Ignition coils, spark plugs, and pcv valve breathers may need to be checked, as well as a tune up too. Thats what i was educated on with my BMW and I confirmed with a OBD Scan too. Once i addressed and replaced them, it went away and hasnt shown up again. 💯
Can please someone help me i have a 318D gt and this faulty cod is showing up only when i go fast and when i put the obdi scanner its only saying fuil rail pressure sensor and clogged catalig converter some people told me its injector please someone help me thanks
Had this problem today with my 2014 328i. I was driving like normal and all of a sudden, she jerked like crazy and the error showed up.but kept goin. I pulled over stopped the engine, turned it back on. Error was gone. I had a little less than quarter tank of gas. Just as I was getting to the gas station literally stalled in the middle of the intersection about 4 times. Barley made it to the gas pump. After filling her up she was fine. But the problem may be in the gas tank, there are these little floats that measure the gas in the tank. Sometimes one of them gets stuck and won't properly measure the amount of gasoline in the tank. I just ran out of gas. Fuel pump may need to be replaced. Or both fuel pump and gas tank all together. But like you said it could be a hundred other things. Hope this helped love. And I hope you can find what the problem is soon.❤
Clearing them will clear however can't ignore the issue which goes back to the above components you have what's called an intermittent problem soon you will not be Abel to clear the codes until you fix those codes once it's done then yes after turn on car turn off car clear codes drive it for around 20 minutes you'll see that the errors will not re appear
Got a 2013 650xdrive grancoupe get that dam code all the time 😢 it can be anything sparkplug mass air flow sensors fuel pump fuel management motherboard its such bull and everytime it happend my motor starts shaking violently like its going to shake out of the engine bay. Wish i knew
I have a 3 months old 2024 X6M Competition. The vehicle stops for the same drivetrain message. I’m so done with BMW. Going back to a $3000 Honda or Toyota.
That must be frustrating! My issue was plugs and coils.. I doubt it could be the same issue for you 2024 should have No problems! Did you figure out what the issue was ?
The dealer said it was a bad transmission , the car has been returned. I’ve seen lots of the x6 competition up for sale at such a low mileage, I’m assuming the x6 is not a reliable car for the price. @@mrpayola4466
Basically whoever had the car before you did not take care of it, you shouldn't be looking for advice on youtube for smoking coming from your car. Should go straight to mechanic. I have same engine as you in my 2015 328i I'm at almost 80k and it runs fine. Are you putting 93 octane and changing oil every 5k miles ?
I have the same with my F32 435i man, i fixed all oil leaks, cleaned both the vanoses, changed oil (Castrol Full Synsetic W05-30) and still have the problem when i’m accelerate hard. I’m thinking maybe to change the oil pump but it’s expensive and i don’t know if that’s the problem is. Very annoying
Codes 123401 ( electri wastegate learning limits stop malfunction ) and 123432 ( Electronic wastegate learning limits stop: stop position, wastegate position close out of tolerance. ) mechani just shorter the wastegate link from the turbo aprox 1/4 if an inch and no more dravetrain malfunction.
Back to Toyota my friend.I really got headaches with my BMW 2013 x3 xdrive28i 2.0 . Anything will be drive train malfunction between 1000$ to 18,000 dollars…. Mỹ next car back to Toyota….
Had this happen to me in my 2018 x5 xdrive35i. Had low oil pressure resulting in my engine seizing up from letting it warm up. When I returned to my car it was not running and would not start. $18,000 for a new engine.
I have 2014 bmw 4 series msport. I was driving it on the motorway and all of a sudden broke down from 70 to 40 and kept doing it but I realised it only does it when it’s raining 😢 can someone please help
Had the same thing 2 times prior. Once it died on me in standstill traffic with that on- and I got it restarted & it needed a bunch of 💩 to be repaired. Today it came on again- turned it off…. It seems to have gone away. Idk - I’m getting so pissed w this light/message 😭
Ciao Bmw X5 xdrive 40 E I have the same problem now, after one boost , open the light with drive train. I check with mu mechanic told me is air pressure . We chance the sensor the same problem. Wednesday i go to bmw to see what is next , tester and diagnostics. Hope don't be some expensive part.
i had 0 flue tank and the massage came and car stop then i top it up then back to normal ? is that normal bec i didn’t have any flue in the car . that why the car stop and went to safe mode.
Seems like your car went into limp mode after the fuel ran out. After idling the car for 5-10 minutes it may still appear. Once you start driving for a bit the message should go away regarding “ drivechain malfunction “
Guys my n26 is stage 2 with downpipe and charge pipes and it’s only making 260 horse power really confused on the power loss aswell as it has no engine light lmk
I have the same issue and code is charge pressure to high I think it’s boost pressure diverting valve or vacuum leak I didn’t check it yet because I get the message ones a week
I realized BMWs are finicky, if it happened to you every once in awhile you should be ok. Once a week i would be concerned, should bring it to the dealer. Mine had been fine ever since i filmed this video!
Ok so I have a 2015 M4 with about 68k miles and I was driving my car and was backing into my garage and the drivetrain malfunction light came on when I was reversing into my garage so should I be worried? And is it cool to drive it?
Ignition coils, spark plugs, and pcv valve breathers may need to be checked, as well as a tune up too. Thats what i was educated on with my BMW and I confirmed with a OBD Scan too. Once i addressed and replaced them, it went away and hasnt shown up again. 💯
👍
Yea sir got my plugs and coils changed all good to go !
Did your bmw had fuel system pressure code on the ObS ? I’m having this problem
Thank you for an information.
Can please someone help me i have a 318D gt and this faulty cod is showing up only when i go fast and when i put the obdi scanner its only saying fuil rail pressure sensor and clogged catalig converter some people told me its injector please someone help me thanks
Had this problem today with my 2014 328i. I was driving like normal and all of a sudden, she jerked like crazy and the error showed up.but kept goin. I pulled over stopped the engine, turned it back on. Error was gone. I had a little less than quarter tank of gas. Just as I was getting to the gas station literally stalled in the middle of the intersection about 4 times. Barley made it to the gas pump. After filling her up she was fine. But the problem may be in the gas tank, there are these little floats that measure the gas in the tank. Sometimes one of them gets stuck and won't properly measure the amount of gasoline in the tank. I just ran out of gas. Fuel pump may need to be replaced. Or both fuel pump and gas tank all together. But like you said it could be a hundred other things. Hope this helped love. And I hope you can find what the problem is soon.❤
Sorry to hear this happened to you as well. Hopefully we never come across this problem again !
I am having the same issue. Now, the car is on the side of the road. I will fill it up with fuel. Hopefully, It works
This helped me out today. Thankfully I was pulling into the gas station when it happened
@@abdurrahmanarmani2399 spark plugs and coils were the culprit
It happened to me and had to get gas and it away.
Clearing them will clear however can't ignore the issue which goes back to the above components you have what's called an intermittent problem soon you will not be Abel to clear the codes until you fix those codes once it's done then yes after turn on car turn off car clear codes drive it for around 20 minutes you'll see that the errors will not re appear
I got new coil packs so now I have to get vacuum pump and lines which bmw will fix for 2900 hundred dollars
Ckp is the culprit also coils and plugs
Got a 2013 650xdrive grancoupe get that dam code all the time 😢 it can be anything sparkplug mass air flow sensors fuel pump fuel management motherboard its such bull and everytime it happend my motor starts shaking violently like its going to shake out of the engine bay. Wish i knew
Spark plugs & coils were the culprit!
I have a 3 months old 2024 X6M Competition. The vehicle stops for the same drivetrain message. I’m so done with BMW. Going back to a $3000 Honda or Toyota.
That must be frustrating! My issue was plugs and coils.. I doubt it could be the same issue for you 2024 should have No problems! Did you figure out what the issue was ?
The dealer said it was a bad transmission , the car has been returned. I’ve seen lots of the x6 competition up for sale at such a low mileage, I’m assuming the x6 is not a reliable car for the price. @@mrpayola4466
I have a Bmw 320i 2016 with 76k miles on it and it keeps smoking and shaking and when I press the gas it don’t speed up help me plz 😭how to fix it
Basically whoever had the car before you did not take care of it, you shouldn't be looking for advice on youtube for smoking coming from your car. Should go straight to mechanic. I have same engine as you in my 2015 328i I'm at almost 80k and it runs fine. Are you putting 93 octane and changing oil every 5k miles ?
I still have the same thing on my 2013 f30 335i and also there is no power like before it has stage 2 + but runs now like worser then before stock
I have the same with my F32 435i man, i fixed all oil leaks, cleaned both the vanoses, changed oil (Castrol Full Synsetic W05-30) and still have the problem when i’m accelerate hard. I’m thinking maybe to change the oil pump but it’s expensive and i don’t know if that’s the problem is. Very annoying
Codes 123401 ( electri wastegate learning limits stop malfunction ) and 123432 ( Electronic wastegate learning limits stop: stop position, wastegate position close out of tolerance. ) mechani just shorter the wastegate link from the turbo aprox 1/4 if an inch and no more dravetrain malfunction.
Pull coils out 1 by 1. I had one bad one
Back to Toyota my friend.I really got headaches with my BMW 2013 x3 xdrive28i 2.0 . Anything will be drive train malfunction between 1000$ to 18,000 dollars…. Mỹ next car back to Toyota….
Sorry to hear about the bad luck, my brother had the same issues drive train malfunction error, been driving with it like that for a few years now
Had this happen to me in my 2018 x5 xdrive35i. Had low oil pressure resulting in my engine seizing up from letting it warm up. When I returned to my car it was not running and would not start. $18,000 for a new engine.
No warranty from BMW? 😢
Same issues i bring my car to the dealer and they say it will cost me like 25 thousand dollar to get the car fixed
😢😳
That’s crazy
I have 2014 bmw 4 series msport. I was driving it on the motorway and all of a sudden broke down from 70 to 40 and kept doing it but I realised it only does it when it’s raining 😢 can someone please help
Had the same thing 2 times prior. Once it died on me in standstill traffic with that on- and I got it restarted & it needed a bunch of 💩 to be repaired. Today it came on again- turned it off…. It seems to have gone away. Idk - I’m getting so pissed w this light/message 😭
Lexus!!!
I still love bmw 😩 i hope your car is driving much better now !
Maybe will help some1, i have f30 320i bmw and had this problem draintrain. It was because dpf had reached its lifetime (was never replaced 250 000km)
02 sensors was my problem
Really?
Ciao
Bmw X5 xdrive 40 E
I have the same problem now, after one boost , open the light with drive train. I check with mu mechanic told me is air pressure .
We chance the sensor the same problem. Wednesday i go to bmw to see what is next , tester and diagnostics. Hope don't be some expensive part.
Hopefully you only needed a tune up?
Hi what was the problem? I have the same problem like you if you want help thank you
My gearbox locked in park after driving home in limp mode. 2014 428i. Just over 100 000 ks. Starts fine, but transmission locked.
Did you get this problem fixed Or did everything go back to normal afterwards ?
N55 ?
F12 S63
Had ro get new freaking computer
😢
My 750li 2012 drive training malfunction light comes on when I try to punch it for more speed
My issue was plugs & coils, maybe time for a tune up
i had 0 flue tank and the massage came and car stop then i top it up then back to normal ? is that normal bec i didn’t have any flue in the car . that why the car stop and went to safe mode.
Seems like your car went into limp mode after the fuel ran out. After idling the car for 5-10 minutes it may still appear. Once you start driving for a bit the message should go away regarding “ drivechain malfunction “
@@mrpayola4466 yes that was
They are the best criminals. They keep prisons full!
😂
Guys my n26 is stage 2 with downpipe and charge pipes and it’s only making 260 horse power really confused on the power loss aswell as it has no engine light lmk
Hopefully you got it figured out bro
I have the same issue and code is charge pressure to high
I think it’s boost pressure diverting valve or vacuum leak
I didn’t check it yet because I get the message ones a week
I realized BMWs are finicky, if it happened to you every once in awhile you should be ok. Once a week i would be concerned, should bring it to the dealer. Mine had been fine ever since i filmed this video!
@@mrpayola4466 I found the problem
Boost leak
Crank case vent hose was broken sucking to much air
Ok so I have a 2015 M4 with about 68k miles and I was driving my car and was backing into my garage and the drivetrain malfunction light came on when I was reversing into my garage so should I be worried? And is it cool to drive it?
It could be spark plugs and coils
@ def isn’t that dawg but thanks
Today also at me bro... same error..328i f30..😓🙁
Hope you got it fixed bro
@mrpayola4466 yep, was the clutch..now i've done, that error can be 1567 different things
Any updates on the situation bro?
Hasn’t happened since ! 😌
@@mrpayola4466 how do you fix this shit I have this problem
Please help
My car won’t drive properly now only in comfort mode
Does not work when I reset my car
Junk
What if your exhaust smokes
Probably blew you’re turbo
Could be a coolant leak or burning too much oil !
Turbo shaft bearings or fried valve stem seals.
No that’s the high pressure fuel pump. I would 90% guess
Hey did you ever find out what the problem was?
Your video was so helpful my guy 🫣😤 thanks for the insightful help 🙄
Glad it helped!