Very informative and helpful!!!! My Neptune 3 Plus is scheduled to be delivered tomorrow, so I'm really looking forward to setting it up and see how it does for me!!! Thanks again for taking the time to share your experiences with us!!!
@@Splatdash quite easy to level. Do the 6 point manual level 1st and keep going around the 6 outside points until all feel the same, then tap the center/home button to continue into the auto leveling segment. Then, do the zero home to finish things off. I love this printer and will be getting a second one shortly!!! Well worth the $$$$.👍
I love the setup the colors and the quality of this video, this printer is incredible too. Underrated. Though it’s always nice to have some lofi or classical in the baclground
Thank you so much for this video it helped so much! This is the first 3d printer I've owned and I was super nervous to set it up but this video was a so easy to understand. :)
manual leveling brings it about 0.5 cm or so above the bed. Turning doesn't seem to be able to reach it or it's extremely slow. Could the manufacturer be really that far off with the rest of the knobs???
Great video, thank you for your thoroughness and attention to ever detail. Do you have a video where you do e-step calibration, or where you do a temp tower and modify the g-code so the printer pauses until the new target temperature for each new section of the print is reached before that section is printed? Cheers!
I turned on my printer after one day . But unlikely it's only showing red light in CR TOUCH. AND SCREEN IS SHOWING ONLY THR LOGO how the fix it pls need help in this.
Thank you for the video.. trying to follow along both of them. I can't even get #1 to touch no matter how much I spin it. #3 is so loose, regardless of what I do with the tool I use, I'm -2.20, so I'm assuming my prints will be terrible. Edit: Auto leveling won't even start. Gives an error about Z-axis.
I just went through with this procedure, starting with -2.10 mm Z-offset. I believe this value is related to the sensor, not the actual nozzle distance from bed. First preheat nozzle and bed to operating temps, select leveling menu, wait for homing, then adjust the -2.20 mm Z-offset value on the screen to touch center point with a piece of paper. Then start manual leveling with the same piece of paper between nozzle and bed, go around 6 points and adjust 6 knobs below bed, go around multiple times until no more adjustment needed. You can select the points again without leaving this menu. If finished tap the center home button on LCD. Finally put paper aside and confirm auto bed leveling to finish the task.
After 120hrs of printing I have issues with the bed leveling, like the extruder just print aligned only in the middle and right side of the bed but on the left there's like 1/2mm of distance from the bed and the extruder. Everything is tighten up and I do autocalibration+sheet a4 calibration but nothing changes.. Dunno how to solve that, it's a shame.
Can you tell me the actual area required? Looking for the area including the bed travel and that cable from the back of the bed. I ordered mine today, but I want to get a spot set up for it before it gets here
the left back side of the bed just wont go down (the nut is too tight and i cant tighten it more so the bed will go down - the same one you said in your video is way too loose) , what should i do?
@@D4ngel21 huh, i mean its a little bit of a perspective kind of thing, but it seems that they might have a slight fan quality issue then perhaps. I contacted support and they told be that my psu fan might be broken (i thought it had excessive noise) and would send me a replacement. So if you feel its abnormally loud, contact them about it.
![I.N "HALLUCINATION" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/n5B5q1Hwt_U/mqdefault.jpg)
Buy it here: geni.us/BuAQ2h
Recommended: geni.us/JustVlads
i own this printer and it’s been operating great, really do recommend it to anyone who’s into 3d printing:)
Very informative and helpful!!!! My Neptune 3 Plus is scheduled to be delivered tomorrow, so I'm really looking forward to setting it up and see how it does for me!!! Thanks again for taking the time to share your experiences with us!!!
How Is it is it easy to level
@@Splatdash quite easy to level. Do the 6 point manual level 1st and keep going around the 6 outside points until all feel the same, then tap the center/home button to continue into the auto leveling segment. Then, do the zero home to finish things off. I love this printer and will be getting a second one shortly!!! Well worth the $$$$.👍
@@ajones4064 did you get it to level the first try
I'm thinking of getting one and I'm scared of bed leveling because of my ender
@@Splatdash this is by far my favorite printer now. There are good videos that show how to go through the leveling process to make it pretty painless.
Very impressed with how refined and accurate this printer out of the box.
I love the setup the colors and the quality of this video, this printer is incredible too. Underrated. Though it’s always nice to have some lofi or classical in the baclground
Thank you so much for this video it helped so much! This is the first 3d printer I've owned and I was super nervous to set it up but this video was a so easy to understand. :)
manual leveling brings it about 0.5 cm or so above the bed. Turning doesn't seem to be able to reach it or it's extremely slow. Could the manufacturer be really that far off with the rest of the knobs???
Great Video! You helped me a lot! Thank you
Great video there aren't a lot of this particular printer just yet
Looks like they're in stock now.
Great video, thank you for your thoroughness and attention to ever detail.
Do you have a video where you do e-step calibration, or where you do a temp tower and modify the g-code so the printer pauses until the new target temperature for each new section of the print is reached before that section is printed?
Cheers!
I turned on my printer after one day . But unlikely it's only showing red light in CR TOUCH. AND SCREEN IS SHOWING ONLY THR LOGO how the fix it pls need help in this.
How did you end up resolving this?
why there is an offset between the head and the bed center when in home position?
Thank you for the video.. trying to follow along both of them. I can't even get #1 to touch no matter how much I spin it. #3 is so loose, regardless of what I do with the tool I use, I'm -2.20, so I'm assuming my prints will be terrible. Edit: Auto leveling won't even start. Gives an error about Z-axis.
I just went through with this procedure, starting with -2.10 mm Z-offset. I believe this value is related to the sensor, not the actual nozzle distance from bed.
First preheat nozzle and bed to operating temps, select leveling menu, wait for homing, then adjust the -2.20 mm Z-offset value on the screen to touch center point with a piece of paper.
Then start manual leveling with the same piece of paper between nozzle and bed, go around 6 points and adjust 6 knobs below bed, go around multiple times until no more adjustment needed. You can select the points again without leaving this menu. If finished tap the center home button on LCD.
Finally put paper aside and confirm auto bed leveling to finish the task.
@@ASCENSiON1989 Thank you! I was able to get everything setup :)
After 120hrs of printing I have issues with the bed leveling, like the extruder just print aligned only in the middle and right side of the bed but on the left there's like 1/2mm of distance from the bed and the extruder. Everything is tighten up and I do autocalibration+sheet a4 calibration but nothing changes.. Dunno how to solve that, it's a shame.
Cool machine
What filament did you use for the test print?
What do you do if it says probing failed
Can you tell me the actual area required? Looking for the area including the bed travel and that cable from the back of the bed. I ordered mine today, but I want to get a spot set up for it before it gets here
26" Wide 28" Deep (enough for bed wiring) and 36" Tall with 1kg spool.
the left back side of the bed just wont go down (the nut is too tight and i cant tighten it more so the bed will go down - the same one you said in your video is way too loose) , what should i do?
My off set is almost at 2.0 is that normal?
Hi! Have you used creality cr10v3? Is Neptune 3 plus better?
please help my is stuck in returning to zero and its does a sound like tatatatata
The PSU fan noise is friggin loud on mine, the printerhead is super quiet.
The fan on the hotend is also pretty noisy! Hope there will be a way to upgrade to very silent PSU + hotend fan.
@@D4ngel21 huh, i mean its a little bit of a perspective kind of thing, but it seems that they might have a slight fan quality issue then perhaps. I contacted support and they told be that my psu fan might be broken (i thought it had excessive noise) and would send me a replacement. So if you feel its abnormally loud, contact them about it.
@@jubb1984 Is the replacement much quieter?
i want it
Use metric plz
Another zzzzzzzzzzzz re-iteration of the same old tech over and over.
No one is revolutionary except maybe Bambu.
Lots of great features, affordable, good customer service... that's a winning combination for a lot of people. For me it's a great first machine.