Replacing Broken JST Connectors On Flight Controller

The JST connectors are pretty damn annoying. We complain about them being in the way then we complain after they break off and are no longer in the way. But here is how to fix your flight controller to be as good as new.
Tools I use for repairs
Amazon.....................................
Hot air gun - amzn.to/2lmUdmR
Flux paste - amzn.to/2mD57Xl
Solder paste - amzn.to/2mqY7QJ
Solder wick - amzn.to/2ln5jbl
Helping hand - amzn.to/2mbqCB6
Flux cleaner - amzn.to/2mbokSC
Banggood.................................
Hot air gun - www.banggood.com/858D-220V-Hot...
Flux paste - www.banggood.com/BON-102-Flux-...
Solder paste - www.banggood.com/XG-Z40-10cc-S...
Solder wick - www.banggood.com/Wholesale-5-F...
Helping hand - www.banggood.com/4X-helping-Ha...
Ebay..................................
Hot air gun - rover.ebay.com/rover/1/711-53...
Flux paste - rover.ebay.com/rover/1/711-53...
Solder paste - rover.ebay.com/rover/1/711-53...
Solder wick - rover.ebay.com/rover/1/711-53...
Helping hand - rover.ebay.com/rover/1/711-53...
Repairs playlist - • Repairs Playlist
All my playlists - / @projectbluefalcon
Video editor - amzn.to/2n7sUiF
My personal vlog channel - / jcofficial3

[@hydrojedi]

Amazing how often I find myself coming back to this great channel! You're missed greatly...and still helping!

[@jasonromair]

Man I thought the same thing right now. This was my first teacher for fpv related content! #gonetoosoon

[@OneDon271983]

Still helping us from beyond. Cheers man

[@ForfeitKhadgar]

Subbed, your videos make this hobby so much easier when you're ballin on a budget

[@sadigov]

Another very useful tutorial. Thanks for posting!

[@OliFPV]

still help me in 2019 🍀 thx 4 all ,rip

[@yasalame3128]

Thanks for that Video ! I think it will help me a lot!

[@kumardeepam]

Thank you so much for sharing this knowledge 🌞🙏

[@jwelsh1w]

really really really helpful. Thanks man!

[@Valeriy7D0]

Thanks for great video!

[@philpelaez]

You are the man!!!!

[@snpa240]

Thanks for this! Saved my pcb

[@monivibes1]

Great tutorial!
I noticed that you utilized solder paste. I'm curious as to how the VJST pins adhered without prior tinning. Are they pre-tinned by default .

[@CrazyRandomLord]

Is it easier to solder a new connector on or to solder the wires directly onto the board? I assumed the connector would make the fine point job a lot easier but you made them sound equally as feasible.

[@jcrisen5417]

Hey great vid. I just bought an eachine wizard arf. Tried connecting my frysky ia6b receiver to the FC through the 8pin connector with the ppm cable. My receiver is not getting any power to it. I put a multimeter on the 8 pin connector and the 8th pin reads 3.24v. I don't get any volt readings on the pin that is suppose to supply power to the receiver. I connected the receiver to a separate power supply and it works. My FC powers up find and is working normally. Any idea why I can't get power to the receiver from either io2 or oi1 on the controller? Thanks

[@visualimpactart]

THANK YOU!!!!

[@peterreilly9740]

do u have one for the micro fc my motor connectors broke

[@reidbtable]

Can this procedure be performed on a broken micro usb??? If so, I can save 3 F3 Omnibus AIO that i have with the micro USB broken off.

[@reidbtable]

If you have a video or instruction for connecting my THREE F3 Omnibus FCs that have the micro USB broken off I would be eternally grateful. Cant connect by UART1 with FTDI OR Arduino nano. Really dissapointed in this board.

[@rubenm6781]

thanks blue falcon, my io pins broke on my piece of crap f3 board i was about to throw in the trash but i like the way it flys so i saved it

[@philpelaez]

Hey bro..do you have one on how to remove it ?

[@ProjectBlueFalcon]

I'll make one

[@atomicskull6405]

Picoblade is Molex not JST btw.

[@leso204]

that soldering is bad'.............