the dead LED would make a much better contact than gluing aluminum foil across the contacts. You might get an intermittent connection and arcing. Replacing the LED would be the best. Keep a donor bulb to fix others that fail.
@@beku2283 ohms is most important...a decent size wire is too arbitrary and will burn out faster.
Just buy a new one. I hate when people do this
@@anthonybasile5035 🤣🤣🤣
Hola. Saludos desde Medellín-colombia.
Muy interesante los videos. Se aprenden muchos trucos.
Glad it helped!
Gary from Oklahoma USA Thumbs Up!
Welcome to Creation Holic channel! Thanks so much for watching our video. Wish you all the best
De Valladolid, España Adelante. Os vemos con gusto.
Welcome to Creation Holic channel! Hope you have a good time while watching the video
Thank you for all these exemples. With these knowledge i can make a lot of repairing
Glad it was helpful!
Good video prayers for you and yours
Thank you so much 🤗
For number 2 use a few toothpicks and a bit of wood glue or even simple white glue.
I agree...toothpicks are a zillion time faster n easier than all those steps!
Hello! thanks for your recommendation. Wish you all the best!
Saw-dust mixed with woodglue using a dowel or toothpick. Keep your saw dust and wood-chips for these repairs.
*I use UV cure glue and clear food wrap and stuff it in the hole. Light it up with UV flashlight for 5 seconds and its ready for screws.*
Thank you Creativeholic for this handy video. Thank you to the Community Members who also provided useful information as well. Best Wishes to all of you!
Hello! Welcome to Creation Holic channel. I am very happy to read your comment. Have a good day!
Muy buen vídeo repleto de excelentes ideas, gracias por compartir.
Hello! I am glad you like this ideas. Wishing you all good things!
Thanx for your great tips.
Glad you like them!
잘 봤습니다 😊👍
Glad you like them!
You did not just risked yourself and taught kids to risk themselves getting electrocuted to smithereens to save $2 bucks ? Dude.
I think it's quite simple
Yeah it's simple... you disconnect the power before doing any work on mains powered equipment.
いいもの観ちゃった！
ありがとう！
Thank you so much for your positive feedback! I'm glad you enjoyed the video and found it helpful
Your ingenuity is purposeful and boundless!!! Keep it up!!! Genius and waste not want not are always appreciated!!! Robert W Goodwin MD aka Db
Thanks so much for watching our video. Wish you all the best
شكرا لك على هذا الفيديو المفيد انا من الجزائر
Thank you so much for your positive feedback! I'm glad you enjoyed the video and found it helpful
Do not solely rely on the switch before starting to remove the LED. Most of the switches cut the current on one line, therefore if you connect the switched line to Neutral (you have 50% of chance) then the live line will not be interrupted and you may get a shock when you touch the burned LED (depending on the position of the LED on the LED string, especially if it's close to the high voltage side) with a conductive tool. Totally unplugging the system from the mains is the best choice.
Hello! thanks for your comment. Wish you all the best!
I have benefited a lot from these videos, thank you
Glad it helped!
Better way to do #2, just fill the existing hole with superglue, let it sit overnight & screw the hinge back in place. The fiberboard will absorb some of the superglue, the rest will harden in place, and you'll have a small dimple in the center where the screw goes. For hardwood doors, use superglue or wood glue and a toothpick or small diameter dowel.
Hello! thanks for your comment. Wish you all the best!
wood glue + sawdust 👍 = best
"use superglue or wood glue and a toothpick or small diameter dowel" .....and go the added effort of centering the holes. That hinge isn't going to re-install properly.
Thanks you😊
#2 was crooked due to poor alignment. I would rather follow your advise, than videos as holes are not enlarged and easier to aim at
Good tips👍 Greetings from Venice Italy
Welcome to Creation Holic channel! Thanks so much for watching our video. Wish you all the best
Way cool stuff!! Thanks!
Glad you liked it!
Desde España. Muy buenos trucos. Muy útiles. 😊
Glad you like them!
素晴らしいアイデアです👏👏👏👏👏
Thank you! Cheers!
Xalapa Ver. México, tu canal es muy bueno. Gracias por compartir tantos tips. Feliz año nuevo.
Thank you, wish you a happy and joyful new year
great video!
Thanks for the visit
Hello from Switzerland greetings😊
Thanks for coming
Using staples is a great idea!
Welcome to Creation Holic channel! Thanks so much for watching our video. Wish you all the best
Thanks for your ideas. It is very useful for me. I'm from Ukraine.
Glad it was helpful!
Thans for sharing.
"Hello! Welcome to Creation Holic channel! I am glad you like this ideas. Wishing you all good things!
"
On #2, you could have just stuck toothpicks in the original holes and screwed everything back in place. The screws create new threads in the toothpick as you screw it down. Much easier than what was shown here.
Hello! thanks for your recommendation. Wish you all the best!
بنده از ایران بیننده برنامههای آموزنده شما هستم
بسیار عالی و آموزنده
Hello! Welcome to Creation Holic channel. I am very happy to read your comment. Have a good day!
Some interesting ideas. I’m not sure I’d take the time to deal with an LED bulb like that though. It was still a “shaky” lightbulb. That would drive me crazy.
I understand your concern! Make sure you have safety equipment in place before doing so
@@creationholic101😊😊😊😊😊 il 😂😅 mi
7😊😅 hu 😅 hu tu 😊
.y numuku Lloyd's KK o se la ok look 9!😊😊😊
Ma oggi nn
😅🎉😅😅😅u. G
Y😅😅 MM😢o II.
@@creationholic101😅😅😅😅😅😅😮 fammi II pollo pollo solo se nn
Buon
😮
Lo lum in😊😊un u in
Its only by camera rekord, not visible blinking for eye
Thank you, my friend, and I wish you good luck and success
Thank you too
Hello!! thanks!! From Seville, Spain
Welcome to Creation Holic channel! Hope you have a good time while watching the video
Good time, teacher, your works are really beautiful 💖🤌👍🌹 and unique 💖💖
Thank you! Cheers!
Thanks for the tip
Thank you! Cheers!
I'm from Vietnam 😊
Welcome to Creation Holic channel! Hope you have a good time while watching the video
Australia. Hello to you...
Welcome to Creation Holic channel! Thanks so much for watching our video. Wish you all the best
This is someone who loves AU foil!
I think anyone would love gold foil. Alum8nium is Al.
AU is the atomic symbol for gold. AL is the atomic symbol for aluminum.
Bombaaaa very good man Thank You Very Much🙂
Thank you so much for your positive feedback! I'm glad you enjoyed the video and found it helpful
I'm from Elyria oh. Very interesting skills
Thanks and welcome
Ciao, ho guardato il tuo video dalla Romagna Italia, grazie per avere mostrato come risolvere alcuni problemi.
Hello! Welcome to Creation Holic channel. I am very happy to read your comment. Have a good day!
Please don't take this personally, but number 4 is one of the worst ideas I've seen.
It is dangerous, for two reasons. First, you never work on anything while it is plugged in. You should edit the video to put a warning message about that, immediately. 4:04
Secondly, if one led can stop the rest of the leds lighting up, that means they are wired in series. This in turn means that each of the ten leds gets the right voltage ONLY when there are ten of them. Leaving only nine means each one is getting about 10% higher voltage. They'll run hotter. They could cause a fire. If they do, and the fire department finds your led bulb, and can see the modification you made, your insurance won't pay out. That's a good outcome... a bad outcome is you kill yourself... a devastating outcome is you kill others.
Yep, number 4 is a very, very bad idea.
Hello! thanks for your comment. Wish you all the best!
I'm from Iran❤❤❤❤❤❤❤❤❤❤❤❤❤
Welcome to Creation Holic channel! Thanks so much for watching our video. Wish you all the best
Excellent examples and demonstrations. Very usefull thank you
Thank you so much for your positive feedback! I'm glad you enjoyed the video and found it helpful
Excelente canal me encantan los trucos caseros
Thank you so much for your positive feedback! I'm glad you enjoyed the video and found it helpful
I roll up aluminum foil into a ball to clean the grates in my charcoal grill. Works great.
Great tip!
Thank you very much
Hi. Thanks for visiting my channel. What idea would you like me to do in the next video?
@@creationholic101 anything thank very much
Bonjour de France, et merci!
Welcome to Creation Holic channel! Hope you have a good time while watching the video
A fan!!! USA, HAWAII!!! Db
Thank you for watching
These are good ideas,
Glad you like them!
If the switch at 3:00 min is SPST, you should be at danger... It should be DPST switch. Or you have to disconnect the plug from the main socket.
Hello! thanks for your comment. Wish you all the best!
سلام از ایدههای شما استفاده میکنم و بسیار علاقهمندم
من این روش را تجربه کردم و عمر لامپ بعد از تعمیر کمتر از ۷ روز مجدد میسوزه،ولی این روش برای لامپهای بالاتر از ۲۰ وات بسیار مفید و عمر لامپ طولانیتر است.
موفق باشید💐
Thank you for sharing your feedback. You can weld it for longer life
thank you for sharing this video to view it is very clever ideas I wish this channel more success
Thank you so much!
To the first “tip” - steel wool would do the same job cheaper…😉
Hello! thanks for your recommendation. Wish you all the best!
hi from south Carolina usa
Welcome to Creation Holic channel! Hope you have a good time while watching the video
Thanks! Brazil!
Thank you! Cheers!
"Wow, this video blew my mind! Using aluminum foil and super glue to fix various items is such a genius idea. I never thought these everyday materials could be so versatile. Can't wait to try out these hacks myself!"
Thank you! Cheers!
Thank you much solutions
Happy to help
Molto interessanti le idee che ci hai consigliato e possono ottenere!. risparmiando, riuscendo, aggiustando, con il fai da te: con le nostre mani dà molte soddisfazioni gratificazioni!. Io sono dell'Italia centrale🇮🇹 sul Mar Adriatico Buon lavoro idee, ai prossimi video Buone Sante Festività!.
Hello! Welcome to Creation Holic channel. I am very happy to read your comment. Have a good day!
This guy can fix any thing, wow🎉
Welcome to Creation Holic channel! Thank you so much for your comment! have a nice day!
MacGyver
Nice ❤❤❤
Many many thanks
These diys are what keep me up late at night. I also 'travel' a lot, lol
Glad you like them!
Hmm, I know what you mean man
çok güzel videoların var. Teşekkür ederim.
Thank you so much for your positive feedback! I'm glad you enjoyed the video and found it helpful
Ik kom uit Nederland en kijk graag je filmpjes.
Hello! Welcome to Creation Holic channel. I am very happy to read your comment. Have a good day!
Len from New Jersey USA
Welcome to Creation Holic channel! Thanks so much for watching our video. Wish you all the best
What superglue do you use ?
cyanoacrylate adhesive glue
Also great for cleaning bbq grill, reflecting/directing wifi signal, and emergency auto fuses (good excuse to always have gum in your car.
That's a great idea!
That loose illumination LED didn't necessarily need to be removed. A quick dab on either side with a drop of new solder would have gave it new life, if it was loose due to insufficient solder.
Thank you! Cheers!
❤sizin bilgilerden çok yararlanıyorum bazı bilgilerden bende çkk büyük fikirler çoğalıyor umut ediyorumki bu bilgi çeşitliluğinden daha fazla atılımlar göstereceğim başarılarınız daim olsun eğitimsisteminiz güzeliklerle dolsun saygılarımla
Glad it helped!
"May your education system be filled with beauties" I hope that's Google's misinterpretation and not what you actually said?
Muy buenos tips
Glad you like them!
Your follower from Iraq
Welcome to Creation Holic channel! Hope you have a good time while watching the video
Helo .sài gòn. Vietnam
Welcome to Creation Holic channel! Hope you have a good time while watching the video
I like that LED light cheat❤❤
Thanks so much for watching our video. Wish you all the best
Great....and aluminum tape is my personal god of cheap fix great strength and best if two or three layers are used, small wrinkles are like ribs of strength
Welcome to Creation Holic channel! Thanks so much for watching our video. Wish you all the best
你好我來自台灣，請問陽台的遮雨棚，有破洞要用什麼來修？謝謝你
you can refer to this video
ruclips.net/video/q8JBsNyIgUE/видео.html
Sei un genio ora so qualcosa che prima non sapevo👍💯🤗
Welcome to Creation Holic channel! Thank you so much for your comment! have a nice day!
If you wish to clean Silver Jewlery or Silver plated utensils, put Aluminium foil in a basin, pour in hot water that has Sodium Bicarbonate dissolved in it & then put the Silver objects in so they touch the Aluminium.
Wow! they clean immediately as they touch the foil.
Cleaning silver, gold, with Toothbrush and toothpaste. Top 👍👍
I from Iran❤
Welcome to Creation Holic channel! Hope you have a good time while watching the video
Im afgan its very good
"Hello! Welcome to Creation Holic channel! I am glad you like this ideas. Wishing you all good things!
"
Thanks, thats 6 mins I'll never get back.
Thank you! Cheers!
Cool
❤😮
Welcome to Creation Holic channel! Thank you so much for your support
I use aluminium foil to clean the aluminium engine casings with aluminium cleaner
That's a good idea!
Fantástico, muito bom.
Thank you! Cheers!
Good morning greece
Welcome to Creation Holic channel! Hope you have a good time while watching the video
Those ideas with aluminum are not bad
Thank you! Cheers!
Increible 😅
Thanks so much for watching our video. Wish you all the best
From Greece
Welcome to Creation Holic channel! Hope you have a good time while watching the video
Since you had a soldering iron as in #6, why didn't you just use that to fix that LED bulb? A single drop of solder bridging the pads for that bad LED is all it would need. However gluing a piece of foil over them will result in a poor mechanical connection when the board heats up, and possibly even a high-resistance connection that will heat up and possibly start a fire. Use the right tools and methods for the job.
I want to give more measures to people who don't have a soldering iron
3:14 the failed LED already had a dot on it. 😁
Please try and feel
Rio de Janeiro! Brazil
Welcome to Creation Holic channel! Thanks so much for watching our video. Wish you all the best
Good idea
Many many thanks
Japan😊❤❤❤
Welcome to Creation Holic channel! Thanks so much for watching our video. Wish you all the best
I clean my aluminum foil with aluminum foil so I can reuse it. When the aluminum foil i use to clean the other aluminum foil gets dirty i take another piece of aluminum foil & use it to clean the aluminum foil that i use to clean the aluminum foil so i can use it again.😊
That's such a great idea
From india
Welcome to Creation Holic channel! Thanks so much for watching our video. Wish you all the best