You are wrong when you say after programming you dont touch anything for 30 seconds to finish. If you do that your settings will be NOT save it. You need to push either the top or bottom for 5 seconds to save it.
Thank you Thank you Thank you. You did a great job. I needed this video. This is a great video. The only thing that I can comment on to slow down on talking that we could grab all you say. God bless you man!.
By the way after you change the settings and if you do not hold the top button for 5 seconds then the setting will not save it will exit out the programming mode without the saving your settings so once you change the settings and you wonder why your stuff is not working because you did not say it the changes in this video I believe he failed to mention that but when I was reading the manual I noticed that you have to press and hold the top button for 5 seconds for the settings to be saved
I’m saving it correctly by holding the top or bottom for 5 seconds and it just won’t work. It worked once then randomly factory reset. Does this mean it’s faulty?
I have a black wire(hot), a red and white wire coming out of the wall. The white and red wires connected to the light. I can't figure out how to install this product on this setup. Any guidance?
The LED light remains green all the time on my installation. The switch works great, turns on and off as per settings. It's on a 3 way installation and i have to leave my other switch on if ever i turn it off my sensor switch stops working. Weird problem...thanks for the video helped a lot understanding the settings.
You have to re wire your switch to eliminate this problem. On the 3way switch connect the black traveler to the black power/line wire together. So there should be 2 wires on the common screw and the red wire on the other screw
Great video. I will not recommend this switch. I read the instructions program the switch it won't turn off as programmed. Thought I was doing something wrong. Watched this video which is a great tutorial but yet the switch would not turn off on time set.
I’m an electrician and I’ve installed many of these and they’re all pieces of garbage, nothing beats the old style turn on turn off, no decrease in sensitivity no decrease in ambient light, etc… if you want a customer to call you back 50 times regarding their lights turning on, by the switch, you’ll make a new friend
You are wrong when you say after programming you dont touch anything for 30 seconds to finish. If you do that your settings will be NOT save it. You need to push either the top or bottom for 5 seconds to save it.
Thanks for chiming in! I'll pin this comment to the top in case anyone else is having similar trouble.
Yes you have to press and hold top button for 5 second to save and exit. Do not just leave it alone it will do nothing
Will turning off the light manually disable the motion sensor?
Yes
YES!!!!!
Tracked my head on this and lost an hour of my life that I will never get back
This switch is a POS
Best video I've seen on this product. Thank you sir
Glad to hear it! Good luck!
Thank you Thank you Thank you. You did a great job. I needed this video. This is a great video. The only thing that I can comment on to slow down on talking that we could grab all you say. God bless you man!.
By the way after you change the settings and if you do not hold the top button for 5 seconds then the setting will not save it will exit out the programming mode without the saving your settings so once you change the settings and you wonder why your stuff is not working because you did not say it the changes in this video I believe he failed to mention that but when I was reading the manual I noticed that you have to press and hold the top button for 5 seconds for the settings to be saved
Thank you. You said it right. Now it's working
Excellent, well done, easy to follow.
Thanks for the kind words!
I was going mad while trying to do this with just the instruction sheet, tks a whole bunch.
Glad I could help! I know what you mean. Most of those instruction sheets are terrible.
Awesome video thank you and thank you… and yes we need hold the top button to save the changes
Thanks for explaining this in detail. The instructions are a bit confusing, or I'm just really stupid.
You are not stupid! All of these instructions are confusing.
@@sethwilliams43 I've tried and tried and tried numerous times and I still can't get it to the setting I want it at
I almost went crazy for a min! Thank you!!!
You're welcome!
ufff, was going nuts for day or two doing this a part time, finally got it, must be hold 5 sec to save ALL changes.
Thank you! Saved my day!
Happy to help!
Awesome video 👍
dos = Decora Occupancy Sensor / 02 means 2 Amps / -L = the green LED on the face / W = white
Ah, I see. So it's like a code. Good to know!
thank you
Great video!
Just to be clear.. so the light won't turn on if motion is detected, you have to manually turn it on first correct?
Yuuup, Yes 👍🏻. I just viewed your very clear informative video clip, Thanks I Appreciate It 😎.
Thank You!
Thanks very much 🎉
I’m saving it correctly by holding the top or bottom for 5 seconds and it just won’t work. It worked once then randomly factory reset. Does this mean it’s faulty?
I have a black wire(hot), a red and white wire coming out of the wall. The white and red wires connected to the light. I can't figure out how to install this product on this setup. Any guidance?
The LED light remains green all the time on my installation. The switch works great, turns on and off as per settings. It's on a 3 way installation and i have to leave my other switch on if ever i turn it off my sensor switch stops working. Weird problem...thanks for the video helped a lot understanding the settings.
You have to re wire your switch to eliminate this problem. On the 3way switch connect the black traveler to the black power/line wire together. So there should be 2 wires on the common screw and the red wire on the other screw
Can this be used (with timer) to turn off restroom fan after someone takes a dump?
Very nice
Mine doesn't have a switch for occupancy or vacancy. Is mine manufactured badly?
How do I turn timer off. So lights only turn on and off by me hitting switch.
How do I set it to go off when I walk in lol I can’t figure it out
Muy bién explicado .
Muchas gracias.
I got mine all connected...it turns on then off in one second. when I press the button...the lights won't stay on. Suggestions??
Thank you
You're welcome!
My switch dosent have the vacancy little switch i just see the square but no switch, is there a cover i have to remove????
Yes, you can remove the whole cover. You should be able to pry it off from the bottom of the switch cover.
I know this video is 2 years old but can you go and fix those face plate screws. It's screwing with my OCD.
Ah, so sorry about that. I'll remember that if I ever make another one of these. :)
Red light not coming on. 🤔
What if the lights dont turn on at all?
Mine won't turn on automatically, lol No matter what I've tried...
Thanks!
Why doesn’t my light turn at all when I push the button ?
Same with me, I want to find out so badly
Great video. I will not recommend this switch. I read the instructions program the switch it won't turn off as programmed. Thought I was doing something wrong. Watched this video which is a great tutorial but yet the switch would not turn off on time set.
Did you ever solve it?
Mine won't turn on automatically, lol No matter what I've tried... (taking it back tomorrow)
@@jeffreygriffith9803 I have the same issue. Can't figure it out. Tried adjusting the light sensitivity but no luck no matter what I do.
If you remove the front color kit and plate to access a switch where you can pick between Occupancy or Vacancy. 2 differents settings
I’m an electrician and I’ve installed many of these and they’re all pieces of garbage, nothing beats the old style turn on turn off, no decrease in sensitivity no decrease in ambient light, etc… if you want a customer to call you back 50 times regarding their lights turning on, by the switch, you’ll make a new friend
My light is off
No matter what I do mine just comes on and then immediately turns off.
I have the same issue. Were you able to solve this?
same issue any resolution
Reset your switch removed from the power and press up botton and down botton at desametime for 5sec. Put it back the wire