Jorge, thanks so much for the videos, outstanding contribution! Question: You seem to start your video with an AP in Lightweight mode, which you manage to convert to Autonomous mode, right? But the video shows that you can enter "configuration terminal" and run other commands before the conversion. I have a Cisco Aironet 2600 Series in Lightweight mode (exactly like the one at the beginning of your video), yet, I cannot enter configuration terminal.... I cannot even use the ping command.... it just doesn't work. Someone in a Cisco discussion commented this: "I believe there is no conf t option, as it's all done via the controller." Here is the link to that discussion: community.cisco.com/t5/other-wireless-mobility-subjects/unable-to-go-in-configure-terminal-mode-in-cisco-ap/m-p/2475494/highlight/true#M63020 If the above is true, how can you enter those commands in an AP which is in Lightweight mode?
sir i am unabale to download cisco 1532e autonomous ios .as i have no permission to download. can you help me and download this file for me and send me
Hi thanks for the video but not sure what I am doing wrong but I have tried this many times and I keep getting an error (archive download-sw /overwite /force-reload tftp://192.168.1.54/c1140-k9w7-tar.1^24-25d.JA.tar % Invalid input detected at '^' marker. I fyou could point me in the right direction I would appreciate it.
i did the same for the , cant see tftp doing anything and cisco stay still for about 35 second and message back was "archived completed in 35 second" that's all
![GEEK TIMË [OFFICIAL AUDIO]](http://i.ytimg.com/vi/ry-6RvkH880/mqdefault.jpg)
Dude! I spent the last two days trying to figure this out. Thank you! You Rock!
Jorge, Thanks so much for the videos.
Great video. thanks. Everytime the "renew DHCP" message comes up it forces my tftp copy to timeout - any tips?
Jorge, thanks so much for the videos, outstanding contribution!
Question:
You seem to start your video with an AP in Lightweight mode, which you manage to convert to Autonomous mode, right? But the video shows that you can enter "configuration terminal" and run other commands before the conversion.
I have a Cisco Aironet 2600 Series in Lightweight mode (exactly like the one at the beginning of your video), yet, I cannot enter configuration terminal.... I cannot even use the ping command.... it just doesn't work.
Someone in a Cisco discussion commented this:
"I believe there is no conf t option, as it's all done via the controller."
Here is the link to that discussion: community.cisco.com/t5/other-wireless-mobility-subjects/unable-to-go-in-configure-terminal-mode-in-cisco-ap/m-p/2475494/highlight/true#M63020
If the above is true, how can you enter those commands in an AP which is in Lightweight mode?
muy buen aporte, realizaré mañana haber como me va
regreso!
What are the main differences between lightweight and autonomous?
Hi could you please send me the software. I cant get it from Cisco. Is this for a 2602 if not will it work on that model?
Started great but during the transfer and install, I'm getting a message that IPv6 tries to get configured and the replacement fails... any idea?
Any help to take an AP1130-AG that is running a recovery image that looks like the mode button has been disabled to convert to an autonomous mode?
sir i am unabale to download cisco 1532e autonomous ios .as i have no permission to download. can you help me and download this file for me and send me
Hi thanks for the video but not sure what I am doing wrong but I have tried this many times and I keep getting an error (archive download-sw /overwite /force-reload tftp://192.168.1.54/c1140-k9w7-tar.1^24-25d.JA.tar
% Invalid input detected at '^' marker.
I fyou could point me in the right direction I would appreciate it.
Anytime I try to ping my network it fails kindly assist
i did the same for the , cant see tftp doing anything and cisco stay still for about 35 second and message back was "archived completed in 35 second" that's all
I had a hard time with tftp i ended up transfering with xmodem over serial its super slow but it works!
Zaxaz1990 try to disable firewall for the start
Can you give me the 15.3.3 firmware? i dont have a cisco login
bro u have this fw? can send me also afajarillo@gmail.com. tnx in advance
Hi, can send me please also to vocestres@gmail.com?
good. i create same video in my channel.