The air which remove from the cooling coil is cold and if we connect the cwrl the that air become hot. Hence reduces efficiency of Ahu. However we connect cwsl.
Cooing coil circulting supplying up and bolwinging distbuting room cool heating retanning line outgo $$$explas shell and tubes are fitted in side the steel shell copper tubes as shown in the diagram . Cold water is circulated through the tubes by a watwr circulating pump The high pressure vapourcoming outofthe
Cold water culating throughthe tubesandthe vapour changesto liquied.thecollected at the bottom ofther condenser passtothe passed direactly tothe evaportor The hot waterfromthe tubes thus passtothe coolin towerand coold the coldwaterfrom the cooling tower is again circulated through the conder by water pump This continued when the water continuously circulaters rhhrough the tubes the inside becmoes coated wuth scaleand orher materials in water .. dis tey buing supppling
Chilled water is supplied from bottom so that the coil runs full of water, it will advace slowly filling the pipe completely....if we supply it from top, water will rush through the coil downwards and the water may not have full contact with the pipe surface leading to lesser heat exchange.
Pressure gauge ke thirmovell me Glisreane liquivid dalte hai, normal tempreture ki jagah. Ager zyada tempreutre hai to selicon liquivid dalte hai. Ye pressure ki wajah se huwe vibration ko control karta hai jisse accurate reading le ja sake. Sath hi ye gauge ke parts aur dial ko bhi kharab hone se bachata hai.
Nice, very helpful. Upload more videos on HVAC piping system please like for Pumps - vertical & horizontal, chiller, boiler pipe connections. Thank you.
Warm water rises due to its lower density compared to cooler water. By placing the supply pipe at the bottom, the warm water enters the coil and naturally rises as it absorbs heat from the air passing over the coil This rising motion helps maintain a consistent temperature gradient, enhancing the heat exchange process
Ahu ke bottom se child water suply hum isliye conect krte hai heat transfer jo ho wo better tarike se heat transfer ho dusra child water suply ata hai child water se air me heat transfer ho jab hamara child water ata hai to wo cooling coil se feel hote hue ata hai isliye niche se child water suply ko conect krte hai agar hum upar se conect krege to wo crevety se child water direct niche aa jyega Or wo cooling coil ki contect me jyda der nhi rah payega isliye niche se child water suply line ko niche se conect krte hai
The CHWS always be connected to the bottom side of AHU because we have to filled the pipe lines maximum by the chilled water and there is no air vapor existing during the CHW circulating. also its helps to make a proper cooling due water resist to up side and absorbed to all heats.
Sorry for delay friend.....CFM ka video bhut jald upload ho jayega...or AHU k blower ka video v koshish krunga dalne ki... Channel se jude rhe or v informative videos ayegi
@@HVACWorld sir as you said above that if we are using PICV then no need to install DRV but i saw in other channels they use both Valve at AHU connection so i got confused please clear this one we should use both valves or not as per international standards
Chilled water pipe connect from bottom because it takes time to return due to time delay the cooling efficiency is good. if we connect from top it passed very fast because of this cooling will be affected.
AHU Chill water pipe line ke saat Hot water pipe line be Hoti hai jiska temperature 55 degree Celsius hota hai usske bare me koyi information hai Tu please bataye ....ussi AHu me Kay working role hota hai
@@HVACWorld sir usne chilled water line ke supply nd return ka pressure pucha h ? Pls tell me I also want to know I have seen in psi Supply line pressure 100 psi Nd return line pressure 90 psi which means 10 psi difference I don't know in kg/cm^2
Because that will cooling effect in the room go and check temperature thermometer and pressure gauge of ahu..the supply of water down temperature show thwn you will have to check satiner and clean cylindrical filter and fix again
Water always coming from bottom, bcz if water is passing from cooling coils from bottom to up it will take time bcz of gravity and it get cooled bcz of gravity force concept.
Chilled water pipe neeche isliye hoti hai kyuki, chilled water me moisture ( more weight) and return water pipe ka weight kam hota hai. ( less moisture ) , isliye water ka circulation ache se ho. Please reply I'm right or wrong.. I'm new, (fresher) .
Why do we connect CHWS pipe line in bottom of the cooling coil and CHWR pipe line in top of the cooling coil.. comment your answers
CHWR has warmer water than CHWS, as warmer water has lower density it will be easily go up so load on pump will automatically reduces
The air which remove from the cooling coil is cold and if we connect the cwrl the that air become hot. Hence reduces efficiency of Ahu. However we connect cwsl.
Because of gravity
Cooing coil circulting supplying up and bolwinging distbuting room cool heating retanning line outgo $$$explas shell and tubes are fitted in side the steel shell copper tubes as shown in the diagram . Cold water is circulated through the tubes by a watwr circulating pump The high pressure vapourcoming outofthe
Cold water culating throughthe tubesandthe vapour changesto liquied.thecollected at the bottom ofther condenser passtothe passed direactly tothe evaportor The hot waterfromthe tubes thus passtothe coolin towerand coold the coldwaterfrom the cooling tower is again circulated through the conder by water pump This continued when the water continuously circulaters rhhrough the tubes the inside becmoes coated wuth scaleand orher materials in water .. dis tey buing supppling
Achha lga hai Sir aapka video ..
Ummed krte hai aap aise hum knowledge dete rahenge taaki hum jaise new chiller tech v ek achhi job pa sake
Chilled water is supplied from bottom so that the coil runs full of water, it will advace slowly filling the pipe completely....if we supply it from top, water will rush through the coil downwards and the water may not have full contact with the pipe surface leading to lesser heat exchange.
100 % correct.....
sahi hai bhanjee 🔥🎉
Sir bohat badiya ...please vedio banate raho sir please
Superrrr superb knowledge full video bro.
Thanks 👍🏻👍🏻👍🏻
Ok bahut badhiya samjhae Hain aapane
very well explained process and description of each items used.
Pressure gauge ke thirmovell me Glisreane liquivid dalte hai, normal tempreture ki jagah. Ager zyada tempreutre hai to selicon liquivid dalte hai. Ye pressure ki wajah se huwe vibration ko control karta hai jisse accurate reading le ja sake. Sath hi ye gauge ke parts aur dial ko bhi kharab hone se bachata hai.
Nice explain❤
Nice information sir
Very good explain sir
Ahu unit ke supply line me drain cock kya kaam hota hai
Very informative video
Thanks
Nice, very helpful. Upload more videos on HVAC piping system please like for Pumps - vertical & horizontal, chiller, boiler pipe connections. Thank you.
Thanks
Very well explained process
Excellent explation thank you sir
Vrey good exlant noy belved baiwhat is sayed bai
Very good information sir ji ❤
Good information
Good
Warm water rises due to its lower density compared to cooler water. By placing the supply pipe at the bottom, the warm water enters the coil and naturally rises as it absorbs heat from the air passing over the coil
This rising motion helps maintain a consistent temperature gradient, enhancing the heat exchange process
Ahu ke bottom se child water suply hum isliye conect krte hai heat transfer jo ho wo better tarike se heat transfer ho dusra child water suply ata hai child water se air me heat transfer ho jab hamara child water ata hai to wo cooling coil se feel hote hue ata hai isliye niche se child water suply ko conect krte hai agar hum upar se conect krege to wo crevety se child water direct niche aa jyega Or wo cooling coil ki contect me jyda der nhi rah payega isliye niche se child water suply line ko niche se conect krte hai
Correct
Nice vidios 🤟👌
Very good teaching sir
Why balancing valve place at return line of AHU, why not at Supply line?
Please give me the answer.
To ensure the amount of water flow across the coil
You explained very well
Ahu pressure gauge me inlet jiyada hoga ya outlet
very good explanation sir
Excellent 👌👍
Very nice sir, pls tell me about Ahu blower working
Nice explain
Very good.
The CHWS always be connected to the bottom side of AHU because we have to filled the pipe lines maximum by the chilled water and there is no air vapor existing during the CHW circulating. also its helps to make a proper cooling due water resist to up side and absorbed to all heats.
One of the greatest answer i received....
Sir ahu ka cfm ka 2nd videos ni aya and sir ahu k blower k barr mai videos bnae .backward and forward blower kya hota hai or kaise work krta hai plz
Sorry for delay friend.....CFM ka video bhut jald upload ho jayega...or AHU k blower ka video v koshish krunga dalne ki... Channel se jude rhe or v informative videos ayegi
Kkk i m waiting for your important videos🤔🤔🤔🤔🤔
Bahut pasand aayi bhai
Sir please tell me why secondary pipe line and primary pipe line between provided bypass valve
If Balancing Valve will balance the flow, then why we incorporate PICV?
Why 3 way control valve is not shown?
if we are using PICV VALVE .. what is the need of balancing valve then ? please clarify for this point that i have raised ..
If you are using PICV valve at AHU connection, You don't need balancing valve. PICV valve self balanced water flow and regulate flow like 2-way valve
@@HVACWorld ok thanks
@@HVACWorld sir as you said above that if we are using PICV then no need to install DRV but i saw in other channels they use both Valve at AHU connection so i got confused please clear this one we should use both valves or not as per international standards
Can we place balacing valve at supply water line ?? Any drawback comparing to placing at return line ?
Awsm trick boss
Great
Chilled water pipe connect from bottom because it takes time to return due to time delay the cooling efficiency is good. if we connect from top it passed very fast because of this cooling will be affected.
Air cooled chiller me bypass line kyun use karte hai?
What should be the maximum and maximum flow in picv
Best parts use
Very well explained, but I have a doubt for isolation valve, please could you explain me the working of isolation valve ??
function is close to make maintenence, or change any device
Nicely explained
AHU Chill water pipe line ke saat Hot water pipe line be Hoti hai jiska temperature 55 degree Celsius hota hai usske bare me koyi information hai Tu please bataye ....ussi AHu me Kay working role hota hai
You will get answers to your every question... kindly get the channel membership
Good sir G
Sir pid valve open karenge to kaise maloom hoga ki valve open ho gya hai kyoki usper koi indecater ya symbol wha hota nhi hai
Inlet and outlets pressure differences???
Sir....pressure gauge me kitna pressure maintain karna hoga in aur out pipes me
Difference 0.5-1.0 Kg/cm2 ka hona chahiye
Supply 50 retand55
@@HVACWorld sir usne chilled water line ke supply nd return ka pressure pucha h ? Pls tell me
I also want to know
I have seen in psi
Supply line pressure 100 psi
Nd return line pressure 90 psi which means 10 psi difference
I don't know in kg/cm^2
@@moonsheikh7117 as per ur values, pressure difference is 10psi, i.e. 0.7 bar (or kg/cm2) which is matching with values given by hvac world
Supply and return line ka pressure defined nhi hota h.... you will get pressure difference always in TDS
Awesome
Which liquid is preferred in thermowell
Mercury is ideal
Manoj Baghel present sir
How will be rectify that strainer is dirty...
By cleaning strainer....first open tha strainer remove the mesh clean it properly and re-fix it
Because that will cooling effect in the room go and check temperature thermometer and pressure gauge of ahu..the supply of water down temperature show thwn you will have to check satiner and clean cylindrical filter and fix again
chill water piping sply yepsu ke niche rahta h jisese maintenance me aaram rahta h
Nice video
But I see arrangement with gate valve instead of butterfly valve
Gate valve is also an isolation valve....now butterfly valve widely used in ahu for pipe size 50mm and above
HVAC World right sir and thank you
My pleasure....new video also uploaded on cooling tower...watch for your knowledge and don't forget to share with friends
HVAC World sure
How much we take average distance between fitting accessories in chws or chwr?
Heat exchanger accha hone ke liye suplay in me hoti he
sir Chiller ka inlet outlet pressure kitna hona chahiye minimum and maximum
Coming video me clear kr dunga...
@@HVACWorld Thank you sir
Chiller ka inlet 7 outlet 12 hota hai
@@aymankhan9001 He is taking about pressure, not temperature.
@@sbhosale2101 oo sorry by mistake I write down temperature....
Water always coming from bottom, bcz if water is passing from cooling coils from bottom to up it will take time bcz of gravity and it get cooled bcz of gravity force concept.
Please do one more video on 3 way valve sytem
Pressure drop propeller nhi hoga or AHU k inlet nicha is liya hota hai water flow m Kuch time laga to cooling properly ho ga isliya krte hai nicha se
Very good 👍
Why purge valve place child water line and why not place on child water supply line
Air moves in updirection.. May be that's the reason
👍👍👍
Sir, reverse and forward movement aur uske application k bare me video bnaye
Reverse and forward movement of which part????...plz explain
@@HVACWorld Sir, I want dwtailed explanation of forward and reverse movement of blower as per the requirements and its appliction
@@mdashrafali7368 ok i will explained it in next video which will be upload soon
Sir can you plz 🙏give me your contact no. Jiske dwara me apse call par dowt clear kar saku
Sir plz don't ignor me
Me mechanical engineer hu me pharma company me job karta h
Inlet hamesha niche iss liye hota h q ki air lock se bachne ke liye hota h
ok 3way velbaka sath ek video
Ok
Requesting an English language.
Bahi Y stanar retain line rahta sayad
Nahi supply me hota hai
Sir how to set balancing valve
Chilled water pipe neeche isliye hoti hai kyuki, chilled water me moisture ( more weight) and return water pipe ka weight kam hota hai. ( less moisture ) , isliye water ka circulation ache se ho.
Please reply I'm right or wrong..
I'm new, (fresher) .
I appreciate your effort....iske answer ka maine separate video bnaya hai...aap wo dekhe, apka doubt clear ho jayega....
Is there English explanation .
IAQ ( INDOOR AIR QUILET) AHU STATEME KE BARE MEIN VIDEO BANAYE
Sir tho definition written mai bhi daliye
Ok sir g
Water ka pressure drop hone ke liye
Vai kichlia niche araho?
Sir
Chiled Water pipe Noxhe Se Q connect Rehta Hai
Kyu k paani upar ayega to gravity k against me ayega jisse ke ye ensure hota h k coil k andr pura paani fill ho or better heat transfer ho
Mohit sharma
Roll no 17
Plz
Not in English why??
This connection not gives satisfactory result.Only 3 way motorise valve give proper result.
If Balancing Valve will balance the flow, then why we incorporate PICV?
My Questions also same to u We r using PICV then why required Balancing valve