Can't you just design a different board for each possiblity(xbox left, xbox right, ps left, ps right), that way it would be much easier to install them, but i don't know anything about pcb design so i don't know how hard this would be to do
Do you have a written out instruction or pdf walkthrough how to activate each mode after installation? I have watched video walkthrough numerous time and have been unable to enter any calibration mode.
I need tools, my ex took all my tools when she left me. She said something to the effect that I never listened to her. Tbh I don't really know I wasn't paying much attention. Thx for the vid, as soon as I get some tools I'm gonna try this.
@@Jeff_Jaguar Do you multiple personalities or something? Cuz you said, "WE" as if you are more than one person... Anyways ty for taking the time to read my short story, lol.
Wow, I'm trying to sold these but this seems nearly impossible, and i consider my self decent at soldering, i follow all the steps but the Y axis is totally gone.
You mentioned the Dualsense 5/DualShock 4 +V4 version driver board, does the JDM040 fall under that? I am not sure which model number the V4 version falls under, JDM or JBM. Also, is this adjustment board compatible with the orange stick module that was used in the past for favor.onion's Dualsense and DualShock 4?
3:06 Solders the centre pin in with the sleeve still in place & snips the tops later to attach a wire. 4:13 Button 🔘 pin bridged to a PCB pad 🤷🏼♂️. 5:46 Snip the sleeve length. 7:32 Wire slipped into center sleeve & soldered. 8:58 Centre pin bridge wired to a PCB pad 🤷🏼♂️. 10:48 PS5 Dualsense, 2 solder bridge points. 11:20 PS4 Dualshock 4 example different bridge solder points. Don't ask me how it all works it's a polarised 🧲 - / + chip current ⚡🔋🪫 flow direction thing on an auto calibration added PCB to my knowledge 🫠🙃🤤. More complicated than I can figure out. But I did try to lay out a video study of my own or 2++++ 😁 lol. Ohm's resistance value of trim pots study in relation to circularity & deadspot 🎯 resizing. I tried to scrape together fundamental Hall Effect stick 🕹️🕹️ knowledge for the console strength numbers & electrical ⚡ polarity differences across the available hall pots, to try to know what we are looking 👁️👁️🥹 at 👍🏼 lol...
Thanks for the tutorial. By the way, the PS5 Kit sold out, so is it possible to buy the PS4 Kit and use it for my PS5 controller? I just need to bridge the right solder points, right?
Circuit noise and adjustment difficulties are problems that can occur in direct installation. If you don't need a joystick, you don't need a drive plate.
Is there a way to keep the haptic feedback in the left grip, would it interfere if a small wire was soldered to the pads that show just under your pcb so that the actuator could still function.
@@junZeng-520 ok, thank you, I am going to get a pair of sticks soon, I tried the flexible pcb with pots but they just made the problem worse, you have made an amazing fix for something that has been with us for a long time, and thank you for the work you've put into the hall effect thumbsticks.
Hello, I saw your videos and I am interested in having a control with a Hall effect, but I am not good at doing repairs. Could you sell me a reconditioned control with a Hall joystick? I'm from México
Hi Jun, I'm looking to buy just the driver board, but I dont see it as an option on aliexpress. Any help from you or anyone else would be greatly appreciated. I've tried to reach you through whatsapp and email.
@@junZeng-520 my brother has these flex pcbs (the ones where you can adjust the x and y axis for the case your stick should start drifting)...do these also work? If yes, i could use these.
@@BaamAlex those are not really a replacement for these PCBs. If you are installing it on a PS4 controller, I believe there is software available to program the calibration of the new sticks on to the controller (similar to how Sony calibrates them at the factory). You will still have the jitter which this PCB filters out. If you are using a PS5 or Xbox controller, then you need this PCB to get the best performance out of the new sticks. Without it there is often jitter and an outer deadzone, because the controller's board is expecting slightly different information than the hall effect stick outputs.
@@vinny3139 Nice! Can You post some photo of the installation? Do the original IC + tiny resistors next to it soldered on the pcb of the original DS edge stick module, interfeere with the mod's pcb? No need to shim the mod's pcb?
@@MarkV92 It going to sit a little bit above the solder points so itll need a little extra solder becuase there is a chip that sit under the edge module. you will need a dremmel to shave the plastic inside
We are in the 21st century, why invent expensive calibration boards for analogs? Calibration programs are already available, we just need a good programmer who could improve these programs
@@junZeng-520 | Jun | refrain from making disrespectful comment about our dear customer from Phillipine nation. Have a chat to me in my office. - Manager Wu-xia Chao
Yesterday I received the kit, so far I installed it only on the right stick, everything works great. Thank you so much!
Hi,where are You from?
How long did it take for your order to arrive?
¿Hola cuánto tiempo tardó en llegarte este kit?
¿De cual país eres?
Can't you just design a different board for each possiblity(xbox left, xbox right, ps left, ps right), that way it would be much easier to install them, but i don't know anything about pcb design so i don't know how hard this would be to do
Thank you for the extra hall sticks! Looking forward to the build 🤙
Do you have a written out instruction or pdf walkthrough how to activate each mode after installation? I have watched video walkthrough numerous time and have been unable to enter any calibration mode.
I need tools, my ex took all my tools when she left me. She said something to the effect that I never listened to her. Tbh I don't really know I wasn't paying much attention. Thx for the vid, as soon as I get some tools I'm gonna try this.
You could have just said "Thx for the vid, as soon as I get some tools I'm gonna try this."
We didn't need to know about your ex.....
@@Jeff_Jaguar Do you multiple personalities or something? Cuz you said, "WE" as if you are more than one person... Anyways ty for taking the time to read my short story, lol.
Sue her on judge judy for your tools. I'll watch with popcorn 😅
@@heyguyslolGAMINGno, I definetly want him to get his tools back. Lol
Wow, I'm trying to sold these but this seems nearly impossible, and i consider my self decent at soldering, i follow all the steps but the Y axis is totally gone.
Hi!! I want to ask you a question.
Between Besavior and Hall sensor, which one should I put on first and shoulder
You mentioned the Dualsense 5/DualShock 4 +V4 version driver board, does the JDM040 fall under that?
I am not sure which model number the V4 version falls under, JDM or JBM.
Also, is this adjustment board compatible with the orange stick module that was used in the past for favor.onion's Dualsense and DualShock 4?
why put silicone insulation on the center contact? Previously, it was possible to simply solder the board directly to all contacts
3:06 Solders the centre pin in with the sleeve still in place & snips the tops later to attach a wire.
4:13 Button 🔘 pin bridged to a PCB pad 🤷🏼♂️.
5:46 Snip the sleeve length.
7:32 Wire slipped into center sleeve & soldered.
8:58 Centre pin bridge wired to a PCB pad 🤷🏼♂️.
10:48 PS5 Dualsense, 2 solder bridge points.
11:20 PS4 Dualshock 4 example different bridge solder points.
Don't ask me how it all works it's a polarised 🧲 - / + chip current ⚡🔋🪫 flow direction thing on an auto calibration added PCB to my knowledge 🫠🙃🤤.
More complicated than I can figure out.
But I did try to lay out a video study of my own or 2++++ 😁 lol.
Ohm's resistance value of trim pots study in relation to circularity & deadspot 🎯 resizing.
I tried to scrape together fundamental Hall Effect stick 🕹️🕹️ knowledge for the console strength numbers & electrical ⚡ polarity differences across the available hall pots, to try to know what we are looking 👁️👁️🥹 at 👍🏼 lol...
I install it on a PS5 controller tested it and calibrated. Then I charge my controller after using it, now it wont turn on anymore 😢.
Will you sell the modules without the included joysticks? When will you have the xbox modules back in stock?
Thanks for the tutorial. By the way, the PS5 Kit sold out, so is it possible to buy the PS4 Kit and use it for my PS5 controller? I just need to bridge the right solder points, right?
I will update the inventory, if you need ps5, please let me know in advance.
Glad I ordered when I did. My PS5 kit just arrived 😊
@@junZeng-520 Hello, the link shows PS5 out of stock, can you make more?
@@junZeng-520I am looking to buy two sets if you could please update the inventory. Thanks!
@@spectrepro I will update the inventory today.
曾兄您好!我非常高興您做出這麼棒的產品,我想把這也用在PC的搖桿控制器上,可以請教霍爾感應器的電壓規格以及模組從左到右的三隻腳位定義嗎?謝謝!
Hello, when will the Xbox kit be available ?
Hi! can you make a video with details installation for hall effect sticks for xbox series x controller with close up camera view? Thanks
Check out my other videos
Do you guys have any tips to solder the middle pin ?
Does the product some with instructions? This video was cleat as mud
Just ordered for my PS5 controller 😊 thank you for the video tutorials and hard work Ying Jun 👍
Thank you. If you encounter any difficulties during installation, please contact me and I will try my best to help you.
If it wouldn’t be such a hassle can you pls make a video just for ps4
Why do we need those insulation tubes in the middle ? what is it purpose ?
It is for... insulation? I made the same mistake and didn't use it. You can't calibrate the sticks when you don't use it.
Hi! I cannot choose my country (Uruguay) as an option in aliexpress for your product. Is it any way to buy your product from here? Thanks!
Are drift fix v1.5 pcb's compatible w hall effect joystick on dualsense?
and why is it bad to just solder 3D analogues on the hall sensors without this additional board?
Circuit noise and adjustment difficulties are problems that can occur in direct installation. If you don't need a joystick, you don't need a drive plate.
Hey bro, I want to buy a ps4 kit from you soon. What model joystick do you ship? K-silver jh?? Thank you
I mainly use k-silver modules.
Is there a way to keep the haptic feedback in the left grip, would it interfere if a small wire was soldered to the pads that show just under your pcb so that the actuator could still function.
You need to scrape off the solder resistance next to it and then connect it
@@junZeng-520 ok, thank you, I am going to get a pair of sticks soon, I tried the flexible pcb with pots but they just made the problem worse, you have made an amazing fix for something that has been with us for a long time, and thank you for the work you've put into the hall effect thumbsticks.
@@junZeng-520could you do a tutorial for this?
@@raphaelricardinoyeah that would be great
Just so you know scrape off the green layer next to the covered up black wire contact CAREFULLY and solder to the exposed copper
Hello, I saw your videos and I am interested in having a control with a Hall effect, but I am not good at doing repairs. Could you sell me a reconditioned control with a Hall joystick? I'm from México
what temperature do you use for soldering and for desoldering?
The soldering iron temperature I use is 300 degrees Celsius, and the hot air blow welding I use is 350 degrees Celsius. Solder used with 63% Sn 37 Pb。
@@junZeng-520 awesome thanks!
Do any of them work with Xbox 360 and PS3 controllers?
Sorry, there is no installation location for 360 and ps3
Hi! Do these pcb's also work with the original potentiometers?
If yes I'd like to try to weld them into my Xbox elite series 2.
If you work with the original potentiometer, you can only solve the problem of correction, not the problem of drift.
@@junZeng-520i just only want to change the center point, can i just use my original thumbsticks and install the pcb board?
@@alejandro4797 This can be changed, but it is not recommended. Traditional joysticks have an unstable life
Hola,@@junZeng-520es el único que vende este item.El te vende el kit completo 2 pcb drivers board and 2 hall effec joystick
你淘宝店是什么?我过两天去大陆几个星期想直接在淘宝买。
可以的。有社交软件吗?
Hi Jun, I'm looking to buy just the driver board, but I dont see it as an option on aliexpress. Any help from you or anyone else would be greatly appreciated. I've tried to reach you through whatsapp and email.
I also bought some hall effect sticks. But without the pcb. Do i really need this pcb or can i calibrate these sticks without it somehow?
Without this drive board, it's very difficult to adjust. And jitter
@@junZeng-520 my brother has these flex pcbs (the ones where you can adjust the x and y axis for the case your stick should start drifting)...do these also work? If yes, i could use these.
@@junZeng-520 but you can adjust the x and y axis without it?
@@BaamAlex those are not really a replacement for these PCBs. If you are installing it on a PS4 controller, I believe there is software available to program the calibration of the new sticks on to the controller (similar to how Sony calibrates them at the factory). You will still have the jitter which this PCB filters out.
If you are using a PS5 or Xbox controller, then you need this PCB to get the best performance out of the new sticks. Without it there is often jitter and an outer deadzone, because the controller's board is expecting slightly different information than the hall effect stick outputs.
@@OmairArif nvm. I found a video. You can calibrate the sticks without these little Mainboards. It's a bit finicky, but it's doable.
Hi, do the back PCB fit into the Dualsense edge stick module?
Hello, the Dualsense edge module is still under development.
@@junZeng-520 Wonderfull, do You have any ETA on that? (1 month, 2 months.... 1 year)
I just installed mine on my edge today, i can confirm that it will work, but youll have to shave some plastic off inside the module
@@vinny3139 Nice! Can You post some photo of the installation?
Do the original IC + tiny resistors next to it soldered on the pcb of the original DS edge stick module, interfeere with the mod's pcb? No need to shim the mod's pcb?
@@MarkV92 It going to sit a little bit above the solder points so itll need a little extra solder becuase there is a chip that sit under the edge module. you will need a dremmel to shave the plastic inside
Do you sell ps5 board+hall joystick+pcb calibration+calibrated?
Yes, I sell on AliExpress
@@junZeng-520 do you sell as a packaged?
is it available on shoppee or lazada?
Aliexpress lng sa ngayun
Hey does anybody know if the Hall effects joystick would work on the Xbox elite series 2?
Yes, it can
We are in the 21st century, why invent expensive calibration boards for analogs? Calibration programs are already available, we just need a good programmer who could improve these programs
where can we buy in the Philippines?
Is AliExpress available in the Philippines?
@@junZeng-520 | Jun | refrain from making disrespectful comment about our dear customer from Phillipine nation. Have a chat to me in my office.
- Manager Wu-xia Chao
国内做不做?有淘宝或是闲鱼吗
国内加我微信:zengjun1995
耐久性どうなのか知らんけど値段高すぎるってもっとロット売りで安くしてくれないと
Just ordered a set for ps4, whats better to contact you with, whatsapp or gmail?
the pcb isn't needed for ps4 my guy, look for ds4 tools you can use it to calibrate them.