Ottimo lavoro, complimenti! E' molto interessante vedere come nasce un gioiello ed io, poi, ho un debole per i bracciali e questo è davvero bello. Con entusiasmo attendo altri video come questo. A presto.
on you polishing wheel. is the wheel on the right a rougher one? if so what kind is it i need one. i love this link it looks easy and very nice. this will be my first link i try. i have trouble soldering those ring together though. i tried this with silver. I'm not done yet but i feel if i put the work in it might as well be gold.
to polish, use two different brushes with two different types of pasta. A brush is made with hard hair and is used with an abrasive paste. The other is a cotton brush that is used with a polishing paste
Very very inspirational for a beginner like me , I would like to ask when you solder the lobster claw won't the spring inside the claw (lock) get damaged as I tried with silver lock of this type and the spring mechanism got damaged , please provide your valuable knowledge, once again thanks for posting these valuable vedios From :Kashmir (India)
It is because silver transfer heat really good. When you heat the jump ring, heat goes through it to the clasp and to the spring. Gold does not transfer heat as good as silver so you can solder jump rings without removing the spring. Also using small flame helps. I am using oxy-propane torch with needle tips so I soldering jumprings even on solder isnt a problem. But I dont solder them - it takes too much time(solder, pickle, polish) - instead I use PUK to weld them quickly :)
Привет Коллега! Смотрится симпатично! Тебе не кажется, что браслет получился жёстким? Тебе конечно виднее! По-моему, в готовом браслете, звенья должны быть свободнее. Мне кажется Ты его перетянул через фильеру. Как исправляешь ход звена?
Коллега согласен с вами,браслет слегка деревянный,я бы спилил бока слегка,придал так сказать форму а то на мой взгляд не полноценный,это на мой взгляд, а может клиент так захотел.
HorRnuS T524ET Здорова были, как-то раз слышал от своих коллег, за Ювелира, который камень шипом наверх закрепил. Тем самым объяснив клиенту, что он художник ему виднее. 😎
Immediately after passing through the trap, it remains very rigid. During polishing, using the abrasive paste, I consumed slightly the thickness of the meshes, this I used to make the bracelet soft enough to be worn.
Scaffolding is there anyway you could make me one of those 18 inch 18kt gold chains and the bracelet in 18kt gold 8 inches to match it just tell me how much u will charge me for both???
it is antioxidant and fluidizing. it is in liquid form, with the flame it is taken out and forms a protective white patina, which helps the solder to flow. from the goldsmith's wholesalers you can find different brands
The proportions of copper and silver in the gold alloy at 750 thousandths (18KT gold) depend on the color that you want to get. 2 silver and one third of copper you will have the yellow color, increasing the copper and decreasing the silver you will have all the nuances until you get to the English red.
Absolutely stunning!!!! A true artist.
Nice draw plate technique Scaff!
Thanks
Your videos are awesome. Master jeweler and craftsman!excelente amigo
Thanks
Brilliant. More more more please !!!
I have learnt so much from your videos. You are a legend
thanks a lot
LINDO BRACELETE MUITO BOM! !! COMO SEMPRE PARABÉNS AMIGO SCAFFOAL!!!!!
thanks for the video. I'm learning a lot from you. I've used several of your techniques in my latest custom projects.
Thank you. This makes me happy
Ottimo lavoro, complimenti! E' molto interessante vedere come nasce un gioiello ed io, poi, ho un debole per i bracciali e questo è davvero bello. Con entusiasmo attendo altri video come questo.
A presto.
Grazie
Unbelievable! It's so beautiful!! 👍👍
Thanks
excelente video!! gracias por compartir, aprendi mucho! podría preguntar que calibre utilizaste en este brazalete?
man I love that stretcher
thanks
Really enjoyed the video! Nice work and well filmed!
Just a question: that lobster claw - did you make it yourself or bought a factory made one?
The hooks I use already made from the factory.
Beautiful work 👍
thanks
Gorgeous!
Thanks
Привет!
Отличная работа. В этой цепи очень красиво три цвета метала, хорошее решение!
спасибо
Thank you again for sharing your knowledge and skills.
Thank you
you are the master!!
Thanks
Can you tell what length, thickness wire do you use?? What radius are the rings for making chain??
Beautiful! You use the same solder (white) for each color metal?
Not every color has its welding
Awesome 👌
thank you !
What percentage of care that you use to solder jewelry in 18 k gold?
on you polishing wheel. is the wheel on the right a rougher one? if so what kind is it i need one. i love this link it looks easy and very nice. this will be my first link i try. i have trouble soldering those ring together though. i tried this with silver. I'm not done yet but i feel if i put the work in it might as well be gold.
to polish, use two different brushes with two different types of pasta. A brush is made with hard hair and is used with an abrasive paste. The other is a cotton brush that is used with a polishing paste
Muy bueno, me ha gustado la técnica
gracias
Can you tell me melting detail and solder melting detail also for 18k gold
nice work!
Thanks
Your works remind me of Yaring Platero's.
It's a pleasure to see you work. Where can I buy that bracelet?
you can contact scaffoal@oro-diamanti.it
21.veri God.
Can you please do a video on how to make Cuban link chains
Wow awesome work!! Is there any way I could get a price on this but in a 22” chain in just yellow gold?? Everyone charges so much
You can contact scaffoal@oro-diamanti.it for information, thanks
scaffoal I did but no reply
Magnifico!
grazie
Nice i like it
thank you
Very very inspirational for a beginner like me , I would like to ask when you solder the lobster claw won't the spring inside the claw (lock) get damaged as I tried with silver lock of this type and the spring mechanism got damaged , please provide your valuable knowledge, once again thanks for posting these valuable vedios
From :Kashmir (India)
It is because silver transfer heat really good. When you heat the jump ring, heat goes through it to the clasp and to the spring. Gold does not transfer heat as good as silver so you can solder jump rings without removing the spring. Also using small flame helps. I am using oxy-propane torch with needle tips so I soldering jumprings even on solder isnt a problem. But I dont solder them - it takes too much time(solder, pickle, polish) - instead I use PUK to weld them quickly :)
Our colleague provided a precise explanation. Thanks
Привет Коллега! Смотрится симпатично! Тебе не кажется, что браслет получился жёстким? Тебе конечно виднее! По-моему, в готовом браслете, звенья должны быть свободнее. Мне кажется Ты его перетянул через фильеру. Как исправляешь ход звена?
Коллега согласен с вами,браслет слегка деревянный,я бы спилил бока слегка,придал так сказать форму а то на мой взгляд не полноценный,это на мой взгляд, а может клиент так захотел.
Коллега, он перетерал , мудохолся парень.Нужно после каждой перетяжки смотреть.
HorRnuS T524ET Здорова были, как-то раз слышал от своих коллег, за Ювелира, который камень шипом наверх закрепил. Тем самым объяснив клиенту, что он художник ему виднее. 😎
Юра Кориш правильно говоришь!
Immediately after passing through the trap, it remains very rigid. During
polishing, using the abrasive paste, I consumed slightly the thickness
of the meshes, this I used to make the bracelet soft enough to be worn.
Nicely done
thank you
Maestro salve, se non sono troppo indiscreto mi può dire il peso del bracciale? Grazie anticipatamente.
Scaffolding is there anyway you could make me one of those 18 inch 18kt gold chains and the bracelet in 18kt gold 8 inches to match it just tell me how much u will charge me for both???
Could u please tell us what is that white powder called the powder u use while flaming the chain?
it is antioxidant and fluidizing. it is in liquid form, with the flame it is taken out and forms a protective white patina, which helps the solder to flow. from the goldsmith's wholesalers you can find different brands
Maestro complimenti per il bracciale.
Grazie
How do you polish red, white and yellow gold, as white gold needs rhodium plating??
I use polishing pastes that I find from the "Luigi dal Trozzo" company. The rhodium bath is used to make white gold even more white
Amazing work. I what to be your student.👏👏
Thanks, now I can not teach.
Very nice work
Thanks
scaffoal is the best
Thanks a lot
good job
Please I need help
What are the quantities of the 18K gold welding mix?
Using 18kt welds, the proportions are 75 pieces of pure gold and 25 pieces of solder alloy that you purchase from LEGORGROUP
scaffoal
What are the welding alloys? Do you mean cadmium?
It all looks so easy but I know it's not....So awesome. :)
Thanks
Creativity⛓️👨🎨🌹
Thanks
Can you order a custom ring from you?
Yes, you can contact scaffoal@oro-diamanti.it
for 18k how much copper have you mixed
The proportions of copper and silver in the gold alloy at 750 thousandths (18KT gold) depend on the color that you want to get. 2 silver and one third of copper you will have the yellow color, increasing the copper and decreasing the silver you will have all the nuances until you get to the English red.
Nice
Thanks
plz making silver and gold joind meteril
Ok
I love your videos. Like and subscribe.
Thanks
damn cuantos languages parla??? impressionante signore 5,6??
how can buy how much
you can contact scaffoal@oro-diamanti.it
How much
you can contact scaffoal@oro-diamanti.it
I apologize in what way you can place an order for a bracelet equal to the video
You can contact scaffoal@oro-diamanti.it
can i take it please
you can contact scaffoal@oro-diamanti.it
Shop no
Hello, I have emailed you but no reply yet
I think I answered yesterday sorry for the delay
No I haven’t got a reply.
El contenido muy bueno pero la música nada ke ver
ok
هذا العمل خطاء لانه سوف يكون ثقيل الوزن
إنها ثقيلة لأن العميل يريدها ثقيلة