Thank you! I was looking for how to set Reverse Mode because our hotel room has this switch installed in the bathroom, so anytime someone uses the restroom during the night, the bright night comes on. There’s already a nightlight in there, so the bright light is just too much. This worked perfectly
Thanks for the video! My sensor has been turning on and off on its own since a few month ago. I just tried fixing it using your method and I just realized that throughout the entire process I didn’t see the green light at all. Does that mean it’s broken? Thanks!
My switch works only works by manually pushing the button. Also I noticed my LED only flashes it’s never on like yours is in the video. Any suggestion? I already tried holding it down for 10 seconds. No chnage
Hmmm. If you've already tried to turn off vacancy mode (4:04) and that's not working, you could try to see if it will turn to any of the other alternate modes to establish if _anything_ works at all. If nothing works, then you've probably got a defective unit (although I've found in most cases, it's just me who doesn't understand how to work the thing). If you're looking for an easier switch to work with, you could try this one from Lutron: amzn.to/3hnBUOo Instructions here: ruclips.net/video/NKJ0RxpqTYo/видео.html
OK, I’m wondering if you can tell me how to wire this .I currently have a Cooper motion sensor it has a black wire a red wire a brown wire and a green wire .I have had it hooked up and it works just fine but it has been hooked up to a fluorescent light fixture on a switch with a three-way, one inside ,and one outside in the garage switch .I have recently purchased a Eaton OSP10M , it has more wires. It has a black wire a green wire a blue wire a orange wire in a red wire. I cannot figure out how to hook this up can you help me?
According to these instructions, it looks like you'd want to tie the black and orange one together, and tie them both to the black (hot) wire: www.davecarter.com/ASSETS/DOCUMENTS/ITEMS/EN/32128_InstallInstructions.pdf
Thank you! I was looking for how to set Reverse Mode because our hotel room has this switch installed in the bathroom, so anytime someone uses the restroom during the night, the bright night comes on. There’s already a nightlight in there, so the bright light is just too much. This worked perfectly
Excellent Video! Very helpful!
Thank you so much for this video!!! So helpful!
Thanks for watching! Glad it helped!
Thanks for the video!
My sensor has been turning on and off on its own since a few month ago. I just tried fixing it using your method and I just realized that throughout the entire process I didn’t see the green light at all. Does that mean it’s broken? Thanks!
Mine doesn’t have any led either. Did you figure it out?
Thanks man!
is there a factory reset procedure so that it will go back to original settings?
Thanks 👍🏽
Missed the part that has wires actually being connected to that switch editor must of screwed up
My light switch won't cut off. Been this way for 3 days. What do I do?!!!!!
My switch works only works by manually pushing the button. Also I noticed my LED only flashes it’s never on like yours is in the video. Any suggestion? I already tried holding it down for 10 seconds. No chnage
Hmmm. If you've already tried to turn off vacancy mode (4:04) and that's not working, you could try to see if it will turn to any of the other alternate modes to establish if _anything_ works at all. If nothing works, then you've probably got a defective unit (although I've found in most cases, it's just me who doesn't understand how to work the thing). If you're looking for an easier switch to work with, you could try this one from Lutron: amzn.to/3hnBUOo Instructions here: ruclips.net/video/NKJ0RxpqTYo/видео.html
OK, I’m wondering if you can tell me how to wire this .I currently have a Cooper motion sensor it has a black wire a red wire a brown wire and a green wire .I have had it hooked up and it works just fine but it has been hooked up to a fluorescent light fixture on a switch with a three-way, one inside ,and one outside in the garage switch .I have recently purchased a Eaton OSP10M , it has more wires. It has a black wire a green wire a blue wire a orange wire in a red wire. I cannot figure out how to hook this up can you help me?
According to these instructions, it looks like you'd want to tie the black and orange one together, and tie them both to the black (hot) wire: www.davecarter.com/ASSETS/DOCUMENTS/ITEMS/EN/32128_InstallInstructions.pdf
I just had my switch installed yesterday and it's on a 3 way. Today it is cycling on and off constantly..
Any thoughts on why?
Thanks
Omg same here and it’s driving me crazy!!!
What if no matter how much time I press it down the light doesn't blink and myblight doesn't turn on?
@@2mpicasso maybe it’s a defective one?
You didn’t show any installations where does the orange red and blue wires connect to
I hate these switches, I need a wiring video so I can rip them out
how about a wiring video