Extremely useful, used the video to strip down my printer to get at a displaced paper guide. a couple of points: at 1:07 you say you can just disconnect the cable into the front panel. If you just pull it out it actually comes out of the socket at an angle which may damage the connector. The top edge of the front panel easily pops off and gives direct access to the connector so the cable can be removed without stress. You have to remove this edge piece anyway to reconnect that cable. Also at 2:54 you ease off the casing but you haven't mentioned removing the two deep screws at the front. It won't come off without those removed. Excellent and helpful video, saved me buying a new printer!
Top tip; I had to reseat a pressure plate (5 off white plastic bits to right of cartridge run at 3:07 ) each plate holds a small black pressure roller and is spring loaded against the main paper transport roller. The small rollers are clipped into the plastic part but not very securely so, as you wrestle with the spring and the plate, it pops out and you have to start again. I found that the roller could be tied into the plate with a thin wire or thread which can be cut and removed after all the parts are located. Makes life easier.
Fantastic. Not my model but the suggestion to go to your website was greatly appreciated. My 3-in-1 device WF-7250 had a broken hinge. aaaaaaai was able to find a replacement easily on AliExpress.
epson has bad warranty support so i have to fix error 100016 or whatever which is a scanner error that grinds and this is helpful thank you . gotta fix my epscam now
Hi Kevin thanks for this great video. My 7710 will not feed paper completely. It makes a load popping noise then feeds paper halfway. It will feed regular printer paper but no other type of paper. Also it says it's jammed but it's not. Can you point me in the right direction? Thanks again for the videos they a re a big help.
Hey Kevin can you tell me why my 7720 keeps giving me a out of paper on Cassette 1 error??? There's plenty of paper in it and epson couldn't figure it out, it's practically brand new I've had it for 3 years and I only used it literally a few times I never left ink cartridges inside when it's not in use.
Kevin, I went to BCH to purchase the workflow for the WF-7710 WF-7720 and did not see it, did I just miss it? Thanks for the video, been waiting for this one!
Hi I took apart the printer as shown in the video. When you mentioned that the display will come off it gave me some trouble and he ribbon cable going to it pulled out of the connection. When I put everything back in the printer does not power on. I believe it's that ribbon because it doesn't connect firmly. What's your take? and how do you take apart the display?
@@youarenotyourtraumapodcast I had to take the display off several times before I was able to get the ribbon back into its slot. It's difficult to see when I was attempting to install it back in. On mine, it's a black piece and the ribbon slides in. My only suggestion is to line it up with the display without the display hooked up so that you can get a good idea of how and where to push it in. That's the best advice I can offer.
I have the WF-7710. Have tried everything to unclog printhead. Any ideas? I took the printhead out. I cleaned the printhead. I used the solution.... NOTHING
Good day sir Kenvin can you help me to understand how paper feeder works on this model?thank you for the information on how to remove case and scanner. i be waiting for part two of your video. :)
Extremely useful, used the video to strip down my printer to get at a displaced paper guide. a couple of points: at 1:07 you say you can just disconnect the cable into the front panel. If you just pull it out it actually comes out of the socket at an angle which may damage the connector. The top edge of the front panel easily pops off and gives direct access to the connector so the cable can be removed without stress. You have to remove this edge piece anyway to reconnect that cable. Also at 2:54 you ease off the casing but you haven't mentioned removing the two deep screws at the front. It won't come off without those removed.
Excellent and helpful video, saved me buying a new printer!
Fantastic video and great job. You literally saved my WF-7200 from being trashed. I followed the video and dealt with the 000043 error. Thanks a ton!
Top tip; I had to reseat a pressure plate (5 off white plastic bits to right of cartridge run at 3:07 ) each plate holds a small black pressure roller and is spring loaded against the main paper transport roller. The small rollers are clipped into the plastic part but not very securely so, as you wrestle with the spring and the plate, it pops out and you have to start again.
I found that the roller could be tied into the plate with a thin wire or thread which can be cut and removed after all the parts are located. Makes life easier.
Fantastic. Not my model but the suggestion to go to your website was greatly appreciated. My 3-in-1 device WF-7250 had a broken hinge. aaaaaaai was able to find a replacement easily on AliExpress.
You are providing a great service with these videos Kevin, thank you.
Very welcome
epson has bad warranty support so i have to fix error 100016 or whatever which is a scanner error that grinds and this is helpful thank you . gotta fix my epscam now
you are the man Kevin where have you been for the last 6months ive lost so much till your video wow your amazing
Thanks, man! I’ve been MIA, but I’m back and ready to bring the good stuff. Let’s get this party started again!
This video helped me big time. Almost thoughti had to go buy a new printer
Do u have a video on how to install external waste tank ink on wf7710?
Hi Kevin thanks for this great video. My 7710 will not feed paper completely. It makes a load popping noise then feeds paper halfway. It will feed regular printer paper but no other type of paper. Also it says it's jammed but it's not. Can you point me in the right direction? Thanks again for the videos they a re a big help.
Hey Kevin can you tell me why my 7720 keeps giving me a out of paper on Cassette 1 error??? There's plenty of paper in it and epson couldn't figure it out, it's practically brand new I've had it for 3 years and I only used it literally a few times I never left ink cartridges inside when it's not in use.
Muy buen aporte! tenia que desarmar la WF-7710 ya que se me había cortado la correa del carro del cabezal... Gracias
Where does the ground cable to the lcd screen go? I can’t find where it needs to be attached to.
How do I put the lcd cable back in? I can't get it to turn on.
اتمنى كيفن ان تعطي لهذه الطابعه فيديوهات كثيرة ومشاكلها والاخطاء التى تحصل فيها
Hey Kevin. My Epson WF 7710 keeps popping error 034503 anytime I try printing or photocopying anything. Kindly assist with diagnosis.
Kevin, I went to BCH to purchase the workflow for the WF-7710 WF-7720 and did not see it, did I just miss it? Thanks for the video, been waiting for this one!
Almost done. I am marking all the wire colors, so you won't miss a wire. I will get it uploaded next week.
do you give coupons?
Hi I took apart the printer as shown in the video. When you mentioned that the display will come off it gave me some trouble and he ribbon cable going to it pulled out of the connection. When I put everything back in the printer does not power on. I believe it's that ribbon because it doesn't connect firmly. What's your take? and how do you take apart the display?
I have this same issue. I can’t figure out where this ribbon goes now my printer won’t turn back on.
@@youarenotyourtraumapodcast I had to take the display off several times before I was able to get the ribbon back into its slot. It's difficult to see when I was attempting to install it back in. On mine, it's a black piece and the ribbon slides in. My only suggestion is to line it up with the display without the display hooked up so that you can get a good idea of how and where to push it in. That's the best advice I can offer.
Kevin I can't seem to find where or how to reconnect the FCC cable to the LCD panel
Remove black trim. Has tabs holding it
I have the WF-7710. Have tried everything to unclog printhead. Any ideas? I took the printhead out. I cleaned the printhead. I used the solution.... NOTHING
Good day sir Kenvin can you help me to understand how paper feeder works on this model?thank you for the information on how to remove case and scanner. i be waiting for part two of your video. :)
Yes I can. Do you have a specific problem with the paper feed?
@@BCHTechnologies paper feeder not picking up paper on cassette 1 roller gear not working
I need to replace my lcd panel on my 7710. Where can I purchase it from
My lcd panel is just showing a white screen. How do I know if I just need to replace the tape or the whole control panel.
Hi Kevin. My printer wouldn’t turn back on after cleaning the print head. Any advice?
Did you find a solution? Mine has done the same i reckon a board is fried
你好，主播，我想要购买一个epson wf7621的打印头，不知道你这边有买么？
你好！是的，我们有卖Epson WF-7621的打印头。您也可以在eBay上找到。谢谢您关注和提问，如果您有更多问题或需要帮助，欢迎随时联系！
❤❤
Thanks for subscribing to my channel!