What intake manifold are you running? On my 03 AWD AT, two weeks ago I did the RBB swap and ported both the RBB and the Manifold base - both parts were less than $100 (used) on ebay, and swapped out the fuel rail ~ $30.. :) And Injen Cyborg Intake. Watched your RBC port video for inspiration - so THANKS!!! She's now a champ for commuting on the interstate. As you know with the 03 auto there's no tuning option, but I was just about to run a 3" exhaust for S's and G's but now i think i'll run this 1320 header and some fun exhaust combo to the rear - so thanks for more inspiration. Element vids A++
Thanks man! My stuff is still all stock. I’m really not trying to dump a ton of money into it it’s just the daily. Trying to save my money for my race car!
Great work thanks for making this. What size pipe did you use? I am guessing it was 2.5"? I will probably eventually do something similar on one of my Elements. Thanks again for sharing.
@pop_pops_garage gonna tune it or increase the intake at all? Like dyno tune? I figure cheapest way to get some more power is all 3. I carry a lot and want just more low end power not really to go faster.
Did you swap the o2 sensors yet? I just installed this same header but also have CEL on for the sensors but mine are fairly new but still throwing code.
@@pop_pops_garage I think I'm going go have to get new sensors also. Otherwise these headers are awesome and the fitment is fantastic, but the 3 bolt flange absolutely needs to go. You definitely did the right thing by swapping to v-band. I'll be doing the same soon
@@guyguy1736 i put the new sensors in last night and still have a cel. I’m going to undo the battery today and see if i can reset them and see what happens. The thing i don’t like is the doughnut gasket doesn’t have spring bolts to make it work, i tried using the stock ones and they won’t work with the flanges. I need to find some way to make spring bolts work or this thing will just keep loosening up over time
@@pop_pops_garage use some aftermarket ones like from autozone or napa. They have some that are slightly larger that should work. I'm actually on my way to look for them myself right now. I wasn't a fan of that gasket either tbh. It seems like a dhit gasket so I'm goi g to see if I can get a better one also
Love the sound. Does sound a little like the Subaru, which I Like.
@@oscarzambrano6127 it’s grown on me more!
Nice!!! Adds a "Honda" "Element" to your content haha, I like it.
I’ve got a couple element videos on here already! They are great daily drivers!
MT Ralley Red FTW!! Helllllls yeah dude! Just hope your RTAM is safe and strong.
she good!
I’ve always wanted an Element.
Just do itttt
Do iiiiiiit. Best daily ever.
You can have mine lol, it’s reliable af but I don’t like the green
@shanedottie ill take it im broke af I don't care of the color he'll at this point I'd drive a pink one
@@shanedottie Where are you? Is it manual, and how much $?
That exhaust sounds sick and much respect!!!!
thanks!
sounds and looks great. I wish you made more. my 2011 is rusted the eff out
@@jst287809 I’d like to make some, shipping would just be silly
Nice job and it sounds good and not raspy. FYI, did sound like you have a front axle making noise during one of your turn arounds during the drive.
yah its since been replaced haha
Does sound good. I would want something pretty quiet too. Turn downs do make it a bit louder I believe.
Maybe a little bit. I’ve gotten use to it now it’s not bad. If i wanted it quieter I’d probably throw in another resonator or something
What intake manifold are you running? On my 03 AWD AT, two weeks ago I did the RBB swap and ported both the RBB and the Manifold base - both parts were less than $100 (used) on ebay, and swapped out the fuel rail ~ $30.. :) And Injen Cyborg Intake. Watched your RBC port video for inspiration - so THANKS!!! She's now a champ for commuting on the interstate. As you know with the 03 auto there's no tuning option, but I was just about to run a 3" exhaust for S's and G's but now i think i'll run this 1320 header and some fun exhaust combo to the rear - so thanks for more inspiration. Element vids A++
Thanks man! My stuff is still all stock. I’m really not trying to dump a ton of money into it it’s just the daily. Trying to save my money for my race car!
I want a manual awd element. Muffler sounds good.
They are a blast! Thanks!
Great work thanks for making this. What size pipe did you use? I am guessing it was 2.5"? I will probably eventually do something similar on one of my Elements. Thanks again for sharing.
Yes i used 2.5in stainless steel
Nice job man! Sounds great
@@4defy772 thanks! The friend group always jokes with me because it sounds way to good for a suv haha
@@pop_pops_garage haha, I've got the SC and gotta say the inside noise is way more dampened then the EX/LX. That's what tunes are for!!!
@@4defy772 that’s rad!
I like the Element content 👍🏻👍🏻
@@PhillyMK3 maybe i need to film an element adventure video soon!
You're in Maryland? I'd love to come visit your inspiring PopPops garage & learn! I'm shopping for an Element now.
i just work out of my house! im in maryland but the next event ill be at will be doricon september 27-28 in shenandoah va at shenandoah speedway
Was considering the Yonaka catback but after watching this idk…🤔 Sounds dope man! 🤙
This setup sounds sick! Idk what the price difference would be though
Can and will you make another one? What would you charge for it???
im about to make another one for someone else but the issue is that i dont have a stock element here to make it meet up to a stock cat :(
Sounds better than my FL5 Type r😂😂😂. I wish I could buy one for my Element
@@didiermejia780 haha! They can be made! All the parts are available!
Sounds awesome! Nice
Thanks!
Killer man!!! I need!!!! 💪🏼💪🏼
🤘🏼
Great job.... sounds good
Thanks!
love it im in maryland too i got elements!
Nice!
Can this be done to a fwd auto element
@@mathewcaratini1182 yup! I’m actually posting a video tomorrow! I just did a fwd element!
o2 sensor spacer may help your check engine light problem
Yah i think i burned this one up trying to get it out of the cat
Think it increases hp at all maybe with a new intake?
it defiantly increased hp, i think its mainly the header that made the most noticeable difference. im sure all of it helps though
@pop_pops_garage gonna tune it or increase the intake at all? Like dyno tune? I figure cheapest way to get some more power is all 3. I carry a lot and want just more low end power not really to go faster.
@@cdotson0027 elements are kind of a pain to tune.
@pop_pops_garage I'm sure someone who is good and has the right machines can right? Like a dyno tune.
@ you have to get hondata or a tunable ecu and that’s where it can become a pain. Only a couple
People make copatable stuff
How much including shipping?
I unfortunately don’t have a way to ship them reasonably. I just make them locally to each car
Drone?
@@bhadz100 it’s not to bad! There’s definitely noise in the car but that’s to be expected with as short of gears as these things have
Soooo jelly dude. It sounds so good. Is the header uel tubes?
nope they are all normal lol
I need the Corolla 👀
That was a customer car that i didn’t even end up working on haha .
did you use a pipe bender, or did u cut down pre bent pieces?
Cut pre bent stuff
Did you swap the o2 sensors yet? I just installed this same header but also have CEL on for the sensors but mine are fairly new but still throwing code.
I legit just picked some up today! I’ll be installing and driving tomorrow
@@pop_pops_garage I think I'm going go have to get new sensors also. Otherwise these headers are awesome and the fitment is fantastic, but the 3 bolt flange absolutely needs to go. You definitely did the right thing by swapping to v-band. I'll be doing the same soon
@@guyguy1736 i put the new sensors in last night and still have a cel. I’m going to undo the battery today and see if i can reset them and see what happens. The thing i don’t like is the doughnut gasket doesn’t have spring bolts to make it work, i tried using the stock ones and they won’t work with the flanges. I need to find some way to make spring bolts work or this thing will just keep loosening up over time
@@pop_pops_garage use some aftermarket ones like from autozone or napa. They have some that are slightly larger that should work. I'm actually on my way to look for them myself right now. I wasn't a fan of that gasket either tbh. It seems like a dhit gasket so I'm goi g to see if I can get a better one also
@@guyguy1736 my cel went off yesterday!
Any seat of the pants hp gains?
Yes i can for sure tell a difference
Great content! Do you have a link to the exhaust manifold or which CRV it’s for? Tried searching 1320 RD1 Exhaust Manifold but not having any luck.
Thanks! Everything is linked in the description. Also the rd1 is b series you need the k series crv header
Oh man I feel like an idiot. Just a little click and everything would’ve been clear. Thanks for the kind reply, subbed for more content!
@@stevenrodriguez3982 thanks!
what year is your element?
2005
Which vibrant muffler did you use?
@@04mrccycgarza just the normal
Street power one
I knew that your Element was a stick shift!
Yup! I don’t own any manuals
Sounded like a Subaru when you drove off
Yah haha it’s kinda crazy idk why it sounds like one but it does haha