How to Replace Front Ball Joints 2008-16 Chrysler Town & Country
HTML-код
- Опубликовано: 6 сен 2024
- Buy Now!
New Ball Joint from 1AAuto.com 1aau.to/ia/1ASB...
Modern suspensions combine a number of moving parts for safe and stable handling. The ball joint is the crucial moving component that ties those parts together. The ball-in-socket joint can wear out and loosen over time. Or, the rubber protective boot can tear, allowing contaminants to seize the joint. Bad ball joints are a common failure point on vehicle inspections because they lead to unsafe driving conditions. Fortunately, they are relatively easy to replace with the right know-how. This video shows you how to install new, quality TRQ ball joints on your 2008-16 Chrysler Town & Country.
• Check here for more videos on the 2008-16 Chrysler Town & Country • Chrysler Town & Countr...
This process should be similar on the following vehicles:
2008 Chrysler Town & Country
2009 Chrysler Town & Country
2010 Chrysler Town & Country
2011 Chrysler Town & Country
2012 Chrysler Town & Country
2013 Chrysler Town & Country
2014 Chrysler Town & Country
2015 Chrysler Town & Country
2016 Chrysler Town & Country
Tools you will need:
• 21mm wrench
• 10mm Socket 1aau.to/oa/1AXA...
• 18mm Socket 1aau.to/oa/1AXA...
• 19mm Socket 1aau.to/oa/1AXA...
• 21mm Socket 1aau.to/oa/1AXA...
• 32mm Socket 1aau.to/oa/1AAS...
• Ball Joint Press
• Brake Caliper Hanger 1aau.to/oa/1AXA...
• Pickle Fork
• Snap Ring Pliers
• Straight Cutters
• 1/2 Inch Air Impact Gun 1aau.to/oa/1AXA...
• Ratchet 1aau.to/oa/1AXA...
• Socket Extensions 1aau.to/oa/1AXA...
• Torque Wrench 1aau.to/oa/1AXA...
• Cotter Pin
• Liquid Thread Locker
• Rust Penetrant
• Safety Glasses 1aau.to/oa/1AXA...
• Center Punch 1aau.to/oa/1AXA...
• Hammer 1aau.to/oa/1AXA...
• Sledge Hammer 1aau.to/oa/1AXA...
• Wire Brush 1aau.to/oa/1AXA...
Subscribe: / @trq
Check out our playlist:
Chrysler Town & Country 2008-16 5th Gen: • Chrysler Town & Countr...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
![Megan Thee Stallion - Neva Play (feat. RM) [Official Video]](http://i.ytimg.com/vi/TpYTyAaTRts/mqdefault.jpg)
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts
√ *Do it Yourself*
√ *Save Money*
At first he started to remove the old ball joint with his press only to realize that he hadn’t removed the snap ring and the camera stopped filming and went back to him finally getting the ball joint out
Good eye, Robert! You can see the snap ring still in there while he's attempting to press it out. He should have mentioned that.
My buddy wanted me to watch this, he's going to try to tackle this. 3rd things... 1 make shure there is no snapping before removing, 2 some ball joints come with washers and some don't most times depends on manufacturer. The one in the video should have had a washer installed. If the cotter pin cannot stop rotation of the nut it won't. The washer will move the nut further up the threads to the spot where the cotter pin can have full engagement with the nut. 3 check your own lugnut torque for your wheels most are 115foot lb
By far the BEST how to video on this subject for the Caravan.
Best Dang Mechanic on RUclips.......saving us hundreds! Thank Again:-)
Good video but only one problem? The van He is working on it looks new and clean. Most vans by the time you end up doing this are rusted and not that easy to work on it but instructions are good.
Just so you are aware 20 ft lbs is not enough torque on the ball joint . You are supposed to do another 180 degree turn after torque of 20 foot pounds is met.
Also on the strut bolts you torqued those to 65 foot pounds but then you are supposed to do 90 more degrees after torque is met.
Not properly tightening these could be an issue so in the future you’ll want to get these tight .
What a great detailed instructional video, great job. Instructor is very easy to understand. Others should watch this and learn how to make a video
Excellent how to video, clear and concise!
Thank you very much. Took u less than 15 minutes. Great job 👍.
Be really helpful if these videos would show if we need to press WITH the boot attached or if we take it off THEN press.
Every single video I’ve watched doesn’t talk about this!!
Thank you ver y much for your help, your video was really helpful and saved me a substantial amount of money. Forever grateful
U are a good mechanic and a good teacher and u gose set by set u good
Good video.You're the very professional. Thanks!
Can’t get that ball joint bolt to come loose. Grrrrrr
You dont need to cut the ball joint with the grinder, you can use the same tool to remove the whole thing
I was doing the balljoint on my 08 town and country, and 4 hours later hadn't moved finally cut it, less than a minute job. And I had a balljoint tool, it had messed up the threads on the tool due too not just cutting the balljoint. So while it may not be needed I would recommend it..
Great video. Very professional.
It would of been even better video if you did it slower and maybe explained what to do if it doesn’t work so nicely as yours did the whole way!! I’ve been struggling for days, finally got the old ball joint off but don’t have enough clearance for my tool to push the new one into place.
After all I’m just a lady, with NO lift…lol:
Trying to do it Myself cuz I ain’t got a man to help me and sick of my mechanic messing it up more and cost me a bunch of money lol
Hi you are too good and youm make this very easy nice ty
Are these TRQ ball joints any good?
Replacing the entire control arm with ball joint dies not require me to remove the knuckle does it?
No need to cut the ball joint when you can just use the removal tool with the hole in the center to press it out
You didn't grease the joint. Did it come pre greased?
Will this work on a 2004 caravan
@TRQ do you know if those lower ball joint work on a Chrysler 04 Sebring sedan ?
thank you for help
+carlos banegas Thanks for watching. Buy the part in this video on 1AAuto.com: 1aau.to/m/Shop-TRQ
safety glasses on of course LOL
Exelent video.👌How many hours did you take to do the job?
Probably 30 minutes for both sides.
@@chocolatesmoney8082 would not count on those numbers unless you did it every day in and out...
That’s doing it the hard way.
Did you really say bonk?
the mind is willing ..... the body is Not . Just cause u know How , doesn't mean you should . So my local mechanic has a new job to do .