Это видео недоступно.
Сожалеем об этом.
Flysky FS i6 Elevons Setup, How to mix Two Servos channels of RC Plane or RC Flying Wings
HTML-код
- Опубликовано: 21 янв 2021
- Read article:
www.electronic...
RC Planes Designing and Making Videos
Arduino LoRa RC Controller, 5Km Range
• Arduino LoRa RC Contro...
Twin's Motor RC Plane Design Calculation, making, and flight test:
• RC Plane Designing Cal...
RC Paper Airplane making and Flight test
• RC Paper Airplane made...
SU27 RC Jetplane making and Flight Test:
• RC Jet Plane with 2600...
Diy Highly stable RC Plane designing and making:
• Diy RC Plane for Begin...
Amazon Purchase Links:
Best RC planes and Accessories
amzn.to/35XXpPN
Flysky FS i6 Transmitter and 6 Channel Receiver
amzn.to/363Cqez
Servo Motors
amzn.to/3c162wP
1000KV Brushless DC Motor with ESC
amzn.to/2NtHfaR
Servo Motor control horns, pushrods, etc
amzn.to/3nZ6GNW
6000mAh lipo battery, 4s
amzn.to/3c1yn6u
1000mAh lipo Battery, 3S
amzn.to/3sN9hOs
Balsa wood sheets for RC planes
amzn.to/2KAO0q1
*Please Note: These are affiliate links. I may make a commission if you buy the components through these links. I would appreciate your support in this way!
Support me on Patreon and get access to hundreds of projects:
/ electroniclinic
Project Description:
********************
In this video, you will learn how to set up Elevons for an RC plane or RC Flying Wing type design using the Flysky FS i6 Transmitter and a 6 channel Receiver.
We have two servos and a 1000KV Brushless DC motor. The Brushless motor is connected with Channel 3 and the two servos are connected with channels 1 and 2. The Servo motors are connected with the control surfaces called Elevons. The reason these control surfaces are called Elevons because they both work as Elevators for the Up and Down pitch movement and as the ailerons for the roll movement of the RC Plane. So, anyhow the transmitter is already bound to the receiver. Before you start setting up the Elevons, make sure you remove the propellers, check all your connections and then go ahead and connect your battery to power up all the electronics.
Now, turn ON your transmitter, and you can start by checking your control surfaces using the control sticks or joysticks…You can see when I move the control stick in the downward direction or in the upward direction I am only able to control the left side control surface this is because the two servos are connected with different channels… The same thing happens when I move the control stick to the left and right…Channel 3 is working fine, I can control the speed of brushless motor… The only problem is with the channel 1 and channel 2 and this is the reason the two servo motors behaves in an abnormal way. This is what we are going to fix now.
********************
Amazon Purchase links of other components and tools if you need:
*****************
Arduino Uno, Nano, Mega, Micro "All types of Arduino Boards":
amzn.to/3fk5OTi
Top Arduino Sensors:
amzn.to/3vZbnfM
Super Starter kit for Beginners
amzn.to/3cq56C5
Top Oscilloscopes
amzn.to/3ctF3d8
Variable Supply:
amzn.to/2PEAqE7
Digital Multimeter:
amzn.to/2QGRPg1
Top Soldering iron kits: "best"
amzn.to/39nqDtb
Top Portable drill machines:
amzn.to/3suQMh7
Jumper Wires:
amzn.to/2NYPEDA
3D printers:
amzn.to/3ruG1dt
CNC Machines:
amzn.to/3cuZWVv
Electronics Accessories:
amzn.to/3sueV7z
Hardware Tools:
amzn.to/3m9UhaN
DISCLAIMER: This video and description contain affiliate links, which means that if you click on one of the product links, I will receive a small commission. This helps support the channel and allows me to continue to make videos like this. Thank you for your support!
****************
Follow me on Facebook:
/ electronic-clinic-7697...
Follow me on Instagram:
/ electroniclinic
Email:
stu_engineering@yahoo.com
About the Electronic Clinic:
Electronic Clinic is the only channel on RUclips that covers all the engineering fields. Electronic Clinic helps the students and other professionals to learn electronics designing and programming. Electronic Clinic has tutorials on
Arduino
Raspberry PI
image processing
gsm based projects
Bluetooth based projects
esp8266 projects
Nodemcu projects
robotics
desktop application designing and programming
Project Related Tags:
flysky transmitter and receiver
flysky fs i6 elevons setup
flysky fs i6 ailerons setup
flysky fs i6 two servos channels mixing
how to mix two channels using flysky fs i6
flysky fs i6 rc plane elevons setup
flysky fs i6 rc plane ailerons setup
flysky fs i6 rc plane main menu
flysky fs i6 rc plane settings
flysky fs i6 rc plane pitch movement
flysky fs i6 rc plane elevons and ailerons
flysky fs i6 rc plane flying wing design
Sending a thanks to a newcomer to the rc world in 2024.
You are a lifesaver, man! I'm totally new to rc planes and I'm trying to set up a flying wing like yours and this is the first video I've found that actually addresses this set up.
check my other videos on rc planes designing and quadcopter.
life saver, i totaly lost hope that my 6 channel reciever i not gonna work for my diy, but you gave the wisdom on how to configure it....thx 😂😂😂😂
Thank u so much I was literly crying because I couldn't find out what was wrong
I’m the same as you all!, helped me out allot as I was trying to get my right Joy stick to move my rudder on my sail boat, it was operating fine up and down but not left to right🥴 but because of this video I was able to change it.😁😁😁
Very helpful and thorough video. You’ve given me a better understanding of these devices than any other I’ve sourced before.
man...i was totally lost ..thank you for this video it was exactly what i needed
I am so thank you for your video. Last night try to solve this issue but I coulnd’t. Thank you for sharing.
My friend, you saved me. I thought my money was wasted!!!
Thanks now i have a confidence to continue with a custom v tail design plane. why does nobody love the v-tails
Thank you very informative.
Check the propeller,the curve part facing forward and the concave curve facing rear.
This is in pusher models
thank you so much for this, ive been trying to figure this out for the past couple days an i didnt really know what to search for to find the solution an finally stumbled onto this video. my plan is nothing like this. but i plan to make one similar soon. but i was having trouble trying to get my ailerons working from 2 servos on while controlling both of them so i think this will help take care of if, or at least it will send me on the right track in figuring it out
good man, straight forward solution.
Thanks man
Thanks for the help😊
Brilliant thank you.Simply explained.. I understood it completely ✈💯
Thanks very much for your help!"
i would like to thank you for this video your the only one that solved my problem!no one eles sai d put in 1 and two i thought put spliter on one. thanks!
Thanks
Hello thanks. But could you help me because I have an old Futaba attack 4 in 72 Megaherz am and also the channels and receptors. So how can i do with some circuit to do this mix for elevon in my flying wheel if the radio does not have this option. Only reverse servos.....any idea? Apart of buying new 2'4 ghz digital radio and receptor😅
Can you make s tutorial on how to do this on mc6c transmitter
Fiz aza zag do v911, mas não consigo ajustar aileron e profundor. Como faz?
bro pls make a video of Elevons Setup and How to mix Two Servos channels of RC Plane using flysky fs ct6b transmitter pls
what do you do if the elevator part is working in reveres?
Thank you brother !
Thank you Sir, great video!
Can I arm FPV using flysky i4x 4 channel transmitter
is it me or the aileron controls also needed to be reversed at 4:34 ?
I thought exactly the same thing. In that case it can be rectified by swapping the two aileron servos plugs in the receiver.
Thank you man
What’s the Difference between Elevon and Mix?
interesting airplane
thanks bro I just finished making my flying wing
It can be mixed channel 3 to 1 and 2?
Awesome thanks for the tip, do you know if I can use a FlySky i6S for this? My radio is a little different
Hello, I need mine to do the reverse thing when I move the stick side to side but need a different chanel for the up and down movement, how do I do that?
You wing is turning opposite of the direction that your pushing your stick
👍🏼👍🏼Thanks
How did you connect the servo motors to operate simultaneously and inverse and with how many channels.. I want to know the circuit, I use FS-CT6B Remote Control. Please guide me with the above issue.
Woow excellent
thanks. and how do I build the servos?
Wow Great Video Bro 💥💥
Hey!can we use the elevator,aileron button to control servo if we make a drone and attach servo motors to Receiver?
Bro please reply iam in need of it
How to make the alieron and elevator mix ? For example when I turn left and right with the alieron I want the elavtor to move up aswell . instead when I turn to one side the elevator goes down and when I turn to the other side it goes up . how to make the elevator stay up when I turn both sides?
im not to sure but i think that would have something to do with mixes i would try to look into mixes on this remote might help lead you down the right path
Its very halpfull for mo
Ser plese make the video on fsi6s
ARE YOU DONE? THE ALERONS ARE NOT MOVING THE RIGHT WAY.
i am new to this my first time i really don't no what to do i only follow ur video and do it just that wing don't work and tail don't work also they don't move at all
Plz share their Flight result video.
very soon i will upload the video.
Ok
Hi how much voltage is that battery Pls tell ❤️
that's 3s, 11.1volts
@@ElectroniClinic sure will it support it I'm not sure I'm going to buy one of the same reciver but idk what voltage it could hold I asked on e of the seller he said that it could hold 4-7v I'm confused bro 🤔
@@dorigami4819 are you asking about the lipo battery or the transmitters batteries?
wow what a explanation
Your ailerons are still reversed
No the plain is upsidedown
my wing dont work for some reason
did you check your servos ?
how the control surfaces respond to your commands?
but some how ESC Work