I appreciate the time you've put into the 5th-axis lesson, especially for free! I rarely come across informationally dense lessons. I r8 8/8 m8, it's gr8! New subscriber
Does any body knows why when i run the 5 axis post processor the A axis posted as incremental movements? fo sample if i rotate From A 0 TO a 45 came like A1,A2,A3,Etc Until reach 45 deg.
These came from Postability. You can get sim files from your post developer, like Postability who also tie the post into the sim, or you can make your own with files provided by your machine builder. Send Doosan an email asking for files and then follow the steps in this series of video to build the machine for simulation... ruclips.net/video/iDcaZ-6ZGco/видео.html ruclips.net/video/V-MlskbrH5I/видео.html
I did say NCI but I said it really fast so it sounded like a G 😃....good catch though, you are right. A Postability post and MachSim using that post, as good as gcode 👍 ....even though the video showed the other Simulation
I just emailed to your store about request some samples model that contains in 4th 5th axis book that I love to buy it. Because I couldn't see any inside the book what models are. Is this clip same in the book Sir? I love to learn this way not just demmo on some area 5th axis to be programmed. Is there any explanation about how to pick up work cordinate G54 for machine? Thank you Sir.
This lesson is part of the 5x course. These lessons do focus on programming Mastercam not so much setting up your machine. Focusing on machines is tough since there are so many different machines/controls to accommodate. There is some additional content coming for the Haas UMC machines in relation to setup and operation.
@@CamInstructor you said 5th axis course which is in the book called 4th, 5th axis? Or online courses? I am looking for a book. If machine with Funuc control so we have to use its post from machine manufacturer or Fanuc general? Thank you so so so much Sir
Depends on your budget. If money doesn't matter, Quadro RTX is what you're after (although new cards may be released this fall). Otherwise a good gaming card works just fine. RTX 2070/2060 or GTX 1660/1650 would be next steps below the Quadro and are good choices.
The table in the sim files is from the original umc750. The newer UMCs, not sure the year this started, have a smaller table. You can get the files from Haas and edit the machine or just modify the existing stl to match what you have.
Hi there! I just tested your files and they are great! But I can't generate the NC code. All the files I have put where you indicate. Is there any file missing? How can I generate NC code? Thanks
Ah, you're doing the 5X Free Lesson...missed that part. The download package does include a post but that post will not create gcode. It only populates text blocks within toolpaths. There should be mention of this in the lesson. Most 5X posts are locked and will need to be acquired directly from your reseller or on Mastercams website from the posts section.
Haas has their own controls, a Classic version and a Nextgen version. I think the symbol you’re seeing is the spindle direction, and yes, it really does look like Centroids logo!
"This machine does not leave a fine finish, rather it resembles the minimill that leaves tabletted or pixelated finishes." The machine is very good for the price point its at. You won't find much to compare to it in its price range. It is absolutely capable of fine finishes. This project does not try to push finishes, it pushes the use of 5x toolpaths on a part a student can make quickly.
The first 10 seconds in the video explained that the link to the lesson is 'down below'. This video is an overview of the lesson. You can click the mentioned link and it will take you to the lesson. The lesson consists of a Mastercam HLE download, machine simulation files, PDF document of the step by step instructions, videos of the steps, and exercise files to practice what you learned...all FREE. The only cost is your email address so you can log into the site.
The very beginning of the video mentions to click the link in the description that takes you to the *5 Axis Lesson* for the part shown. The lesson contains a download for Mastercam HLE, videos, documents, and machine simulation files for this part. The video is an overview of the lesson.....and yes, the linked lesson is *FREE* .
I appreciate the time you've put into the 5th-axis lesson, especially for free! I rarely come across informationally dense lessons. I r8 8/8 m8, it's gr8! New subscriber
Thanks for the feedback! It's always nice to hear!
Good job my friend. I like you video and my job is work in MasterCam
Thank you very much
the fact that you use a regular drill in the intro cracks me up
Glad you enjoyed it
Very useful video thanks for your time and effort and training👍
Glad it was helpful!
Thank you
You're welcome!
Awesome
Glad you liked it!
Do you have a video of how to create the surface for the top 3d tool path?
In the online course, yes.
Does any body knows why when i run the 5 axis post processor the A axis posted as incremental movements? fo sample if i rotate From A 0 TO a 45 came like A1,A2,A3,Etc Until reach 45 deg.
From where did you get the machine sim files. Haas or Mastercam? I could use for my Doosan VC630.
These came from Postability. You can get sim files from your post developer, like Postability who also tie the post into the sim, or you can make your own with files provided by your machine builder. Send Doosan an email asking for files and then follow the steps in this series of video to build the machine for simulation...
ruclips.net/video/iDcaZ-6ZGco/видео.html
ruclips.net/video/V-MlskbrH5I/видео.html
Mach Sim simulates the NCI code and not the G codes as mentioned @1:04. Good Video BTW
I did say NCI but I said it really fast so it sounded like a G 😃....good catch though, you are right.
A Postability post and MachSim using that post, as good as gcode 👍
....even though the video showed the other Simulation
I just emailed to your store about request some samples model that contains in 4th 5th axis book that I love to buy it. Because I couldn't see any inside the book what models are. Is this clip same in the book Sir? I love to learn this way not just demmo on some area 5th axis to be programmed. Is there any explanation about how to pick up work cordinate G54 for machine? Thank you Sir.
This lesson is part of the 5x course. These lessons do focus on programming Mastercam not so much setting up your machine. Focusing on machines is tough since there are so many different machines/controls to accommodate. There is some additional content coming for the Haas UMC machines in relation to setup and operation.
@@CamInstructor you said 5th axis course which is in the book called 4th, 5th axis? Or online courses? I am looking for a book. If machine with Funuc control so we have to use its post from machine manufacturer or Fanuc general? Thank you so so so much Sir
what graphics card do you use for simulation? I need to do some graphics upgrades on my desktop but am unsure what to get...
Depends on your budget.
If money doesn't matter, Quadro RTX is what you're after (although new cards may be released this fall). Otherwise a good gaming card works just fine. RTX 2070/2060 or GTX 1660/1650 would be next steps below the Quadro and are good choices.
Could you recommend me what book to buy for 5axis on stimulator because my shop plan to get big stimulator machine. Thks
We have a 5 Axis course on our website you should look at.
In machine installation part your umc 750 table seems bigger than actual machine. I tried sinulation with one of my part today then i noticed that.
The table in the sim files is from the original umc750. The newer UMCs, not sure the year this started, have a smaller table. You can get the files from Haas and edit the machine or just modify the existing stl to match what you have.
@@CamInstructor Do you have any video about how to modify existing stl?
Hi there! I just tested your files and they are great! But I can't generate the NC code. All the files I have put where you indicate. Is there any file missing? How can I generate NC code? Thanks
If you are using HLE you cannot post gcode.
@@CamInstructor Hi there! thanks, but i don't use HLE, i use an industrial version
Ah, you're doing the 5X Free Lesson...missed that part. The download package does include a post but that post will not create gcode. It only populates text blocks within toolpaths. There should be mention of this in the lesson. Most 5X posts are locked and will need to be acquired directly from your reseller or on Mastercams website from the posts section.
Hi Sir. How can I get free download 5th axis vise to merge into mastercam like your video showing? Thks a lot
We include it in some of the lessons but you can also get it from their website.
fifthaxis.com/
sir i want to learn master cam sir please tell me basic command
Does this Haas use a Centroid Control? It looks like their logo on the screen at 2:40
Haas has their own controls, a Classic version and a Nextgen version. I think the symbol you’re seeing is the spindle direction, and yes, it really does look like Centroids logo!
I waiting ur 5 axis but tech a to in that don't hide anything.. plzz
Nothing is hidden! Click the link and it takes your to the course. Have fun!
how much is haas paying you to mention their name ?
I sent them an invoice for a million $$ plus a couple free machines....they haven't replied :)
Can you share .mcam file here???
Please use this link and sign up to receive the free lesson: info.caminstructor.com/mastercam-5axis-lesson8
esta maquina no deja un acabado fino ,, mas bien se parece a la minimill que deja acabados tableteados o pixeleados .. la verdad muy malos servos
"This machine does not leave a fine finish, rather it resembles the minimill that leaves tabletted or pixelated finishes."
The machine is very good for the price point its at. You won't find much to compare to it in its price range. It is absolutely capable of fine finishes. This project does not try to push finishes, it pushes the use of 5x toolpaths on a part a student can make quickly.
What was the lesson? This was nothing more than a demo, packaged as a "lesson"...
The first 10 seconds in the video explained that the link to the lesson is 'down below'. This video is an overview of the lesson.
You can click the mentioned link and it will take you to the lesson. The lesson consists of a Mastercam HLE download, machine simulation files, PDF document of the step by step instructions, videos of the steps, and exercise files to practice what you learned...all FREE. The only cost is your email address so you can log into the site.
What is this a lesson for? You showed people how to do nothing.
The very beginning of the video mentions to click the link in the description that takes you to the *5 Axis Lesson* for the part shown. The lesson contains a download for Mastercam HLE, videos, documents, and machine simulation files for this part. The video is an overview of the lesson.....and yes, the linked lesson is *FREE* .