Your videos have been so encouraging to me. I’ve always been reluctant to service/ repair my power tools,simply because electronics baffle me. I’m a carpenter/ builder by trade and when my electrician starts talking about ,” ohms , watts, amps,..etc,..” my brain fogs over. I see his lips moving but don’t understand a thing he’s talking about. 😳 Your teaching method is great! You makes mistakes and happily show them. It gives carpenters/ anyone like me hope that we can have a go and fix something without blowing it and ourselves up. Good job.
Thanks to your videos, I have fixed my own Dewalt belt sander to replace the lead, fixed a discarded Dewalt reciprocating saw, and fixed a Ryobi orbital sander that someone discarded. I also know that Makita is the brand to get because you can get parts for it. Your work here is greatly appreciated!
I has a similar accident with a Bosch except the chuck too the full impact onto concrete. The case was fine but the gearbox was toast. Luckily, Bosch was offering a non-questions asked 5 year warranty when I purchased it and another tool and as such I got a free replacement. :)
I think they also sell some of the stickers, at least the ones you cut whenever you open one up, the one behind the motor and the 1 2 3 sticker on the speed selector.
Couldn't get a new clamshell for my DC825 Type 10 as they're obsolete, mine had cracked both sides where the lugs on the gearbox are held in place by the casing. I took it apart and super glued it back together two days ago, we'll see if it holds.
Great job, I know people who would have just thrown that out. You're right about crooked stickers 😁, in fact anything askew like shelves, pictures, tiles etc. seems to touch a nerve and I feel compelled to fix it.
That's funny a few weeks ago, I found a dcf886 broken at the handle & ran over (smashing battery holder) on the side of the road at an intersection. I'm sure someone left it on the back of their utility box truckbed or on a trailer fender or something and it fell off after hitting one of the many potholes marking our wonderful Buffalo streets following the winter beating! Looks like it is banged up pretty well but I bet with a new case & a few wire repairs it would go together & work fine. I was tempted to jumper battery wire to a battery to see if it spins or even acknowledges having a battery connected to it at all? Don't want to fry anything electrical that may have broken wires crossed\shorted out, so its just sitting in a bin for possible parts if needed. I have several 886, 887's & an 886 swapped to 3/8" anvil - which is remarkably easy to do, order anvil, open impact(hardest part is getting clip out of 1/4" bit reciever), and change out the anvils, then put back together and use your 3/8ths" impact(or chrome) sockets to fix you vehicle. Always wanted a friction ring anvil gun instead of using the adapters with sockets which rob the power\blows, but didn't want to buy one cause i have 1/2" dcf899 & dcf 921 already, just needed a 3/8ths model. Its so easy to do to. If you want one for sockets do it - bought a newer used 886 for $40 @ pawn shop a couple yrs ago too. 👍🏻👌🏻🛠️🔧🗜️
Dean, after watching your videos i decided to investigate why my impact driver had stopped working. Turns out it has stripped the teeth off of two spur gears ⚙️. After washing it out how much grease should I put back in? Great content as always
Dean i have a B& D bench grinder HD1245 from my dad eho died in 1983..changed the right side wheel..can't get the left side nut slack...any suggestions
I see you only put this video up 1 hour ago and yesterday I just bought a used Black & Decker DR202 Type 1 corded drill for $5 that works and the level bubble plastic is there, but maybe the fluid leaked out and I can't find that replacement part anywhere online maybe I could put fluid in myself and seal it up or you have another idea.
Because it doesn't affect the operation of the tool or the look (as it is hidden inside that lovely new case) - he has many more tools to fix so why spend time on something that does not bring in extra money ? He does clean some tools with dust etc but that one did not look very dirty.
Your videos have been so encouraging to me. I’ve always been reluctant to service/ repair my power tools,simply because electronics baffle me. I’m a carpenter/ builder by trade and when my electrician starts talking about ,” ohms , watts, amps,..etc,..” my brain fogs over. I see his lips moving but don’t understand a thing he’s talking about. 😳 Your teaching method is great! You makes mistakes and happily show them. It gives carpenters/ anyone like me hope that we can have a go and fix something without blowing it and ourselves up. Good job.
Thanks to your videos, I have fixed my own Dewalt belt sander to replace the lead, fixed a discarded Dewalt reciprocating saw, and fixed a Ryobi orbital sander that someone discarded. I also know that Makita is the brand to get because you can get parts for it. Your work here is greatly appreciated!
Dean, thanks so much for your videos! Going to try to diagnose my DeWalt drill tomorrow, thanks to you. I am so thankful for your content.
Quality right down to the sticker attention to detail as always
Good as new. I never cared for the belt clip , I always worried about accidentally scratching furniture setting the tool down.
First thing i remove when i have a new Drill. I simply don't need it because 90% of my work takes place on the ground.
I has a similar accident with a Bosch except the chuck too the full impact onto concrete. The case was fine but the gearbox was toast. Luckily, Bosch was offering a non-questions asked 5 year warranty when I purchased it and another tool and as such I got a free replacement. :)
Always great Dean!!!!!!!
Masterclass, as always. Cheers from Central Otago Dean.
Many thanks!
I think they also sell some of the stickers, at least the ones you cut whenever you open one up, the one behind the motor and the 1 2 3 sticker on the speed selector.
Couldn't get a new clamshell for my DC825 Type 10 as they're obsolete, mine had cracked both sides where the lugs on the gearbox are held in place by the casing. I took it apart and super glued it back together two days ago, we'll see if it holds.
Great job, I know people who would have just thrown that out. You're right about crooked stickers 😁, in fact anything askew like shelves, pictures, tiles etc. seems to touch a nerve and I feel compelled to fix it.
Car number plates are the worst. Especially when they're on a posh car. 😂
If you wanted to go further you could stamp or engrave the year into the new case where the battery goes.
That's funny a few weeks ago, I found a dcf886 broken at the handle & ran over (smashing battery holder) on the side of the road at an intersection. I'm sure someone left it on the back of their utility box truckbed or on a trailer fender or something and it fell off after hitting one of the many potholes marking our wonderful Buffalo streets following the winter beating! Looks like it is banged up pretty well but I bet with a new case & a few wire repairs it would go together & work fine. I was tempted to jumper battery wire to a battery to see if it spins or even acknowledges having a battery connected to it at all? Don't want to fry anything electrical that may have broken wires crossed\shorted out, so its just sitting in a bin for possible parts if needed. I have several 886, 887's & an 886 swapped to 3/8" anvil - which is remarkably easy to do, order anvil, open impact(hardest part is getting clip out of 1/4" bit reciever), and change out the anvils, then put back together and use your 3/8ths" impact(or chrome) sockets to fix you vehicle. Always wanted a friction ring anvil gun instead of using the adapters with sockets which rob the power\blows, but didn't want to buy one cause i have 1/2" dcf899 & dcf 921 already, just needed a 3/8ths model. Its so easy to do to. If you want one for sockets do it - bought a newer used 886 for $40 @ pawn shop a couple yrs ago too. 👍🏻👌🏻🛠️🔧🗜️
I must say I did chuckle at the crooked label comment. That would've driven me nuts 😂
Dean, after watching your videos i decided to investigate why my impact driver had stopped working. Turns out it has stripped the teeth off of two spur gears ⚙️. After washing it out how much grease should I put back in? Great content as always
Only a few pea sized amounts. They take very little grease
I really like your screwdriver the one that you can switch to both sides and have you done this repair before
done this many times before.
the screwdriver bits are Wiha, they sent this set in to test out a few months ago. brilliant bit of kit
I did a 12v dewalt case replacement was pretty easy and satisfying
Where do they sell the 12v cases?
@@marvin.710 ereplacementparts. mine was a DCD710
Dean where did you buy that double-sided tape I have tried a good few places and can't find that
Bende de 887 p2 var çok kaliteli ve ucuz
Do you repair multimeters ? I have a fluke 77 series 2 that’s playing up
Dean i have a B& D bench grinder HD1245 from my dad eho died in 1983..changed the right side wheel..can't get the left side nut slack...any suggestions
I see you only put this video up 1 hour ago and yesterday I just bought a used Black & Decker DR202 Type 1 corded drill for $5 that works and the level bubble plastic is there, but maybe the fluid leaked out and I can't find that replacement part anywhere online maybe I could put fluid in myself and seal it up or you have another idea.
What type of double sided tape is that?
its simply a standard brand call mammoth tape
👏👏👍
Crooked sticker would ruin the tool completely 😂
Bin mit der Arbeit nicht zufrieden. Warum lässt man den ganzen Dreck am Getriebe und den Kabeln?
Because it doesn't affect the operation of the tool or the look (as it is hidden inside that lovely new case) - he has many more tools to fix so why spend time on something that does not bring in extra money ? He does clean some tools with dust etc but that one did not look very dirty.
Hi,
Have a dewalt drill can i send you an email with photos and let me know if u can repair it or not?
Regards
😂😂😂😂
Good ol' zipties.
new old tool