Multi voltage ebike digital display | odometer digital cluster 48v 60v 72v
HTML-код
- Опубликовано: 12 сен 2024
- in this video we will see how to use Cluster display in Electric bike.
we will see how it shows different voltage, speed modes and Indications.
Electric bike voltage indicator.
Electric bike Speed indicator.
ebike LCD odometer,
ebike speed console
ebike LCD screen display
you can buy this from website below.
motorkit.in/lc...
For 72v you disconnect the black connectors and the red and black are for power. The white is for speed?
Blue for speed, in some display it may be different
@@InfiniteLaboratory I opened the back and it said white for speed.
Where is the speed signal coming from ? Is it pulse or variable DC voltage ?
Could you describe the calibration procedure?
2:25 blue wire speed ka wire h apny bola h lkin wo humy connect kaha karna h Q k motor me 1 to 3 phase ka wire h or aik wire me connector laga hua h jo k controller sy connect ho rha h to blue wire 3 phase k wire me lagana h ya kisi or me please detail me bata dyn
Thanks bro
Meter 12 volt pr on ho ga?
Can we connect this to pure ev epluto 7g because it's not showing percentage
where dose the blue wire goto
Can you maybe help me.
I recently buy one motorbike when the battery lithium 72v 30 Ah is connected, it always shows as 100% full with four bars on the speed display.
However, the issue is that the bars do not decrease while driving; it remains at 100%. When I travel around 50 kilometers , the battery runs out but I only get the low battery signal with the icon appearing just about 30 seconds to a minute before it's completely depleted. This means I never see the battery level drop; it's either full or empty, making it very difficult to manage the autonomy, knowing when to recharge, especially since it could run out when far from a charging point.
May me it is not calibrated
can you change the display of voltage to percentage
No.
i need to add dc 100V voltmeter to check battery voltage.
is the input negative for controller from battery and output negative terminal form controller same ? can i use any one negative point form controller and use 5-12 V positive for supply of dc voltmeter and a positive from battery terminal to check battery voltage?
i did that but am not getting actual battery voltage in the dc meter.
so please can u make a video for adding dc voltmeter to show actual battery voltage ?
This speedo max 96v not compatible 100v
Very nice
Bhai isme Pani Jake band ho gya hu repair ke liye kuch batao
I can't find voltage choosing wire, can u open the casing speedometer?
You can ask to supplier if your have same function or not
Can i install in my hero lectro cycle
No sir
Is sutable for 110cc bike and 12 v battery
No sir, only electric
Ye lfp battery me support karega
Yes
Is it now available
Yes
How can I buy
Contact us on 9409137897 or 9409137849 , or you can visit www.motorkit.in for all products
Display ka ac kharab ho giya kaha se mile ga sir
Can it work on 52volt battery
Yes
@@InfiniteLaboratory sir I have 51.2v 36ah lfp4 battery so you showing black wire connect or disconnect
Bro, MAC Cube speed unlock video please ....
No idea sir
Spidometer ini berapa amper?
?
black connect krne pr 60v aa raha hai disconnect karne par 72v aa raha h 48v kese aayega
The wire selection is for 60v, which cannot be auto detected because too much overlap with 48v and 72v, however if you have it set for 48v72v, the max voltage of 48v should be 54.6v so if below 54.6 it will select that range.
If it’s >54.6v it will assume it’s a 72v battery. So if you have a 52v battery its going to probably want to start in 72v when fully charged.
The only thing it really changes is the battery bar calibration (pretty much useless anyway) and the “charge” icon.
I have this display for a 20s LiFePO4 battery with the selected voltage as 60v. But since my battery operating voltage is 60v-66v the battery meter doesn’t do anything until the battery way below normal range.
You might try the 60v selection and see if it works better for your battery.
If you have lead acid then unplug the charger before turning on the bike so voltage can drop from 59v charge voltage to 52v.
Price
Call 9409137897
प्राइस कितने का है यह कहां से मिलेगा
Call 9409137897 for pricing and technical specifications
Hi bro....bike sidha ready mode me a rahi low breack or high disconnet he fir bhi ....or display me gear or speed show nahi ho raha he
Aapke controller me feature nai hoga
mere bike metre 25 ke hi speed dikhati hai25 electric bike
Call 9409137897 or 9409137849
I dont think so that any of the electrical have correct speedometer !!!
Adjustments and calibration are needed but companies never do it...
how to reset
You can reset it to zero kilometer using key switch .
8 times key switch turn om turn off .
@@InfiniteLaboratory thanx
one more thing is there any option to add exhaust sound in ebike
@@InfiniteLaboratory subscribed n liked for ur quick response
Speed double dikhata he
Use potentiometer
Sir no plz
Visit www.motorkit.in