Steel wool is sold by different degrees of courseness. 0000 is the finest grade. I suspect your local hardware store sells small packages of steel wool. You’ll see 0 grade, 00 grade etc..
Would this work with a rubberwood butcher block tabletop? If working with an already stained piece that needs to be stripped, would you use the angle grinder first or the stripper?
That barnwood has become quite expensive .. any barns that are in danger of falling down in my area, well .. the Amish usually try to get their paws on it to salvage and sell the wood. Thanks for sharing your ideas.
I like your technique for distressing the wood but I found using a solution of white vinegar, cheap dollar store fine steel wool, tea bags and instant coffee to not only be very cheap but very good way to instantly age the wood. Colors will depend on the type of wood and amount of existing tannins. When done looks very old.
@@AlleyPicked I use a gallon of vinegar and dissolve a package if fine steel wool in it for 3 days. I then add 6 teabags and 1/4 cup of instant coffee dissolved in 1 cup of hot water. Let sit over night. Just paint on bare wood with a brush. Don't worry about the excess because it will drip off. Within 5 minutes the wood will darker and continue to do so until dry. Will look like barn wood thr next at. May darken a bit over the next couple of days. Note results will vary depending on type of wood.
@@fredstratton2841 Wow - I wonder which Chemist came up with that idea. I vaguely remember hearing about the steel wool trick before. I will definitely give it a try. If it's good, I think I'll use it in a video. I was not extremely impressed with the stain method I used in my video. Thanks for the detailed recipe.
I have seen a few comments about using vinegar and steel wool. In my opinion, that technique gives the wood a more natural weathered look with a lot less work.
The mantle should not get hot enough to require a special heat sealant. In fact, I don't know if there even is such a thing. There is heat resistant paint for metal but no wood finish that I know of.
Thanks for sharing this video. I will be building a vanity for our bath and I want it to look old. I’ve perfected the concrete countertop and this will look super rustic with your technique. How’s this work on oak?
Without a lot of details, the general answer is yes. Wood outdoor if not sealed will eventually deteriorate. The green treated lumber would be better to use but even that stuff should eventually be treated (after it dries) or an outdoor stain/sealer applied.
It wasn't really "hairy". Slightly I guess, but after staining, it's surprisingly smoother that you would think. You can experiment using a finer abrasive wheel and different stains and paints. Part of the fun is experimenting for yourself.
I don't believe I sanded it at all after the wire wheel. If after using it you want a little smoother texture, you certainly can sand it. Perhaps with an 80 grit but that may not be necessary at all.
I barely used the grey and it seemed to overshadow the coloring too much; whereas, you completely covered the board. Did you thin the grey first, or did you redo the board during editing. I even tried to make a second pass with the kona after the grey....still didn't care for it. Your final product seemed to have a very thin sheen which accented nicely.
I did make that video a while ago so I don't remember exactly. After applying the gray, I would put some paint thinner on a rag and wipe down the wood to remove some of the gray. I may have don't that myself. Just can't remember. Give that a try.
Somehow, I missed this gem when you first posted it, Tom. I'll try to watch more closely in the future for your video posts. You are definitely the Vincent van Gogh of estate sales and recycled lumber (even if it is genuine, faked recycled lumber). BTW: I don't like that aging stain, either.
Great video and explanation. LOVE the Tim Taylor sound effect. 😂
You are funny, creative, and resourceful! Great delivery and humorous bits.
WOW!!!!! I have seen a can of Hills Brothers Coffee like that since the 60s back in NYC and Long Island.......oh....the video was great too!
Thanks for watching!
I love the honest feedback about the first stain! I laughed so hard--then I hit subscribe!
BTW I really enjoy the format (character) of your videos. Very entertaining.
Thank you for the kind feedback.
This was a really cool video cheers mate
I really really like this...and you !!
You can get that gray patina using white vinegar. Put 0000 steel wool in jar with vinegar. Wait 24 hrs. Brush on. Let dry and the wood is aged.
What is 0000 steel wool
Steel wool is sold by different degrees of courseness. 0000 is the finest grade. I suspect your local hardware store sells small packages of steel wool. You’ll see 0 grade, 00 grade etc..
Would this work with a rubberwood butcher block tabletop? If working with an already stained piece that needs to be stripped, would you use the angle grinder first or the stripper?
Great job mate and always entertaining. Thanks for all the effort you put into your vids - I appreciate it.
"Curl up with your ...angle grinder"
👍 and subbed.
❤️🇨🇦☕️☕️
That barnwood has become quite expensive .. any barns that are in danger of falling down in my area, well .. the Amish usually try to get their paws on it to salvage and sell the wood. Thanks for sharing your ideas.
A way cheaper and more authentic way to weather the wood is the steel wool/vinegar method. Cool technique on the grinder.
I like your technique for distressing the wood but I found using a solution of white vinegar, cheap dollar store fine steel wool, tea bags and instant coffee to not only be very cheap but very good way to instantly age the wood. Colors will depend on the type of wood and amount of existing tannins. When done looks very old.
I will have to give that a try. Thanks for the tip. If it works, I might just have to use it in a video.👍
Just mix the 3 ingredients together I assume?
@@AlleyPicked I use a gallon of vinegar and dissolve a package if fine steel wool in it for 3 days. I then add 6 teabags and 1/4 cup of instant coffee dissolved in 1 cup of hot water. Let sit over night. Just paint on bare wood with a brush. Don't worry about the excess because it will drip off. Within 5 minutes the wood will darker and continue to do so until dry. Will look like barn wood thr next at. May darken a bit over the next couple of days. Note results will vary depending on type of wood.
@@maxglitz the tea helps on wood like pine and spruce which do not have much tannins. The coffee adds a deeper color but is not necessary.
@@fredstratton2841 Wow - I wonder which Chemist came up with that idea. I vaguely remember hearing about the steel wool trick before. I will definitely give it a try. If it's good, I think I'll use it in a video. I was not extremely impressed with the stain method I used in my video. Thanks for the detailed recipe.
Nice job - some handy tips and great video. Thanks 👍
funny and really good content! thx
Glad you enjoyed!
I have seen a few comments about using vinegar and steel wool. In my opinion, that technique gives the wood a more natural weathered look with a lot less work.
I have done that too in another video. It's good to have options. Both methods can also be combined.
subscribed! great channel!
Thanks!
Quick question. I threw away my weathered grey stain as per your instructions. What do I do in the final step now?
Your turned out perfect , we’ll see how mine ends up, Thank you so much for sharing. Happy holidays👍😊🎄🎄
Thanks! I think next time I will experiment with some white wash or chalk paint on the outside. Happy Holidays :-)
could you use this technique to make a mantle over the fire ??
Absolutely!
@@AlleyPicked Thank you! Would you need to put a heat resistant sealant or anything on it ?
The mantle should not get hot enough to require a special heat sealant. In fact, I don't know if there even is such a thing. There is heat resistant paint for metal but no wood finish that I know of.
Thanks for sharing this video. I will be building a vanity for our bath and I want it to look old. I’ve perfected the concrete countertop and this will look super rustic with your technique. How’s this work on oak?
I have not tried oak but I bet it will work great. Oak has lots of grain in it which is what will stand out.
killer video! subscribed! thank you :)
Very cool! I’m going to try it. Thanks
I don’t have an angle grinder. Can I use a drill instead? Are you using a knotted wire wheel or a wire brush wheel? Please help me. I’m new to this.
I drill might also work. I have not used a drill before for this but you can always try it. It couldn't hurt.
What do you think of the steel wool and vinger trick
Not bad. I made a video about it if you are interested. ruclips.net/video/m6U3JFSacRE/видео.html
I want to do this on a shed I'm building. Since the stain will be exterior, do I need to seal it?
Without a lot of details, the general answer is yes. Wood outdoor if not sealed will eventually deteriorate. The green treated lumber would be better to use but even that stuff should eventually be treated (after it dries) or an outdoor stain/sealer applied.
Doesn't the wire cup leave the wood kinda hairy? Do you ever follow it with maybe a finer wire wheel or abrasive wheel? Thanks.
It wasn't really "hairy". Slightly I guess, but after staining, it's surprisingly smoother that you would think. You can experiment using a finer abrasive wheel and different stains and paints. Part of the fun is experimenting for yourself.
What kind of wood are you using in this video?
In this video I am using pine. I have also used oak and that works good as well.
Great video. 3 thumbs up! 👍👍👍
So, if you make cool stuff out of junk, how come you didn't use the Varathane? ;)
Did you sand the wood before staining? If so, what grit did you use?
I don't believe I sanded it at all after the wire wheel. If after using it you want a little smoother texture, you certainly can sand it. Perhaps with an 80 grit but that may not be necessary at all.
I'm glad I clicked on this video
Random ? By any chance do you live in Chicago
Grew up there. Live very close now.
@@AlleyPicked yeah I kind of figured because I live in Chicago and I know the way the AlLeys look.
Keep up the GREAT WORK.
@@geogonzalez3586 Good observation 🙂
Tim the tool man!! 😆
One of my favorite classic TV shows :-)
Very cool technique. So that's where my awl disappeared to.
I barely used the grey and it seemed to overshadow the coloring too much; whereas, you completely covered the board. Did you thin the grey first, or did you redo the board during editing. I even tried to make a second pass with the kona after the grey....still didn't care for it. Your final product seemed to have a very thin sheen which accented nicely.
I did make that video a while ago so I don't remember exactly. After applying the gray, I would put some paint thinner on a rag and wipe down the wood to remove some of the gray. I may have don't that myself. Just can't remember. Give that a try.
@@AlleyPicked Thank you!
Hi, are those stains water based?
I used oils based stains for this project.
@@AlleyPicked ok I think I need to thin mine down, the grey is really thick. What's the best thing to thin it down with,?
paint thinner or mineral spirits
@@AlleyPicked ok I'll have to get some, all I have is acetone. Thanks so much
Couldn’t I just go to the Gaines’ Magnolia place and buy some of that shiplap stuff they’re always using?
Somehow, I missed this gem when you first posted it, Tom. I'll try to watch more closely in the future for your video posts.
You are definitely the Vincent van Gogh of estate sales and recycled lumber (even if it is genuine, faked recycled lumber).
BTW: I don't like that aging stain, either.
Interesting
and tuck in your shirt when using the angle grinder!!
Yes mother :-)
@@AlleyPicked i had a wire wheel catch my left nipple… because of my untucked shirt.
yes $8 a square foot is pricey even when it’s not my money
About $60 now...
You shouldn't throw paint in the garbage
too gray
👍👌
The part about the accelerator 😂😂😂😂😂😂couldn’t of said it better myself - absolute junk!!!