Piping Double Rolling calculation | Updated
HTML-код
- Опубликовано: 3 янв 2019
- This video explain How to calculate Piping rolling calculation (Vertical rolling and Horizontal Rolling) by using Pythagoras Theorem
Newly Updated exercise..Watch,Share and comment....
#pipingformula #technicalpiping #pipingrolling
Watch More Piping videos...
1.Layout and Development of Pipe Branch 90 degree : • Layout and Development...
2.Piping_How to read isometric drawings_Basic : • Piping_How to read iso...
3.Pipe wall thickness calculation as per ASME B31.3 : • Pipe wall thickness ca...
4.Piping_Fabricate 45 Degree Elbow(miter bend) from pipe : • Piping_Fabricate 45 De...
5.How to fit up pipe to 45 deg elbow? : • How to fit up pipe to ...
6.How to fit up pipe to flange? : • Piping symbols In isom...
Sir, thank you for understanding the difficulty of the new learner and simplified the complex concept very easily. Thank you so much . I am waiting for another new video
I like this video.
I watched it more than a half a dozen times.
IT CONTAINS MANY GOOD POINTS!!!
You accurately demonstrate 3 of the 6 trigonometric functions.
All of your math is correct for any 2 dimensional triangle.
The problem which I see in this video is that 2 dimensional trigonometry does not accurately explain trigonometry in 3 dimensions. Compound rolling angles must be computed anytime that you are working in 3 dimensions.
Even though this appears to be a 2 dimensional problem, as soon as the 3rd dimension is included (the roll) all bends now become compound bends. 1 bend is now doing what 2 bends would normally do in 2 separate planes.
For anyone to easily visualize your diagram, get yourself a rectangular box.
A rectangular box of facial tissues will work.
Place your tissue box on a table in front of you, with the flattest side down, and the 2nd flattest side facing you.
Label your 3 dimensions onto that tissue box. The 800 will be written along the width of the front. The 214 will be written along the depth of the box. The 73 will be written onto the height of the box. 3 DIMENSIONS!
Now poke two pencils into the box, at the points where your 3" pipe would enter and leave the box.
For simplicity of understanding, rotate your box so that it matches Figure 22 on page 65 in the book: Tube Bending Simplified (available from Amazon.com or E-bay.com).
Now follow the crystal clear explanation in the chapter COMPOUND LENGTH AND BEND on pages 65 through 69 in the book Tube Bending Simplified.
After doing the easy to follow calculations, you will find that both of the fittings on the 831 mm center to center piece are 75.5 degree fittings.
A 3" standard 90 degree elbow has a 4-1/2" radius.
If you turn to page 13 in the book Tube Bending Simplified, under the 4-1/2" radius chart, you will see that a 75 degree bend has a face to center measurement of 3-7/16". Pretend that these are 75 degree bends, instead of 75.5 degree bends.
Your 831 mm travel - (3-7/16 + 3-7/16) will equal 831 - 6-7/8 to equal an end to end pup piece of 824-1/8 mm.
Hi, thank you for this explanation. I found an angle of ~15.7° (√ 214^2+73^2 = 226, then atan (226/800) = 15.7°). I found other videos where they take the value of the angle, 15,7 ° in this case, as base angle to determine the face to center measurement (0.6'' with 15°, instead of 3-7/16 for 75°). Could you please explain ?
Got it Todd! TY
Now your calculation is everything okk. Excellent 👍👍👍👍.
Best ever explanation.thanks much
Best tutor about rolling pipe ,thank u very much sir
Really this is great knowledge about rolling
Thanks, very useful 🌷🙏
V...nice information Sr. .
Best explanation of piping degrees
Thank you 🙏
You videos are great , i couldn't see the pipe marking video
Very very useful brother..thank you
Thanks brother🙏❤❤ very useful 🌹🌹
Good knowledge full video.
Good Information Sir
Thank u brother ❤️
👌👌👍👍
Very useful
Plz make video on how to find travel length for double rolling in feild measurment
Good information
👍👍
Thank you very much
So very important and thank you so much
You are most welcome
hola amigo doy reciente en este rubro ayúdeme haga un vídeo en español sobre el mismo tema, esta muy interesante . muchas gracias
please upload more sample rolling. thankyou
Thank you for
Welcome
Amazing
Thanks
Super
Buen video pasar español
intentaré
Nice
sir one doubt
how did you get 88.9mm outder diameter from 3 inch pipe
please reply me
3'' NB PIPE IS 88.9OD THIS IS THE STANDARD SIZE. YOU CAN PUT A BSPP THREAD ON THE END OF THIS PIPES,THATS THE REASON FOR IT.
Easier: hypotinuse = √ 800² + 214² + 73² , then find angle between adjacent and hypotenuse with formula αº = tanˉ¹ ( 73 / √ 800²+ 214²)= 5.04º or between opposite and hypotinuse by Βº= tanˉ¹ ( √ 800²+ 214² / 73) = 84.96º and rotation of flange like shown in video.
your formula is nice that is so easy
short formula good to use when talking about production..i have also my own formula short formula also thanks for onather formula you shown..
How’d you get those symbols mate
Any job is available in this field... I am a good layout engg
7:49 da li postoji mogucnost da bude prevedeno na srpski jezik.Video je izuzetno dobar i veoma detaljan
Sir degree agar deffrent ho to double rolling Ka travel kaise find out karenge please
Sir plz explain me I have one doubt ?
You calculated 11.5 mm from the values of 800,214 and it's using flange side... At the same time you calculated 5degree also have to use flange side .... How its use 85 degree flange side ??
How about 4" rolling 45°? What is the formula?
Bro now it's CRT
Suoer
How is it finded 3 inch pipe od as 89?????
Its as per ASTM pipe standards dimensions...
It's ok
how you suddenly get hypothenius 831 ?
Its given in drawing. watch video clear.thanks.
If that value not given. no issue. can find value it using any one of the formulas given here. Watch 1:37
In (1) = Horizontal rolling we shall use the Sin relationship not the Tan one.
Ise awaj dekar samjhaye
Bina rolling dikhaye kisi isometric drawing pe ek video banao bhai
Hame kaise smjh me aayega ki rolling kaha h
Ye question aaj mujhse Oman ke liye diye gaye interview me puchha gya tha
Plz reply
ok
What's mean CR on Flange CR?
Sir ,how to find distance 831 mm ?
831 given in drawing (elbow center to center distance).
If that value not given.no issue. can find value it using any one of the formulas given here. watch 1:37
Tan =add/hyp
No,Tan = opp/adj
Здравствуйте Хороший видео но непонятно что вы говорите сделать русский перевод пожалуйста Спасибо заранее
спасибо, в следующий раз я сделаю лучшее видео.
@@TECHNICALPIPING Спасибо за понимание
You mentioned in the formula wrong in the tan : opp/adj,
Yes,But its edited correctly.watch one more time....thank u...
831 hw it came in vertical rolling
Its given in drawing.
If that value not given.no issue. can find value it using any one of the formulas given here. watch 1:37
π×D/360 ???????
Circumference divided by 360 ...... U will get one degree value...
3.14×89=279.5 cf divided full degree, 279.4÷360=0.77 it's value 1 degree
شكرا لك
With this formula... Convert degree into mm
関数電卓使ったら🎵(笑)❕🤣
はい
@@TECHNICALPIPING 余計な事言ってゴメンね🎵多分同業者だと思います。これからもお互い頑張りましょう😀👍
音楽について言うのですか？
@@TECHNICALPIPING sorry. I don't understand.
hi kayama,What you do not understand is this video.
Bol ke samjao koi Hana thori h Jo aap music Dali ho keya .....
Video no celerate
По русски можно
How u sloved or do calculations without speaking.. If u can't speak then I no need to make vedio
watch this video for to know more details about pipe rolling ruclips.net/video/1YJD0W78oaw/видео.html
노래틀고 혼자 공부하노? 설명도 없이?
Nice