Это видео недоступно.
Сожалеем об этом.
how to ZERO GAP Oster Fast Feeds (Simple in-depth STEP BY STEP)
HTML-код
- Опубликовано: 21 июн 2015
- Follow me on Instagram @anguswannnn
This is how to properly zero gap Oster Fast Feeds without switching the blade with a detachable blade
Your method is perfect. My Fast Feeds are now zero gapped, and without any issues. Thanks for posting!
Perfectly executed zero gap. Great attention to detail in the video. Clear and precise!
thanks dude, made a quick notch with the dremel. Worked like a charm
This was some very good information! Great video!
Just had to do this when my andis ceramic blade had a slight high point in the middle of the blade. Now I’m just using the stock blade with this mod, thanks bro. 👍
A1 video Bruh, thank you. I uses this procedure twice. Both of my fast feeds are hitters!!!
Out of all the videos I watched to perform this zero gap operation, this was by far the best! Please consider doing a video to replace the metal moving cutter blade with a ceramic blade.
I tried it and for my first attempt I got it thanks for the video tutorial
Thanks man worked !!
that is perfect great video
thank you dog resulted perfectly salutos from lisbon portugal
Very good i dont used yet but i know is work!
Cool....I needed that.....Thanks....
Un saludo desde Argentina me sirvió muchas gracias la verdad un cracjs
dope. will be doing this.
Time to use all the metal blades I’ve been swapping out for people over the years 🥴🤘🏽
Very informative and detailed video! You're the best
dope how did I not see this vid
Very smart bro. Nice mod!! Now I don't have to buy the speed lines lol. What would you rate the 0? 000-000000
What if the screws that hold the metal piece is stuck and won't come off
Thnx bro
Very nice
For any viewers in the future.. just buy a classic 76 #1 blade and it’s perfect.. and you don’t have to cut pieces in your clipper.
Nice
Just did this and when i open the blade the blade is too tight and doesnt work not sure why
What would happened if the two screws holding the metal plate that you cut got loose from usages? Would the metal plate move up with the cutting blade and cut you?
kyanledesign it'd be pretty bad if they went loose but they haven't for me and it's been almost 2 years! Just make sure you really tighten the screws.
Put some lock tight on the thread of the screws before you tighten them to have it even less likely that the screws will become lose
What does the zero gap do ? Does it shave closer ,I have an oster Topaz ,bought new blade but doesn't shave close
Are they buzzing loud?
Better way is to use some good round gun files and just file back the screw holes instead of cutting the backs out.
Can you use this methods with a ceramic blade? It's longer than the standard blade.
I believe you wouldn't have to do this if you get the ceramic blade, it'll be long enough to zero gap it from what I've seen in other videos
I should have done this instead of getting the Andis ceramic blade. The andis blade is wider and you will not be able to use your oster guards. The blade will hit the guards making them loud and unable to cut as good. No one tells you this in all the zero gap videos. Fast feeds with the andis ceramic blade is good if you plan to just use it to fade and not use any guards.
If you zero gap with an Andis Course Ceramic Blade, you should pick up a set of Andis Master DUAL Magnetic Comb Set. They are better comb set, in my opinion. Just make sure they are the purple, DUAL magnet jawns. Andis does also sell purple, SINGLE magnet combs. I have zero gapped Oster Fast Feeds both ways and both ways work great, it comes down to preference.
Does it decrease the opening of the blade?
Calebe Roschild nope, works just the same as if you didn’t modify it!
Why doesn’t my lever work anymore
What is zero gap?
👍🏽
Why not loosen the screws and slide the blade like every other clipper?
Because it doesn't work
Because the screw holes 🕳️ stop you 🛑
Just buy a ceramic bottom blade. It takes less than 5 minutes to do, you can potentially mess your blades up with this mod.
Matthew Richardson So you think just adding the Ceramic blade is enough. So have you done this?
Deon 0026 He’s saying, you DON’T need to do this. Just buy a ceramic blade. Then, there is no need to do all the stuff you just watched in the video. Good luck though.
What ceramic blade? I purchased one (barger) and they don’t stay in place.
@@jivorykeys www.amazon.com/dp/B07RHDH7X1/ref=sspa_dk_detail_0?psc=1&pd_rd_i=B07RHDH7X1&pd_rd_w=eN4q8&pf_rd_p=45a72588-80f7-4414-9851-786f6c16d42b&pd_rd_wg=g06Cl&pf_rd_r=1NYR0BC3P2K41X8WSM4P&pd_rd_r=a15022ea-8f06-4f0c-969c-3d511ff1de6b&spLa=ZW5jcnlwdGVkUXVhbGlmaWVyPUEzNkdDMkpLRUxFS1E5JmVuY3J5cHRlZElkPUEwODE5NDM0MVdROUJQWlM0VVo5ViZlbmNyeXB0ZWRBZElkPUEwNjg2OTc1MjNOTDhHWkxZWUdEQiZ3aWRnZXROYW1lPXNwX2RldGFpbCZhY3Rpb249Y2xpY2tSZWRpcmVjdCZkb05vdExvZ0NsaWNrPXRydWU=
I have just did the blade and it works exactly the same
Wow so you mean to tell me that we idiots been buying ceremic blades all this time for nothing????
mario figueroa hahaha. Ceramic can help zero gapped wo moding and help the blade stay cooler and sharp longer.. Other than that nothing else.
It saves you the labor of doing the mod and in my opinion the blends come out much more smoother with the ceramic, especially with the Andis Medium Cutter blade
What is the part you removed at 1:38?
Its called a blade glide
Sub!
At 1:38 what part is that called?
I lost my piece also, you find out yet?
@@nuamelo3180 It's a blade guide.
The Oster Fast Feed has been around forever. It's hard to believe that Oster doesn't sell a piece that is already channeled and relies on the user to fabricate it themselves. Don't get me wrong. I appreciate the tutorial video but Oster Inc. has to do a better job here.
They do, this tutorial is a huge waste. Just use a number 1 blade from a classic 76.