Thanks very much for this video. The 2012, J10 Qashqai I was working on with the K9K 1.5 DCI engine had pretty much the same fault. It gave fault codes, C1132 and a couple of steering angle sensor codes, C1143 & C1144 I removed this pressure pipe and it was a little coked up but not blocked. It turned out to be the exhaust air pressure sensor that this pipe connects to. It looked like it had seen better days and because the pipe wasn't blocked. I pin pointed the sensor. Replaced it.. cleared codes and all is well. What a crazy fault to signal such a code. This video definitely pointed me in the right direction. Thank you
Just found this the other week. Had a "nosey" around the engine bay to check where it was last weekend. Bought a steel bike cable (£1.50: an idea I found on another blog post). Took the pipe off yesterday (bolt first then the tube). Spent about 30..60 mins patiently using a drill with a section of the bike cable to drill/clean the pipe. Once fully unblocked, put it back in the car. No further issues re: lights on the dashboard. I'd just like to say: "*Fabulous* youtube video Sandy. I have had this problem for some time - and yours was the first that really explained the problem and (more importantly) what the solution is - thank you so much!"
@@winstonlee5382 ... there is a spring clip at the top of the rubber tube. I simply squeezed it a little as I pushed the tube down away from the sensor. It’s a little difficult to get to... but doable. It should slide off as you push down and rotate back and forth a little.
We managed to unblock it with a welding rod and brake cleaner, don't think ours was quite as bad. Although almost thought it wasn't fitted on our car, it's well hidden. Thanks mate
Just got these lights on mine today. I'll start here. Thanks alot mate!! Why does it have to be hard to get too 😥 every job I do you need hands like a mouse.
Thank you, man! I had the same problem, after finding the error code, I showed to the the mechanic your video and it really helped him. That fuckin' pipe was really filthy and , of course, clogged. Now it works fine. Greetings from Romania!
Thanks Bill good to hear from u, how's the weather in California? wishing we were back there but this year we are going to Israel, hope your well cheers sandy
can you show where is this exactly located I think i have similar model? its 2011 Qashqai+2? Do i need to open up that pipe to get access to it or have to remove battery etc? thanks
I've just had this code pop up on my qashqai, could I not use a carb / egr valve cleaner with a piece of wire? I'm not paying for a new one when I can just as easily start to learn to maintain my car the hard way lol
Brilliant video! Thanks for sharing. Same problem, same fix. Struggled to find/ remove pipe, but got there in the end! Would never have found/ fixed this without your help! Cheers 🍻 🔧👍
Well I managed to do it and it was a pain especially trying to get it connected back up but like everything if you persevere you get there in the end. I found that the pipe WAS blocked but after clearing it I still have the anti skid lights still on... do the lights normally go out on thier own or do they need to be reset if not I need to look else where
I just had this pipe (the new pipe is slightly modified by Nissan these days) replaced but the lights were still turning on regularly. It turned out to be the MAP sensor. This was not expensive and anyone can replace in 5 minutes. No reset was necessary.
@@sandyande could i ask pleaae if u had c1131 and 31132 and u replaced switch for pressure sensor and new pipe y it still throws up light randomly do u know wat state 2 means please n thanku
my Juke has the same error, but since the error appeared, fuel consumption has increased to as much as 11L/100km, could it be due to this? (i have juke F15, 1.5 DCI diesel)
Hi Sandy - thanks for a very video - can the red pipe be pulled off the sensor or is it held On by a clip - i have found the sensor and as you say its very hard to get too and i am finding it hard to remove the rubber res pipe - how did you do it? Thanks again
I have same P1525 problem on my infiniti , lot of money, 3 different mechaninics and still have same problem.....car cannot accelerate a lot otherwise ECU cuts the engine and give me this code but it is not same engine and I cannot find that pipe
I've got the same issue... just had a look and located the pipe, it's a bugger to get at. Did the red pipe just pull off with the clip still attached or did you have to cut it....
Could it be easier to get at it from underneath? I have the same problem after turbo swap and egr clean, had i known i would have done it when turbo and egr was out.
@@sandyande So today i manned up to give it another go. I removed the battery and the tubes/pipes to the turbo, but alas, no sensor to be found. So i checked for the j11 sensor on the left side, but nothing there either. I must have a different config. it is a 1.5 DCI 2007.
I had this problem after changing the pressure pad. Car traction is low. it just turns on these lights on the intercity road. Is it possible that it is due to the pressure pad? thanks
@@sandyande I had this problem after changing the pressure pad. Car traction is low. it just turns on these lights on the intercity road. Is it possible that it is due to the pressure pad? thanks
@@JamesClough-uz6pi unfortunately no. The source of this code was faulty abs sensor. However sometimes the code reappears along side with the exhaust pressure sensor fault. However it is able to get erased with my diagnostic tool.
I'm having the same problem with my QASHQAI right now. Mine is 2014 model with 1.2 engine and benzin. It's been to mechanic 6 times, but they can't fix it. Can this technic also work on QASHQAI 2014 benzin model? I need help???
Hi Peter, i have the same issue 1.2 Benzin engine. Did you find the issue? Can you please advise me what's the reason? My car runs weak not much power. Thank you
@@MOMO-yf5os after several visits to different workshops. They discovered that it was engine failure. I had quarantee on the car. So, I returned it back to the dealer and changed it to another car. I dont have it again. Its out of hands...
You may clean it, you don't have to replace it, it's pretty expensive for a short pipe of copper !It cleans up pretty easy, three days ago I solved the problem. I've drove 6 months with ESP light on, now I can't believe when I look in the board :) It costs over 120 euro (500 lei + in Romania) pipe and it's brought on the order from Nissan, from my point of view it's not worth it. If it's any help, my mechanic said this pipe came from a motor valve, right in the ABS, that's how much I got:) Eu nu as banii pe una noua!
It's a joke after putting a new turbo into my 141 Nissan qashqai and then it was saying under boast so new sensors and pump fitted now I have the C1130 code up the garage who fitted parts told me pip was all cleaned ect and the car has full service history and only 70,000 miles on it 🙈🙈🙈 and just so you know I have 1,600 euros spent so far
Thanks very much for this video.
The 2012, J10 Qashqai I was working on with the K9K 1.5 DCI engine had pretty much the same fault. It gave fault codes, C1132 and a couple of steering angle sensor codes, C1143 & C1144
I removed this pressure pipe and it was a little coked up but not blocked. It turned out to be the exhaust air pressure sensor that this pipe connects to. It looked like it had seen better days and because the pipe wasn't blocked. I pin pointed the sensor. Replaced it.. cleared codes and all is well.
What a crazy fault to signal such a code. This video definitely pointed me in the right direction.
Thank you
Happy to help cheers sandy
Podéis mandar una foto de donde está la tubería, no logro encontrarla
Just found this the other week. Had a "nosey" around the engine bay to check where it was last weekend. Bought a steel bike cable (£1.50: an idea I found on another blog post). Took the pipe off yesterday (bolt first then the tube). Spent about 30..60 mins patiently using a drill with a section of the bike cable to drill/clean the pipe. Once fully unblocked, put it back in the car. No further issues re: lights on the dashboard. I'd just like to say: "*Fabulous* youtube video Sandy. I have had this problem for some time - and yours was the first that really explained the problem and (more importantly) what the solution is - thank you so much!"
Cheers Glad to help, Sandy
How did you manage to get it off from the top? I can seem to get it off from the top, after removing the bolt.
@@winstonlee5382 ... there is a spring clip at the top of the rubber tube. I simply squeezed it a little as I pushed the tube down away from the sensor. It’s a little difficult to get to... but doable. It should slide off as you push down and rotate back and forth a little.
@@carolallen3900 did you remove battery and air box to get to the 13m bolt ?
@@muhammadarfan4663 nope.touch and feel only
Thank you :) I have the same problem on 1.5dci 81kw. This video solve my problem.
We just had the same thing at work, this video was a massive help. Thanks Sandy
Great Matt did u use Rodys method of burning it out cheers sandy
We managed to unblock it with a welding rod and brake cleaner, don't think ours was quite as bad. Although almost thought it wasn't fitted on our car, it's well hidden.
Thanks mate
I just wanted to say thanks for this video it fixed my problem also very much appreciated
Many tanks Sandy, i had the same problem, very helpfull!
Tanks again. Daniele
Happy to help cheers sandy
Thank you Very helpful for me 👍🏾
Супер !!! Спасибо, машина 2011 год та же проблема и именно так исправил )))
а тяжело было снять???
в какую сторону откручивать?
@@user-ze3wl1ei9r снимал мастер когда менял грм.. вроде особой сложности не было
@@user-ze3wl1ei9r парни, как снимали?
Just got these lights on mine today. I'll start here. Thanks alot mate!! Why does it have to be hard to get too 😥 every job I do you need hands like a mouse.
because it's a Renault. Renault designers are the biggest fannies on the planet.
Nice one chaps appreciate the video 👍🏼
Done the banjo bolt, how do u get the pipe off just pull? Or do you have to try and get the clip off?
Same problem today at work as well. Video helped a lot. Thank you mate!
Have one in today sandy thanks for sharing
Done one of these recently! Great curve ball 😆
I know what were the Japanese engineers thinking about when the hard codes in the abs!!! Cheers sandy
I will check this tomorrow thanks !
Thank you, man! I had the same problem, after finding the error code, I showed to the the mechanic your video and it really helped him. That fuckin' pipe was really filthy and , of course, clogged. Now it works fine. Greetings from Romania!
Greetings from Scotland Ciprian cheers sandy
How was the pipe cleaned ?
@@muhammadarfan4663 In my case, with an air compressor for tires.
Worked for my Qashqai, thanks very much.
Hi, any idea on the exact size of the banjo bolt. Have dropped.mine!
I've heard of this problem but not come across one yet. Handy to know 👍
No problem happy to share, take care, Sandy
Great job Sandy!!
Thanks Bill good to hear from u, how's the weather in California? wishing we were back there but this year we are going to Israel, hope your well cheers sandy
Very hot here. Wish I was there.
can you show where is this exactly located I think i have similar model? its 2011 Qashqai+2? Do i need to open up that pipe to get access to it or have to remove battery etc? thanks
I've just had this code pop up on my qashqai, could I not use a carb / egr valve cleaner with a piece of wire? I'm not paying for a new one when I can just as easily start to learn to maintain my car the hard way lol
Brilliant video! Thanks for sharing. Same problem, same fix. Struggled to find/ remove pipe, but got there in the end!
Would never have found/ fixed this without your help!
Cheers 🍻 🔧👍
Glad to help Andrew, Sandy
Had same issue on my NV200 1.5 dci, long time needed to remove the pipe, but issue fixed (2 years ago)
cannot see where thr pipe is ,any suggestions?
Hi I'm guessing if you pull sensor out of pipe and start engine..you should have exhaust gas coming out ..looks a pig to get too
I have a Qashqai model 2011 .... which is this tube ..... I can not find it
You need a diamond eye threader. To get thru. Then tiny piece of rag attached to threader in the way back
Well I managed to do it and it was a pain especially trying to get it connected back up but like everything if you persevere you get there in the end.
I found that the pipe WAS blocked but after clearing it I still have the anti skid lights still on... do the lights normally go out on thier own or do they need to be reset if not I need to look else where
I reset that one but u would think they would reset automatically after 3 starts if fault is gone!
I just had this pipe (the new pipe is slightly modified by Nissan these days) replaced but the lights were still turning on regularly. It turned out to be the MAP sensor. This was not expensive and anyone can replace in 5 minutes. No reset was necessary.
love ur videos m8 great work can i ask question to help a diy eedjit would this put car into limp mode and not rev??? thanks for any info
Yes definitely 👍
@@sandyande could i ask pleaae if u had c1131 and 31132 and u replaced switch for pressure sensor and new pipe y it still throws up light randomly do u know wat state 2 means please n thanku
my Juke has the same error, but since the error appeared, fuel consumption has increased to as much as 11L/100km, could it be due to this?
(i have juke F15, 1.5 DCI diesel)
Hi Sandy - thanks for a very video - can the red pipe be pulled off the sensor or is it held
On by a clip - i have found the sensor and as you say its very hard to get too and i am finding it hard to remove the rubber res pipe - how did you do it? Thanks again
I think we just pulled it to release cheers sandy
Thanks
Great vid. I have a similar problem with both lights on but my code reader only shows up p codes. What scan tool do you use?
The video shows the snap on Verus but I also use autel and launch cheers sandy
@@sandyande thanks for that mate 😀👍
Worked for me on a 2011, nightmare job but light has now cleared!!!! Didn’t need to reset the light, disappeared on its own!!
Name of the part pls, I have same problem with my Nissan qashqai 1.5 Dci 2011
I use mig welding wire. Works a dream.
I have same P1525 problem on my infiniti , lot of money, 3 different mechaninics and still have same problem.....car cannot accelerate a lot otherwise ECU cuts the engine and give me this code but it is not same engine and I cannot find that pipe
I've got the same issue... just had a look and located the pipe, it's a bugger to get at.
Did the red pipe just pull off with the clip still attached or did you have to cut it....
Yes just pull it off!
Need a bigger pipe
Could it be easier to get at it from underneath? I have the same problem after turbo swap and egr clean, had i known i would have done it when turbo and egr was out.
Hi not sure u can get access from below cheers sandy
@@sandyande So today i manned up to give it another go. I removed the battery and the tubes/pipes to the turbo, but alas, no sensor to be found. So i checked for the j11 sensor on the left side, but nothing there either. I must have a different config. it is a 1.5 DCI 2007.
I had this problem after changing the pressure pad. Car traction is low. it just turns on these lights on the intercity road. Is it possible that it is due to the pressure pad? thanks
@@sandyande I had this problem after changing the pressure pad. Car traction is low. it just turns on these lights on the intercity road. Is it possible that it is due to the pressure pad? thanks
Do you need to go under the car to remove this pipe? And thanks for the video!
No, all completed from the top but quite awkward to get at cheers sandy
I've been quoted nearly £300 for the job of replacing this pipe. Parts and labour. Is that reasonable?
Try and do the job yourself or get help to do it and u will save yourself at least £270💰
I have the 1.6 dci. Yesterday the car comunicated the same error codes. Are the pipe on the same side as in the video?
How have you got on? I have the same issue. Im gonna try and remove the pipe tomorrow. Wish there was a guide for where the pipe is
@@JamesClough-uz6pi unfortunately no. The source of this code was faulty abs sensor. However sometimes the code reappears along side with the exhaust pressure sensor fault. However it is able to get erased with my diagnostic tool.
@@JamesClough-uz6pi did you manage to take it out and clean? I wonder how difficult it might be.
Thanks mate its happened to my car I have done the same the pipe was blocked the easy way to clean Is burning with fire gun
I'm having the same problem with my QASHQAI right now. Mine is 2014 model with 1.2 engine and benzin. It's been to mechanic 6 times, but they can't fix it. Can this technic also work on QASHQAI 2014 benzin model? I need help???
Sorry no idea
Hi Peter, i have the same issue 1.2 Benzin engine. Did you find the issue? Can you please advise me what's the reason? My car runs weak not much power. Thank you
@@MOMO-yf5os after several visits to different workshops. They discovered that it was engine failure. I had quarantee on the car. So, I returned it back to the dealer and changed it to another car. I dont have it again. Its out of hands...
Sandy, do you happen to know if Qashqai's from 2007 Tekna model had this pipe on their engine?
Sorry no idea
Where is this on a 2.0 dci? Qashqai?
2.0dci is completely different engine to french 1.5dci
Bonjour vous procédez comment pour le démonter le tuyau car j ai le même problème depuis deux semaines merci beaucoup cordialement
Bonjour si tu as la solution je veux bien même problème
Hello. I have the same problem and I want to order one
.
What is the name of the pipe? code pls.. THX
Sorry no idea of name or part no. Cheers sandy
You may clean it, you don't have to replace it, it's pretty expensive for a short pipe of copper !It cleans up pretty easy, three days ago I solved the problem. I've drove 6 months with ESP light on, now I can't believe when I look in the board :) It costs over 120 euro (500 lei + in Romania) pipe and it's brought on the order from Nissan, from my point of view it's not worth it. If it's any help, my mechanic said this pipe came from a motor valve, right in the ABS, that's how much I got:)
Eu nu as banii pe una noua!
223214742R part number
Nissan qashqai 2008 1.5 doesnt have it rip
Is this job expensive.... Thankyou
No if you do it yourself 😜
@@sandyande I would only break something else
It's a joke after putting a new turbo into my 141 Nissan qashqai and then it was saying under boast so new sensors and pump fitted now I have the C1130 code up the garage who fitted parts told me pip was all cleaned ect and the car has full service history and only 70,000 miles on it 🙈🙈🙈 and just so you know I have 1,600 euros spent so far
Oaft sore one! Sandy
P0471
Can't understand English your English... hahahahaha
It's ok I can't understand Spanish! Cheers sandy
It's Scottish you donk ha ha