VERY GOOD VID, YOUR APPROACH TO LAYING DOWN CARBON FIBER VINAL OR ANY OTHER VINAL FOR THAT MATTER MADE MY LAST FEW JOBS GO MUCH MUCH BETTER!! THANKS, MY HAT,S OFF TO YOU!!!
True, they are build in Oxford (except the Countryman and maybe some others). But i would call it more an English/German/French hybrid these days. The technic and the engine are very very similiar to BMW/Peugeot.
You have to remove the air intake and open the bonnet so you can wrap the vinyl not only up to the edge....like you do it with the chrome part or the air intake in front of the windscreen. And if someone cuts of the vinyl on my mini like you do, he would have touched my car once and not again ;-)
Use a couple of drops of dish washing liquid in a squirty bottle and spray it on the back of the vinyl (sticky side)Then apply the sheet to the hood. with hard plastic squidgy, starting from the center on a 45° angle draw the squidgy to the edge of the sheet, removing as much liquid as you can. End result, totally flat no air trapped and not pissed off. Do not do this on a hot surface as the liquid will dry too fast.
Well for one, it cost a lot less than having it painted and still looks professionally painted. Secondly, if you sell the car, the new owner can simply remove if desired. Just have the surface polished rather than pay it have it repainted. $ saved ☺
I have to say your skill is freaking amazing. but I have a question, I am looking at doing my own stripes because i'm broke and my local shop is retarded and sucks at vinyl stripes. HOW would you go about getting the vinyl into a depth area like the trunk of a 96 ford mustang? I am ready to begin doing this, but i am really worried about the trunk.
I was planning on using that brand, type but I can't find 1/4" rolls to use on the outer edges, as most cars have. I would be turned off if it was not made and it could only be done by cutting it yourself, I think it wouldn't turn out neat enough. I see aftermarket carbon stripe kits which have it, and it's hard to understand how that would work unless there is clear film under the material. Please explain?
The first engines were manufactured by Tritec, a joint venture of Chrysler and BMW. Later minis have an engine of the PSA-Group insinde. Not a real bmw ;-)
i have this bubbles problem when i installed the 3m carbon fiber on my car's hood can u please tell me how to install it with out any bubbles ? it pissed me off
For the record. BMW stands for Beirische Motor Werke and is defenitely an of origin german company. I also want to do my car but it has so many curves that it will be 300% harder than this video. Here the hood doesn't curve much.
Di-noc is not rated for exterior application on a vehicle, and a proper install with no stretch should not ever lift up especially in that area. We at CJC Wraps use primer on very difficult areas but we dont recommend using it on flat/useless places usually only use it on one or two spots on a whole car. get 3m 1080 carbon fiber, and a professional who's been doing wraps for a few years, oh and cutting on the paint. . . even as a professional I dont do this :( knifeless tape man, knifeless tape
could you make a video of that to show that you actually have something of substance to contribute? Do you believe that your comment contributes anything worthwhile? What were you hoping to receive leaving this comment?
3m primer on the paint? what if you pull it off, you ruined the paint job! It's 3m you don't need to put in on the top, only under the hood. Should use a soft tip squeegie as well because you just scratched the paint and the vinyl.. Otherwise it looks good!
Ecco come fare in modo che nessuno venga li! Nessuna pulizia delle supersici pochi istanti prima dell'apllicazione per eliminare le impurità! Non si vede l'uso di un metro o di un calibo: tutto a occhio! Si smonta la maschera frontale, si attacca qualche cm di pellicola sotto nella parte nascosta e poi si rimonta la maschera. Stessa cosa alla fine del cofano! Altrimenti si riscia il distacco sui bordi... Complimenti per la poca precisione!
VERY GOOD VID, YOUR APPROACH TO LAYING DOWN CARBON FIBER VINAL OR ANY OTHER VINAL FOR THAT MATTER MADE MY LAST FEW JOBS GO MUCH MUCH BETTER!! THANKS, MY HAT,S OFF TO YOU!!!
You did a good job.
Thanks for showing us how you did it.
Actually, you can buy it on amazon, its 3M Di-Noc carbon fiber vinyl, and im pretty sure its the same as any vinyl wrap
Very cool, I wouldent have thought to do this how you did it. Think I'll do this when I put my own stripes on
True, they are build in Oxford (except the Countryman and maybe some others). But i would call it more an English/German/French hybrid these days. The technic and the engine are very very similiar to BMW/Peugeot.
You have to remove the air intake and open the bonnet so you can wrap the vinyl not only up to the edge....like you do it with the chrome part or the air intake in front of the windscreen. And if someone cuts of the vinyl on my mini like you do, he would have touched my car once and not again ;-)
MCSRoehric
Fantastic video guys, we use the 3M carbon fibre to wrap our clients cars and it always looks incredible.
Nice technics. Also looks nice.
definitely no ordinary vinyl graphic.
What exactly did you brushed on the hood at the very beginning process?? BTW sweet tunes!
Adhesion promoter
I have a 2011race red five liter mustang, how would those look on my car ? Nice job BTW.
Bavarian Motor Works BMW is a Germain company Bavaria is a state of Germany where the HQ of BMW is located.
All the effort but you didn't remove the intake?
Use a couple of drops of dish washing liquid in a squirty bottle and spray it on the back of the vinyl (sticky side)Then apply the sheet to the hood. with hard plastic squidgy, starting from the center on a 45° angle draw the squidgy to the edge of the sheet, removing as much liquid as you can. End result, totally flat no air trapped and not pissed off. Do not do this on a hot surface as the liquid will dry too fast.
shouldn't the pattern of the strip on the driver side go the other way?
nice work
love it
Wow. Looks great.
You makes it so easy....
Well for one, it cost a lot less than having it painted and still looks professionally painted. Secondly, if you sell the car, the new owner can simply remove if desired. Just have the surface polished rather than pay it have it repainted. $ saved ☺
DaytonCarCare DaytoncaRcare
DaytonCarCare 😀😀
is having racing stripes on a MINI would consider "ricer" since MINI are not really racing cars?
i like the way you pimp vehicles i would want to do the same ,iam in Nakuru kenya ,how do i get the stickers
looks fresh
The 2nd track was the Jam
I have to say your skill is freaking amazing. but I have a question, I am looking at doing my own stripes because i'm broke and my local shop is retarded and sucks at vinyl stripes. HOW would you go about getting the vinyl into a depth area like the trunk of a 96 ford mustang? I am ready to begin doing this, but i am really worried about the trunk.
Nice work. To bad that the intake in the front doesn't match the carbon stripes ;-)
I was planning on using that brand, type but I can't find 1/4" rolls to use on the outer edges, as most cars have. I would be turned off if it was not made and it could only be done by cutting it yourself, I think it wouldn't turn out neat enough. I see aftermarket carbon stripe kits which have it, and it's hard to understand how that would work unless there is clear film under the material. Please explain?
How does this hold up in high heat, high humidity places? My car will bake in the sun all day while I am at work 8 to 10hr.
Yeah, What is the width of the stripes?
example i want to remove ittt how i do ittt?????
Justin ❤
I got answers to my questions in my previous post, but got another, is that the glossy or matte version?
you really helped me
thanks!!!!
whats the size of the stripes and whats the distance between the stripes?
The first engines were manufactured by Tritec, a joint venture of Chrysler and BMW.
Later minis have an engine of the PSA-Group insinde.
Not a real bmw ;-)
I would have aligned with the outer edges of the hood scoop
was it hard to do the bottom part of the bumper?
good job mann :)
i have this bubbles problem when i installed the 3m carbon fiber on my car's hood can u please tell me how to install it with out any bubbles ? it pissed me off
Imma put these on my minivan.
not only would be better to put a tape in the middle?
nice job
Jorge Cuéllar Alvarez
ชอบ
How long does this stuff stay on?
What's the second song that plays?!?
For the record. BMW stands for Beirische Motor Werke and is defenitely an of origin german company.
I also want to do my car but it has so many curves that it will be 300% harder than this video. Here the hood doesn't curve much.
como se llama ese pegamento q lleva en los bordes?
NEVER put your fingers in front of a heat pistol kids
What about removing these? Is it also as easy as this looks?
Di-noc is not rated for exterior application on a vehicle, and a proper install with no stretch should not ever lift up especially in that area. We at CJC Wraps use primer on very difficult areas but we dont recommend using it on flat/useless places usually only use it on one or two spots on a whole car. get 3m 1080 carbon fiber, and a professional who's been doing wraps for a few years, oh and cutting on the paint. . . even as a professional I dont do this :( knifeless tape man, knifeless tape
Joe Chlanda joechianDa
What kind of music is this?
ɷɷɷ Heeey Friendsssss I Have Foundddd Workingg Online Hacck visittttt : - t.co/DpGBarCUaA
personally i would have masked and painted the stripes must be an easier way
Con LumaMex light background en the wrap
The watch could be a problem
ur ryt,look like a beginner 4me.
what car do u hv that is more curvy than a mini? lol
Alan Bolanon 55 Belair
Faltou usar luva... para ser um serviço profissional...
you need to spend some money on a good stainless steel olfa knife
padre
94 squirrels dislike it.
could you make a video of that to show that you actually have something of substance to contribute? Do you believe that your comment contributes anything worthwhile? What were you hoping to receive leaving this comment?
muito mais fácil aplicar com agua e usar uma trena para alinhamento
9:05 sl 55 ?
3m primer on the paint? what if you pull it off, you ruined the paint job! It's 3m you don't need to put in on the top, only under the hood. Should use a soft tip squeegie as well because you just scratched the paint and the vinyl.. Otherwise it looks good!
No tiene ni idea!!!!
ang pogi ko!!!!
Ecco come fare in modo che nessuno venga li! Nessuna pulizia delle supersici pochi istanti prima dell'apllicazione per eliminare le impurità! Non si vede l'uso di un metro o di un calibo: tutto a occhio! Si smonta la maschera frontale, si attacca qualche cm di pellicola sotto nella parte nascosta e poi si rimonta la maschera. Stessa cosa alla fine del cofano! Altrimenti si riscia il distacco sui bordi... Complimenti per la poca precisione!
The heart of a Mini is french... *gg
falto expediencia so!!!!!!!!!!!!!!
In 2 months that job will be worthless... Very bad methods used to stick.
They're* and they're British, as they're owned by BMW. British Motor Works.
A VANIA TA CANSADA RSRSRS
Allen Robert Moore Gary Thomas Helen
DO NOT USE THE ADHESIVE PROMOTER. It is a nightmare to get off, and completely unnecessary especially in this situation.
quitate esos audifonos creo k no te ves como profesional!
do you have Not professional
its actually a Lamborghini...lol
nice racing strip on a fuking slow mini
serge933 - Compared to?
Yeah slow compared to what? A proper race car? Yeah know shit.
Mini's make you look like a prat.. Mini's with fake carbon fiber... Bigger prat
what the hell? this is pernament
kelamaan
Why the hell did you just do that to your car? That's so fucking cheap.
nice job but you choose the gayest songs to post
padre