Dear Mohammed, your video is very helpful. I am new in this area. Can you please recommend a book where I can get step by step guide for machining using abaqus?
Shamsul Arefin Hi You do not need book to learn machining in abaqus. Just watch the videos metal cutting and indentation in RUclips Manny times. Then writ notes For example Step Create parts Step 2 define material Step 3 define section Step4 assembley Step5..... ...... Step n submit Each step explain in detials in your way to understand. I used this way and work it with me. Good luck
Hello, Thanks a lot for the simulation. It was very informative. Could you please tell how long your simulation ran for? I have exactly folllowed the steps you have said in this tutorial and it has been running for more than 1 day (25 hours and still running). Is it normal because of the explicit analysis type ? Your comments would be appreciated. Thanks in Advance.
Your video is very helpful! Can you explain me how to make an orthogonal cutting in ABAQUS/Implicit (to simulate quasi-siatic conditions, without inertial effects)? I've been having convergence problems... Your help would be highly appreciated!
Hi ! is an excelent video tutorial, I have a question... could you tell me how to obtain the parameters of the material to use the johnson-cook material model and damage criteria??? thanx!
Experimentally. Although, the parameters for general materials have been already published on the internet which were calculated by some earlier experiments .
Sir I am unable to do this simulation in student version... I am struct at the tool movment .. Solving got over but tool is not moving .. Please help me in this regards.. Thank you
hi would you please say according to which article (data) you have done the simulation? i need them for the comparison between simulated and experimental data.
Hello Mohammed, Can you help me with something? I'm simulating something like this but I need the forces and when i try to open the ODB file, there are just the energy plots. Another question how could you assign a Sheel with the Solid Homogenous section, I'm trying but the option is not available.
Dear@Mohammed Saber sir i am not getting temperature variation though stress values are coming. temperature is coming to be same at all the nodes. i have mailed the CAE file. please look into it and reply.
Hello, if possible can you tell how to generate nodes, once I am selecting surface it gives error, as you also told in your video, if possible please explain how to make nodes, as I am doing reverse analysis i.e impact test in 2D planar.
Hello. I am working on this similar work. But facing some problems like: when I perform it in Dynamic Explicit, the chip forms. But for Dynamic, temperature Displacement, Explicit I did not found any option for element deletion. Another problem is the stress distribution shows only in chips and W/P surface not in the cutting tool. How can I overcome these? Thanks.
I work to simulation of composite material cutting by Abaqus with cohesive zone element ,when i make submit i have excessive distortion could you help me ,Hello Mr. Mohammed Saber
hi mohammad saber... i have project on prediction on cutting tool using FEA (in my case using Autodesk simulation) can i just do the same you do on ABAQUS in Autodesk simulation?? can you help me?
Hi, I want to run the same case for Dynamic, Temp-disp, Explicit, But the element deletion option is not available for that one. Please help me for the same.
Hello, Do you know endmilling simulation? Or u have any other tutorial for endmilling process simulation? Please mail me @ gowthamv19@gmail.com. Thanks
Hello sir, How to provide rotational velocity of tool in case of facing operation during simulation? and tool feed rate? is tool feed rate and velocity in boundary condition same?
hiiii...can you suggest me that.....why the value of force is too high(in the range of E6).....in my case same same result is coming....please give some idea....
Set the thickness of Plane Strain section to you actual workpiece thickness then you will have reasonable values. In my analysis, it was 1 , the default in Abaqus, which means the thickness is 1 m which is too high.
Hi guys I am getting this error when executing the abaqus file...can anyone suggest the reason The executable C:\Temp\6.8-2\exec\explicit.exe aborted with system error code 144. Please check the .dat, .msg, and .sta files for error messages if the files exist. If there are no error messages and you cannot resolve the problem, please run the command "abaqus job=support information=support" to report and save your system information. Use the same command to run Abaqus that you used when the problem occurred. Please contact your local Abaqus support office and send them the input file, the file support.log which you just created, the executable name, and the error code.
mon preojet : l effet de la regosité sur le comportement tribologique (contact sphere/plan) donc j arrive pas introduire les parametres de la regosité sur abaqus / comment ? mrc
My project: the effect of roughness on the tribological behavior (contact sphere / plan) so I can not introduce the parameters of the regosity on abaqus / how? think's
I did 2d and 3d and i defined the same material properties and also i defined for tool and i did the simulation in explicit as you did exactly and i checked the deletion and contact definition and ALE and everything but every time in 2d and 3d abaqus doesnt cut the material and the material sticks to the tool ! Do you know what is the problem? Im confused !
I check marked the output STATUS "some failure and plasticity models AVUMAT" and now in 3d it shows normal cutting but still material doesnt fail in 2d! i wonder which result output i should check
Hello Mohammed Saber Thank you for this video I followed the video step by step it gave me almost the same result, but the damaged elements are not deleted! where you think is the problem? I selected yes for element deletion! the job was aborted with this error (The elements in element set ErrElemZeroALEMass-Step1 have zero or negative mass.) Can you please send me the cae file
HI , thanks for this nice video .please I do this example but there error in the result can I send you the file to look it what is the error thank you for help
Mohammed Saber Hi thanks for the response. Could you please tell me how could i use (Cockcroft Latham) model? im new in abaqus and i dont know where and how i could write the equation
Do you know how could i find the equations used in ABAQUS for defining these parameters? for example in"shear damage" section, abaqus wants me some parameters like strain , etc but i dont know what equation it means for "shear damage" ?
please can you help me!i have coupled thermal-mechanical (heat generation, thermel conductance...) analysis of metal cutting simulation!the simulation doesn't work with me ! can i send u CAE fileto chek it! thank you
Can you help me, please i do metal cutting simmulation about thermal analysis with abaqus. Can i get the cae files so i can learn something akbar.reza.pratama@gmail.com
Hi Guys I am working on ABAQUS and have got some good results but now facing some problems that I want to discuss with you 1. I have imported a newly designed tool from the CATIA in .stp format but it is not rotating and only shows translatory motion. this problem I have seen earlier also and my conclusion is that there must be some problem in designing of tool in CATIA. what is your view on this????? can it be the reason or there is some other reason behind that???? As the tool which was succesfully working was also designed in CATIA 2. How to calculate tool wear in ABAQUS??? 3. How to get the cutting forces in x,y,z directions????? I will be highly thankful to you if you can help me in solving these problem????
Farooq Ahmed 1. I don't know about this. 2. There will be no tool wear if you define tool as a rigid body. 3. Forces can be measured as shown in this video.
Sir, Thank you, very good illustration.
جزاكم الله خيرا يا دكتورنا الفاضل
حضرتك تعرف الدكتور محمد صابر
لو حضرتك تعرفه ممكن تقولى اوصله إزاى لو سمحت
Very useful for me. Thanks a lot.
Beautiful work!
Dear Mohammed, your video is very helpful. I am new in this area. Can you please recommend a book where I can get step by step guide for machining using abaqus?
Shamsul Arefin
Hi
You do not need book to learn machining in abaqus. Just watch the videos metal cutting and indentation in RUclips Manny times.
Then writ notes
For example
Step Create parts
Step 2 define material
Step 3 define section
Step4 assembley
Step5.....
......
Step n submit
Each step explain in detials in your way to understand.
I used this way and work it with me.
Good luck
Hello, Thanks a lot for the simulation. It was very informative. Could you please tell how long your simulation ran for? I have exactly folllowed the steps you have said in this tutorial and it has been running for more than 1 day (25 hours and still running). Is it normal because of the explicit analysis type ? Your comments would be appreciated. Thanks in Advance.
Thanks a lot for your kindly tutorial
very nice video thank you very much
great job sir
The tool isn't moving on giving Velocity in BCs. It moves with giving displacement. Why so?
Hi,
I appreciate the simulation.
But it so confusing because of back and forth, i am not getting the flow
Your video is very helpful! Can you explain me how to make an orthogonal cutting in ABAQUS/Implicit (to simulate quasi-siatic conditions, without inertial effects)? I've been having convergence problems... Your help would be highly appreciated!
Thank you very much！
Hi ! is an excelent video tutorial, I have a question... could you tell me how to obtain the parameters of the material to use the johnson-cook material model and damage criteria??? thanx!
Experimentally. Although, the parameters for general materials have been already published on the internet which were calculated by some earlier experiments .
Thank you so much sir...
Good Work...
Superb
+Yoann GIESI Thanks
Sir I am unable to do this simulation in student version... I am struct at the tool movment .. Solving got over but tool is not moving .. Please help me in this regards.. Thank you
thank you
Hi, the video is very informative. What would like to know what parameters control the formation of Chip
hi would you please say according to which article (data) you have done the simulation? i need them for the comparison between simulated and experimental data.
Hello Mohammed, Can you help me with something? I'm simulating something like this but I need the forces and when i try to open the ODB file, there are just the energy plots. Another question how could you assign a Sheel with the Solid Homogenous section, I'm trying but the option is not available.
thank u for video
Dear@Mohammed Saber sir i am not getting temperature variation though stress values are coming. temperature is coming to be same at all the nodes. i have mailed the CAE file. please look into it and reply.
In Which literature can I find the values of JC parameters used in this Video ? If someone knows please Tell me !
very nice video thank you very much mister mssaberplease can you give me some advice in modelling friction stir welding because I need it regard
Hello, if possible can you tell how to generate nodes, once I am selecting surface it gives error, as you also told in your video, if possible please explain how to make nodes, as I am doing reverse analysis i.e impact test in 2D planar.
very useful keep going ;)
+Adnane Chakour Thanks
hello
How can we display the temperature for this type of simulation
(Abaqus CAE explicit coupled thermo-mechanical)
Hi! Could you post a tutorial about how to make a turning operation on abaqus?
Thanks!
Hello. I am working on this similar work. But facing some problems like: when I perform it in Dynamic Explicit, the chip forms. But for Dynamic, temperature Displacement, Explicit I did not found any option for element deletion. Another problem is the stress distribution shows only in chips and W/P surface not in the cutting tool. How can I overcome these? Thanks.
Hi I wish you are doing well , I am working in a similar project I hope you can give me some helpful references,videos ...
I work to simulation of composite material cutting by Abaqus with cohesive zone element ,when i make submit i have excessive distortion could you help me ,Hello Mr. Mohammed Saber
hi mohammad saber... i have project on prediction on cutting tool using FEA (in my case using Autodesk simulation) can i just do the same you do on ABAQUS in Autodesk simulation?? can you help me?
Well done, tnx
file is showing this error (Zero or negative mass in element number PART-1-1.1753) please give me reply asap
Hi, I want to run the same case for Dynamic, Temp-disp, Explicit, But the element deletion option is not available for that one. Please help me for the same.
Send me you. cae to check. I think it is a matter of field output.
hello can we find out temperature generated during orthogonal turning in 2D?
This video is more interesting
Hello, i have done as your direction, but my reaction force equals to zero. Could u please tell me how to solve this problem? Thanks
Hello, Do you know endmilling simulation? Or u have any other tutorial for endmilling process simulation? Please mail me @ gowthamv19@gmail.com. Thanks
Hello, can you make a tutorial in MARC on this same experiment
Hi
,How i can appoint R.point ?Thank you very much for this simulation
Could you please tell me if possible simulation of cutting fluid during process by this ABAQUS software
Sir what type of alluminum you have used????
sir, can please tell me which force is cutting force and which force is thrust force in the history output we are getting?
RF 1 is the cutting force and RF 2 is the thrust force.
ممكن اكلم حضرتك فى شغل مع حضرتك دكتوره من جامعة بنها.
يرجى الرد سريعا للضرورة
Hello sir,
How to provide rotational velocity of tool in case of facing operation during simulation?
and tool feed rate? is tool feed rate and velocity in boundary condition same?
Rotational velocity of *workpiece (instead of tool)
ruclips.net/video/z2Qk2t-_bCE/видео.html
i can't cut subject ; tool are running but it's not cutting ,could you help me fix ?
ruclips.net/video/z2Qk2t-_bCE/видео.html
hiiii...can you suggest me that.....why the value of force is too high(in the range of E6).....in my case same same result is coming....please give some idea....
Set the thickness of Plane Strain section to you actual workpiece thickness then you will have reasonable values. In my analysis, it was 1 , the default in Abaqus, which means the thickness is 1 m which is too high.
Mohammed Saber
can i modify that thickness value?
where to set the thickness in abaqus
Hi guys I am getting this error when executing the abaqus file...can anyone suggest the reason
The executable C:\Temp\6.8-2\exec\explicit.exe aborted with system error code 144. Please check the .dat, .msg, and .sta files for error messages if the files exist. If there are no error messages and you cannot resolve the problem, please run the command "abaqus job=support information=support" to report and save your system information. Use the same command to run Abaqus that you used when the problem occurred. Please contact your local Abaqus support office and send them the input file, the file support.log which you just created, the executable name, and the error code.
Do you use subroutines?
Hello, could it possible to share the abaqus input file for the same study explained above ?
Try this channel:" Steffen B." on RUclips . Found a lot of Abaqus and Ansys Fem Tutorials.
mon preojet : l effet de la regosité sur le comportement tribologique (contact sphere/plan) donc j arrive pas introduire les parametres de la regosité sur abaqus / comment ? mrc
In English, please.
My project: the effect of roughness on the tribological behavior (contact sphere / plan) so I can not introduce the parameters of the regosity on abaqus / how? think's
Sorry, I have not done this before.
ok mohamed think u very much for your time . but if you can oriented me , or give me any website can help me in my project . think you again ,
I did 2d and 3d and i defined the same material properties and also i defined for tool and i did the simulation in explicit as you did exactly and i checked the deletion and contact definition and ALE and everything but every time in 2d and 3d abaqus doesnt cut the material and the material sticks to the tool ! Do you know what is the problem? Im confused !
send me your file to check.
mssaber77@yahoo.com
I check marked the output STATUS "some failure and plasticity models AVUMAT" and now in 3d it shows normal cutting but still material doesnt fail in 2d! i wonder which result output i should check
i can help, mail to prakashkmuthu@gmail.com
Hello Mohammed Saber
Thank you for this video
I followed the video step by step it gave me almost the same result, but the damaged elements are not deleted! where you think is the problem? I selected yes for element deletion! the job was aborted with this error (The elements in element set ErrElemZeroALEMass-Step1 have zero or negative mass.)
Can you please send me the cae file
hello contact me my mail is khalfallah.chou3aib@gmail.com
same
HI , thanks for this nice video .please I do this example but there error in the result can I send you the file to look it what is the error thank you for help
+mssaber77 Thank you very much for your response kind regard
+mssaber77 it is really wonderful and helpful file .it is relating to drilling .please are you have the one for cutting kind regard
Anyone can help me to do simulations Subsurface damage of Tungsten? Thank you
is it possible to define another damage model while i use Johnson-C plastic model in abaqus???
Yes
Mohammed Saber Hi thanks for the response. Could you please tell me how could i use (Cockcroft Latham) model? im new in abaqus and i dont know where and how i could write the equation
I have not used the Cockcroft Latham model before and I think it is not available in ABAQUC/CAE. Therefore, you may need to a subroutine.
Mohammed Saber tnx
Do you know how could i find the equations used in ABAQUS for defining these parameters? for example in"shear damage" section, abaqus wants me some parameters like strain , etc but i dont know what equation it means for "shear damage" ?
could you plz tell me how u set the Ada-1 in ALE? just default or something else?
If I remember well, it was the default setting.
yeah.though i still don't konw how to set ALE correctly, but i've made out the similiar figure in Abaqus, due to ur help. THANKS a lot
what material the work piece ?
please can you help me!i have coupled thermal-mechanical (heat generation, thermel conductance...) analysis of metal cutting simulation!the simulation doesn't work with me ! can i send u CAE fileto chek it! thank you
Ok, send my your file and I will check them for you.I am using Abaqus .CAE . 6.10 and 6.14 my e-mail is given in the description of my channel.
ok!i have sent you a cae file! and i explained everything in your mail :D
Can you help me, please
i do metal cutting simmulation about thermal analysis with abaqus. Can i get the cae files so i can learn something
akbar.reza.pratama@gmail.com
Mohammed Saber can you help me with abaqus ? I do the same like jihene boukédi. Please help me.
ruclips.net/video/z2Qk2t-_bCE/видео.html
u r video is so helpful that i've subscribe u . longing for more help T T
请问你也是做切削仿真的吗？我刚进这个领域，咱们能交流交流不? ；）
Hello, Is it possible in Ansys ?
I have mailed you a query .kindly Please help me to find it out.
الملف لا يعمل على النسخة 13 يا اخي محمد
It was created using 6.14.
Hi Guys
I am working on ABAQUS and have got some good results but now facing some problems that I want to discuss with you
1. I have imported a newly designed tool from the CATIA in .stp format but it is not rotating and only shows translatory motion. this problem I have seen earlier also and my conclusion is that there must be some problem in designing of tool in CATIA. what is your view on this????? can it be the reason or there is some other reason behind that???? As the tool which was succesfully working was also designed in CATIA
2. How to calculate tool wear in ABAQUS???
3. How to get the cutting forces in x,y,z directions?????
I will be highly thankful to you if you can help me in solving these problem????
Farooq Ahmed 1. I don't know about this. 2. There will be no tool wear if you define tool as a rigid body. 3. Forces can be measured as shown in this video.
لدي سوال لو ممكن
GO on!!!!
مصر