👍 If you found this video helpful, make sure to smash that "LIKE" button and "SUBSCRIBE" for a steady stream of DIY knowledge and product review! Stay empowered to tackle any project around your home, car, or pool with confidence. Let's get hands-on and make life easier together! www.youtube.com/@diymanual?sub_confirmation=1 And if you are planning on making a purchase on Amazon, you can support my channel by using my Amazon affiliate link below. Purchasing through an affiliate link does not cost you anything extra but it helps support the efforts of small creators like myself. Vevor 2.8HP 1920lbs: amzn.to/3TSRQMr Vevor 6.5HP 4200lbs: amzn.to/3tDXveL More Options: amzn.to/3vjnxUS Main Affiliate Link : amzn.to/3Ha4fny Thank you for your support. 🏡🚗🏊♂ #DIYLife #SubscribeForMoreDIYTips
PERFECT!!!! Just got mine yesterday, the factory clip with NO SOUND...SUCKED!!!! Yours is perfect and direct to the point without knowing your dog or your kids names or staring at the camera with oversize rainbow sunglasses .... Thanks brother and keep them coming.,
Very helpful video, good job. Only comment is Bar & chain oil normally has a tackiness additive and a solvent for tree sap. It should never go in an engine.
Finished putting mine together using your helpful video. I just need to tighten the throttle nuts tomorrow. The box had no damage but one of the oil cap was loose and machine was kind of covered in oil. I thought there is no oil in the motor itself. I also heard some kind of clinking noise in the fuel tank. Is that normal???
Thanks for the input and yes I did read the manual and you just made me look at the manual again to see if I missed it but I did not see anything about starting a compactor on hard surface will damage the unit. If you have the manual please let me know what page is it located so I can check again. I don't see a problem with starting it on hard surface, because simply starting it with throttle at low position like what I did on this video will not cause it to vibrate. I would assume you mean to not let this run on hard surface? Because letting this run on a hard surface with the throttle on 3 or above will damage the unit or even crack the surface as it will start jumping around uncontrollably. It's not in the manual too but it just common sense. This video is simply to show how to setup and start the equipment. I have another video on this where I showed how to actually run this to compact a surface. And thank you for commenting because I was looking for it to include the link here but it looks like I did not post it yet. I just moved all my old files in the storage and hopefully I was able to save it. I will post it once I found it. Thanks.
👍 If you found this video helpful, make sure to smash that "LIKE" button and "SUBSCRIBE" for a steady stream of DIY knowledge and product review! Stay empowered to tackle any project around your home, car, or pool with confidence. Let's get hands-on and make life easier together! www.youtube.com/@diymanual?sub_confirmation=1
And if you are planning on making a purchase on Amazon, you can support my channel by using my Amazon affiliate link below. Purchasing through an affiliate link does not cost you anything extra but it helps support the efforts of small creators like myself.
Vevor 2.8HP 1920lbs: amzn.to/3TSRQMr
Vevor 6.5HP 4200lbs: amzn.to/3tDXveL
More Options: amzn.to/3vjnxUS
Main Affiliate Link : amzn.to/3Ha4fny
Thank you for your support.
🏡🚗🏊♂ #DIYLife #SubscribeForMoreDIYTips
PERFECT!!!! Just got mine yesterday, the factory clip with NO SOUND...SUCKED!!!! Yours is perfect and direct to the point without knowing your dog or your kids names or staring at the camera with oversize rainbow sunglasses .... Thanks brother and keep them coming.,
Thank you for the kind words! I appreciate your support.
Very clear step by step detailed instructions on how to set up and start the compactor. Well Done.
Your feedback means a lot, thank you for watching and appreciating the effort put into the instructions.
Thank you very much for this detailed video. It is a great help! Made the assembly and getting started quick and painless. Thank you again!
Your kind words mean a lot to me. Thank you for watching and sharing your feedback!
Very helpful video, good job.
Only comment is Bar & chain oil normally has a tackiness additive and a solvent for tree sap. It should never go in an engine.
Thank you so much for your input, I appreciate you watching the video!
Came here for the rubber band. Thank you.
Thanks for stopping by! Stick around for more fun content!
Mine came with a tool that looks like a wrench to remove lug nuts. Did you ever figure out what that was for?
@@ajaxsf Hi. I actually asked the same question to Vevor support. I was told that it is the sleeve for removing the spark plug. Hope this helps.
@@diymanual Thanks! That's a huge help and thanks for this video.
Finished putting mine together using your helpful video. I just need to tighten the throttle nuts tomorrow.
The box had no damage but one of the oil cap was loose and machine was kind of covered in oil. I thought there is no oil in the motor itself.
I also heard some kind of clinking noise in the fuel tank. Is that normal???
I don't notice a noise in the fuel tank. Maybe take a peek inside the tank it's probably just a loose part?
Crazy, I removed the rubber band, and there was no hole. @diymanual
I think the rattle in the tank was the chain to the fuel cap.@@diymanual
Any idea what to do if there is no vent hole under the rubber band on the vibrator box? Can it still be run?
I guess that will be best answered by the manufacturer.
Thanks for doing this. Woulda been nice if they put any of the setup info into the manual 🤦🏻♂️
Thank you for your kind words! I'm glad I could assist you.
So, the quart of oil said "bar oil" is that what you put I. The engine?
Did you bother to read the manual? It should have mentioned starting a compactor on hard surfaces like concrete eventually damages the unit.
Thanks for the input and yes I did read the manual and you just made me look at the manual again to see if I missed it but I did not see anything about starting a compactor on hard surface will damage the unit. If you have the manual please let me know what page is it located so I can check again.
I don't see a problem with starting it on hard surface, because simply starting it with throttle at low position like what I did on this video will not cause it to vibrate. I would assume you mean to not let this run on hard surface? Because letting this run on a hard surface with the throttle on 3 or above will damage the unit or even crack the surface as it will start jumping around uncontrollably. It's not in the manual too but it just common sense.
This video is simply to show how to setup and start the equipment. I have another video on this where I showed how to actually run this to compact a surface. And thank you for commenting because I was looking for it to include the link here but it looks like I did not post it yet. I just moved all my old files in the storage and hopefully I was able to save it. I will post it once I found it.
Thanks.
Bar & chain oil is not the same as motor oil. I'd be careful using that. It's meant to be sticky to stay on a chain. Otherwise, thanks for the video
Thank you for the info.
Great video! What octane gas do you put in it?
I used 92 Octane.
Thanks for the great video! It helped a lot with getting mine set up.
You are welcome. I'm happy to help.