This is my favorite......sounds nasty, revs like rock star, big block power in a small block package, a real sleeper as long as you put real quiet mufflers on it...just totally nasty sounding. I love it! Also, if SS says he has a 283ci V-8 and he rates it at 600 ft lbs, it probably has 650 ft lbs...or more!! Believe it! These guys do NOT fuck around.
@@AeroSS87 Not always. But you need a bigger cam etc. for the larger cube engine to sound pissed off. Throw a cam with over 280 degrees of duration and over .850 lift in a 582 and it will sound properly pissed off too, especially if the CR is 11:1 or better. Small blocks are just that, small, and thus a small cam sound big.
Hey Chevy Block they are rocking a T&d shaft mount rocker system 1.6 ratio with PAC springs with a max lift of .800 and Afr 245 npp heads with a 70cc exhaust chamber Dart LIL M block 400 stroked to a 434 6" manley h beam rods 4inch stroke and 14:1 compression with weisco domed pistons and alot more. reason I know i did by the same motor and nitrous ported my pistons and added a 300 shot.
If you want to go fast see these guys. Ask for Vinnie a real good guy. I know of 3 motor came from them and they make unbelievable HP. And also produce numbers at the track. Can't say anything bad about them but Bad Assss
Probably 7200 or 7300. You can get SBC hydraulic setups to hit 8+ grand these days. As long as you use good lifters and proper springs, it can be done.
You obviously are not familiar with Shafiroff, nor their reputation. Their claims are accurate and every engine is dyno tuned and shipped with the dyno sheet.
Mate not need to be jumpy what’s their rep? Im been researching about them and they had quite few issues then again not one mechanic is perfect so don’t say they are
mr srb if you dont know Shafiroff's reputation, then you must not be into the drag race scene in the U.S. He started out as a drag racer and became an engine-building legend...one of the bigger shops in U.S. along with others like Reher-Morrison...
That one sounds a lot better than the non hydraulic roller cammed according to the video anyway.
This is my favorite......sounds nasty, revs like rock star, big block power in a small block package, a real sleeper as long as you put real quiet mufflers on it...just totally nasty sounding. I love it! Also, if SS says he has a 283ci V-8 and he rates it at 600 ft lbs, it probably has 650 ft lbs...or more!! Believe it! These guys do NOT fuck around.
I'm having a 434 built by them to run high 9s in my 92 street camaro 👊🏾 734 hp
Go check out the Pavtek 434 inch motor makes 750HP all day
@@TheRoguelement COPY THAT!👍🏾
Did you make 9s?
@@lewisfoltz6306 980s
@@TheRoguelementit’s only listed at 650 on their site hey?
Gotta love the big block's little brother...just rev it higher
Ia it just me or sb sounds angrier
@@Stolencamaro big blocks sound meaner, small blocks sound more pissed off
@@AeroSS87 Not always. But you need a bigger cam etc. for the larger cube engine to sound pissed off. Throw a cam with over 280 degrees of duration and over .850 lift in a 582 and it will sound properly pissed off too, especially if the CR is 11:1 or better.
Small blocks are just that, small, and thus a small cam sound big.
Hey Chevy Block they are rocking a T&d shaft mount rocker system 1.6 ratio with PAC springs with a max lift of .800 and Afr 245 npp heads with a 70cc exhaust chamber Dart LIL M block 400 stroked to a 434 6" manley h beam rods 4inch stroke and 14:1 compression with weisco domed pistons and alot more. reason I know i did by the same motor and nitrous ported my pistons and added a 300 shot.
U bought it from them? Any feedback?
If you want to go fast see these guys. Ask for Vinnie a real good guy. I know of 3 motor came from them and they make unbelievable HP. And also produce numbers at the track. Can't say anything bad about them but Bad Assss
How much does this motor cost
@@josephbutler3577 $16400 as of 7/21/20...less carb and ignition
@@josephbutler3577 Just go to their website and check. It's a crate, it's all there.
I would like to see scafiroff sell the complete exhaust system and then tune it on the dyno
Now i have to call in sick to work
Looks serious
Whats the compression
10.95/1
@@Stolencamaro nice
There's no chance this thing makes 700 horsepower with 10.9 compression
A great Engine! ;)
Is this a aftermarket block?
Dart SHP
Dammm!! Nice
30k?
Damn it sounds like they revved it to 9 grand I want to see what kind of valve train they're rockin
Probably 7200 or 7300. You can get SBC hydraulic setups to hit 8+ grand these days. As long as you use good lifters and proper springs, it can be done.
need raw proof that not really showing us alot
@D James Morgan right !
Raw proof is in the company name. Thats why you pay more and have quality.
what a joke!!! show the dyno sheet! All I saw was a noisey engine,,,
You obviously are not familiar with Shafiroff, nor their reputation. Their claims are accurate and every engine is dyno tuned and shipped with the dyno sheet.
+AeroSS87 asking to see the dyno sheet is a fair question. Info there I want to see. 700 ho is a good engine,,Lukovich also builds good engines
Mate not need to be jumpy what’s their rep? Im been researching about them and they had quite few issues then again not one mechanic is perfect so don’t say they are
mr srb if you dont know Shafiroff's reputation, then you must not be into the drag race scene in the U.S. He started out as a drag racer and became an engine-building legend...one of the bigger shops in U.S. along with others like Reher-Morrison...
Go back to your doggy Ford coyote
Thanks for telling us the build list