Mahlkönig E65S GbW | Maintenance cleaning
HTML-код
- Опубликовано: 8 сен 2024
- WARNING:
The instructions shown in this video are meant to support qualified technicians and trained staff, only. Only parts that comply with the original appliance specification may be used for repairs. Mistakes in opening or assembling the machine may cause injuries and/or damages and malfunctions.
If the machine gets opened by an un-authorized person, the manufacturer’s liability and warranty expire.
WARNUNG:
Die in diesem Video dargestellte Anleitung richtet sich ausschließlich an qualifizierte Techniker und geschultes Fachpersonal. Fehler beim Öffnen oder Montieren der Maschine können zu Verletzungen und/oder Beschädigungen und Fehlfunktionen führen. Bei Reparaturen dürfen nur Teile verwendet werden, die den ursprünglichen Gerätedaten entsprechen.
Mit dem Öffnen der Maschine durch eine nicht autorisierte Person, erlöschen die Haftungs- und Garantieansprüche gegenüber dem Hersteller.
Hemro International AG
Länggenstrasse 34
8184 Bachenbülach
Switzerland
Phone: +41 44 864 18 00
Fax: +41 44 864 18 01
E-mail: info@hemrogroup.com
Homepage: www.mahlkoenig.de
I have the rubber flapper with steel thing. How kt shoukd be insert. Rubber flapper first and steel thing behind it? Thanks 3:31
the metal thing should be closer to the burrs, the silicon flapper should be facing outwards, to the exit of the grinder. The metal is supporting the flapper (therefore behind the flapper) to break the clumps. Hope that helps
@@Vagkoul thank you 🙏
There is one highly misleading mistake: The adjustment ring is taken off in a far right position (2:05) while it is mounted back in a far left position (3:20) . This should in practice lead to impractical coarse grind settings - when following blindly. In general I like all the clear explanatory videos and to me they were mostly extremely helpful.
Thank you for the feedback.
This looks like the dream grinder for home use. Is a smaller hopper available for under home kitchen cabinets (under a counter)?
Yes there is. Definitely recommended for home use.
Yes, it is! www.mahlkoenig.com/products/e65s-e80s-bean-hopper-small
Perfect! 👌
Has the zero point (Nullpunkt) to be set a new after cleaning? I think it should stay the same as before the cleaning, right?
Yes, exactly. The zero point should not change after cleaning.
Good video, slightly confusing though, probably the edit.
When releasing the adjustment ring the shot from above shows that it’s in the middle, then when it’s taken off it’s turned from finest to coarsest (0 to 8).
Then putting it back on to align it with the marker 0 position again, next shot from above is in the middle.
Now that’s where it gets interesting. Took it apart, put it back exactly as it was, didn’t change or turn a thing. In 0 position the grind is extremely coarse, it shows on the screen as well how open the blades are.
Any ideas what could have gone wrong?
@@MahlkoenigGrinders you didn’t seem to remove the grind adjustment ring at the zero point (you removed it at a courser setting) but you put it back on at the zero point marker.. This’ll throw the calibration out in terms of the zero point in relation to the number scale and thus it’ll be much courser at the zero point now than it originally would’ve been. It would’ve been fine if the grinder was 're-zeroed' afterwards but that wasn’t shown in this video. We’re trying to use these videos as a tool for the less experienced baristas in the cafe that I work at and sometimes in this instance this would cause miscalibration and even more confusion..
How often should this be done and how often flapper needs be replaced, please? I pull 4, 5 espressos a day. :)
We recommend 800-1250 kilos but will depend on the roast of coffee you use.
Great video! Thank you for sharing! do you know how to update the E65S GbW software? I heard there is a new firmware version.
We recommend speaking to your local Mahlkonig dealer. please see the dealer section of our website to locate. Thank you
If u are home barista there's no point to update lol😂😂
My E68S grinder stalls after one espresso grind. How do I fix it. Its less than a year old.
We would recommend a deep clean and also inspect the burrs. If you are still having issues please contact a local engineer for assistance. Thank you