visting my elderly mom, she thought it was her remote batteries...your video saved me over $200 and without your video, i wouldng have know what to do to fix this. your going through the flashing of the lights, i never would have been able to read them, and you made it possible to show me it was the vacation switch! thank you so much!
I tried to use a Genie remote and a Chamberlain universal remote. Both would not work properly. I had to use a Linear remote to finally get it to program. Not Lowe's and Home Depot do not sell Linear remotes. What a journey.
Thank you for this video. You helped me figure out vacation mode (4 blinks) which is why my new clicker wouldn't program. I pushed the wall switch up as you instructed and the clicker then programmed on the first try.
We had the exact model, we had a power outage, and something is off. The clickers are only working in a close range, like 2 feet. I changed the batteries in them and reconnected them with the unit. Any suggestion what's wrong? I even changed the light bulb, and it's the one that doesn't interfere with the range. I played around with the antenna as well... nothing change. Any suggestion??
I’ve got the same lift motors as in your video. Have you ever had a motor go out? My door raises and closes with just a finger. With the door detached from the drive chain, the motor has trouble running just the chain. Can the motor be lubricated? The unit is a little over 2 years old. Any help would be greatly appreciated. Thank you.
I wonder if you could help , we think the torque spring needs to be adjusted tighter . The garage door opens a little less than half way . This happened after a power outage , when the power came back on ; to open the garage door you have to keep pressing the remote two or three times before it opens all the way . Any suggestions ? Would you recommend tightening the torque spring ? To give more tension ?
Hi I have a question. The green led light on the linear keypad for one of my garage door opener is shows opposite. The door is closed the green led light shows is lit on the top. Is there a way to fix it. Also I bought an MyQ Chamberlain WiFi garage hub and I am trying to pair it to the 2 car garage door. For some reason both the garage door gets synced and it’s not working as expected. Any thoughts on that ?? Appreciate your response. Thank you!!
Open and close wall mount works fine....I can also open door with remote, however it will not close using remote. I noticed one of the sensors wasn't lit. Noticed the wire was cut, so I spliced together...still no power on the sensor. Next step is for me to check power...what volts Should I look for on sensors?...thank you.
My linear LD033 the clicker has to be within 3 feet of the opener for it to work, the learning light is always on, kinda flickering but always on. wall panel works. reprogrammed the opener, changed battery, clicker works on another door. erased memory and reprogrammed it, unplugged the opener and non worked, any tips
Is there a way to adjust or reset the light timer? It used to stay on for about 5 minutes after opening or closing, then suddenly dropped to 10 seconds. How can I get it back to 5 minutes? Thanks.
I bought the one-button remote off Amazon-says it's compatible with my LDCO800. All the lights do what they do on this video, but it doesn't open or close the door. The red light comes on the opener when I press the button on the remote-so it's getting the signal, but nothing happens. Can anyone help?
+FABIOLA JIMENEZ The neighbor needs to clear the codes off their opener and then retrain it to only their remotes. There is nothing you can do, they need to do it.
What is the problem if, when I click the button on the remote to send a signal to the opener, nothing happens? The light flashes on the remote, but the opener doesn’t register that it’s been programmed.
+nakia bellamy I have two videos that may help for that. Let me know what you find. ruclips.net/video/FTzA7oXy8fM/видео.html and then if you dont find your problem watch this one ruclips.net/video/uSyI-zbpxEc/видео.html
Wall station is not the sensors. The wall station is the buttons on the wall used to open the garage. Usually by the entry door. This video shows you should not be giving advice yet.
Hi I have a question. The green led light on the linear keypad for one of my garage door opener is shows opposite. The door is closed the green led light shows is lit on the top. Is there a way to fix it. Also I bought an MyQ Chamberlain WiFi garage hub and I am trying to pair it to the 2 car garage door. For some reason both the garage door gets synced and it’s not working as expected. Any thoughts on that ?? Appreciate your response. Thank you!!
visting my elderly mom, she thought it was her remote batteries...your video saved me over $200 and without your video, i wouldng have know what to do to fix this. your going through the flashing of the lights, i never would have been able to read them, and you made it possible to show me it was the vacation switch! thank you so much!
I was to spend a lot, but after your post I was able to fix. Awesome. Thank you Adam for saving my money.
I tried to use a Genie remote and a Chamberlain universal remote. Both would not work properly. I had to use a Linear remote to finally get it to program. Not Lowe's and Home Depot do not sell Linear remotes. What a journey.
5 flashes was killing me. Didnt realize it was an easy switch on the wall. Thanks!!
Thank you for this video. You helped me figure out vacation mode (4 blinks) which is why my new clicker wouldn't program. I pushed the wall switch up as you instructed and the clicker then programmed on the first try.
Great tutorial Adam. Thank you.
We had the exact model, we had a power outage, and something is off. The clickers are only working in a close range, like 2 feet. I changed the batteries in them and reconnected them with the unit. Any suggestion what's wrong? I even changed the light bulb, and it's the one that doesn't interfere with the range. I played around with the antenna as well... nothing change. Any suggestion??
Hi Adam,
I have the same opener, what is that model ? I can't find the model label on mine.
Is this a LDC0800?
I’ve got the same lift motors as in your video. Have you ever had a motor go out? My door raises and closes with just a finger. With the door detached from the drive chain, the motor has trouble running just the chain. Can the motor be lubricated? The unit is a little over 2 years old. Any help would be greatly appreciated. Thank you.
Thank you for this. I just programmed my remote I bought off Amazon in a matter of 10 seconds. Amazing.
This was super helpful! Thank you!
I've tried everything and cannot program the keypad and remote. Either one or the other will work. Can you help me? Thanks Denise
I wonder if you could help , we think the torque spring needs to be adjusted tighter . The garage door opens a little less than half way . This happened after a power outage , when the power came back on ; to open the garage door you have to keep pressing the remote two or three times before it opens all the way . Any suggestions ? Would you recommend tightening the torque spring ? To give more tension ?
Easy fixed....thanks man
Hi
I have a question. The green led light on the linear keypad for one of my garage door opener is shows opposite. The door is closed the green led light shows is lit on the top. Is there a way to fix it. Also I bought an MyQ Chamberlain WiFi garage hub and I am trying to pair it to the 2 car garage door. For some reason both the garage door gets synced and it’s not working as expected. Any thoughts on that ?? Appreciate your response. Thank you!!
Thanks
can you make a video of the opener running? I'm just curious on how it runs
Adam I have changes my batteries in remotes and tried to program remotes. My opener learn buttom stays red all the time. What does this mean?
Open and close wall mount works fine....I can also open door with remote, however it will not close using remote. I noticed one of the sensors wasn't lit. Noticed the wire was cut, so I spliced together...still no power on the sensor. Next step is for me to check power...what volts Should I look for on sensors?...thank you.
Have the same problem, did you get it figured out boss?
Hi, I have question & it looks like you have the answer on how I can pair this linear garage with a Mercedes Benz Homelink?
My linear LD033 the clicker has to be within 3 feet of the opener for it to work, the learning light is always on, kinda flickering but always on. wall panel works. reprogrammed the opener, changed battery, clicker works on another door. erased memory and reprogrammed it, unplugged the opener and non worked, any tips
Is there a way to adjust or reset the light timer? It used to stay on for about 5 minutes after opening or closing, then suddenly dropped to 10 seconds. How can I get it back to 5 minutes? Thanks.
excellent very easy too program and use thanks sew much
Hello. My learn button light remains on. No matter what. Any suggestions. Thanks
Where do you find the ID to use a remote attached to the outside of garage
I have a problem with my garage door opener going down and reversing. It seems as if it is trying to close more than is allowed. How do I adjust this?
The red light on the main box (the one on the ceiling) has the red light flashing but it is a bit faded... continuously...
why would the trolley back up two inches after opening
I have a LD033, how do I delete the current keypad code and then program a new 4 digit code? Thx
I bought the one-button remote off Amazon-says it's compatible with my LDCO800. All the lights do what they do on this video, but it doesn't open or close the door. The red light comes on the opener when I press the button on the remote-so it's getting the signal, but nothing happens. Can anyone help?
@Adamdiy Can a control be deprogrammed ? If yes then how? Our neighbors garage is opening with our control :\
+FABIOLA JIMENEZ The neighbor needs to clear the codes off their opener and then retrain it to only their remotes. There is nothing you can do, they need to do it.
+AdamDIY Thank you!
Can't they just reprogram their opener with a new code? Instead of bothering the neighbor?
The learn button turns on every time I use the remote but the door never opened.
What is wrong if the door will only open half way up and will not open by the remote at all
When trying to program 2 more remotes it does not work
Should've went with a Highlift Package.
Mine doesn’t have lights on the remote though
What if your learn button doesnt stay on for you to program it?
Garage door is receiving the signal with my remote but it isn't opening help?
What is the problem if, when I click the button on the remote to send a signal to the opener, nothing happens? The light flashes on the remote, but the opener doesn’t register that it’s been programmed.
I did it the same as you connected but I try to open it and it did work and I try to closed it did not work
The door opens by the remote but will not close
Any ideas
Flashes 4:43
Key pad works but remote will not
Mine won’t program for some reason
I have a solid red light on the back of this door opener , so the remotes will not work
My garage door opener reads that it’s trying to learn but it doesn’t open
Como traduzir brasileiro
you didn't say at all how to trouble shoot #7. all you did was read it....
My garage door won't open all the way. It comes up little bit and than stays there. Need help!
+nakia bellamy I have two videos that may help for that. Let me know what you find. ruclips.net/video/FTzA7oXy8fM/видео.html and then if you dont find your problem watch this one ruclips.net/video/uSyI-zbpxEc/видео.html
Queria importar
Wall station is not the sensors. The wall station is the buttons on the wall used to open the garage. Usually by the entry door. This video shows you should not be giving advice yet.
Hi
I have a question. The green led light on the linear keypad for one of my garage door opener is shows opposite. The door is closed the green led light shows is lit on the top. Is there a way to fix it. Also I bought an MyQ Chamberlain WiFi garage hub and I am trying to pair it to the 2 car garage door. For some reason both the garage door gets synced and it’s not working as expected. Any thoughts on that ?? Appreciate your response. Thank you!!
One more thing your sensors/photo eyes should be between 4 and 6 inches from the ground.