Needs a full front end....Did I hear you say money pit? What do I mean by money pit...I mean Carli Unchained level build. As a poor, I do many things in the sun also, you could have greatly benefitted from one of the cheap pop up tent deals while doing the motor work in the sun. I used one while working on farm equipment one day.
I have used the liquid electrical tape. It works really well in tight spots where you can’t easily get heat shrink or actual electrical tape. But heat shrink tubing would have been my first choice on that ground wire. I love these videos, I’ve learned a lot over the years watching you.
I’m new to the Cummins trucks and more specifically the 2nd gen and your videos have helped me a lot and inspired me to try my own build! Thank you, great content!
Sam, those later 2nd gen gear cases have a raised collared hole for the KDP. They are factory KDP proof. If you look inside the hole where the dowel is you can see the raised edge just inside the hole. That fix is also why those covers aren’t flat right there like a 12V gear case is and if you did use a KDP kit to add some cheap insurance you’d have the step the washer to cover the hole and still use the 10 mil headed case bolt next to it. That all said, I still do just about exactly what you did and stake that hole funky with a center punch just for my own peace of mind.
Love watching your videos. Tried buying my grandpa’s 2nd gen from my grandma and wouldn’t sell it to me but last winter the snow load on the shop brought it down and one of the main steel beams came down right on the cab 😢. Turns out I could just have it now🤦♂️🤦♂️. Plan on fixing it so I’m glad I found you on RUclips. Keep on saving em.
I’m telling you,I really enjoy your videos,glad you’re saving the old girls.I’ve got a early 2007 3500 mega cab 4 wheel drive 5.9 bought it brand new still in mint condition 93,000 mile,wish I could get my hands on some of the old girls
The way frames are pulled at a bodyshop, they are over pulled and allowed to spring back into position. pulling and leaving tension does not really do anything unless you are heating it up.. Also i changed a ram front axle for this same bent reason, the upper "C" part of the axle gets pushed open/wider causing the camber to be off.
I need to find a used VP44 cheap that I can use as a core so can get a good remanufactured VP44 to as an spare. Mine is fine still I just want a spare before they become hard to get.
I put a stick/handel in the track of my rear window so it cant slide open w/out being removed from the inside! Guess ppl were more honest when they designed the rear windows!??!
When a drunk driver caused me to wreck at 75, the stock control arms completely folded. The axle snapped but the ranch style bumper is the only reason my truck was savable. If not it would have been toast
Why does it have CAD ? Hmm. The passenger rail on my '98 is tweaked from a wreck the PO had. 5/16 out of square but everything still fit with a bit of massaging. Aligns and drives straight. Wasn't worth messing with. I did ditch the factory axles for 01+. Muck better design and can use 3rd gen brakes and unit bearings.
Hey Sam, I really liked this episode. I like wreck repairs. I was thinking about your 66 Power Wagon. Why not hire a body guy to do some moonlighting and do the sanding for you in your shop. Pay him 50 bucks per hour under the table.
Cooked the ecm on mine. Having a computer mounted to the engine block isn’t the greatest idea. Someone needs to make a relocation kit for that or something.
I’ve got about 18 months before I start seriously looking into getting another 2nd gen. Bought an 02 six speed sport from my dad with 65k for $10k back in 2010. Like an idiot I got rid of it with 109k miles 🤦♂️. I’ll be in a place within the next few years where I’ll be searching with cash in hand. I’ll have to email you or something when that time comes. After the past few years watching your videos I refuse to go to anyone else. If you’ve had it or gone through it I know it’s a solid unit that I can do routine maintenance on a drive for years and years to come.
If I was you when I got ready to get rid of the truck id probably try to offer to sell or deal on it to the person that got it it stolen probably the only reason after trying to keep it in good shape he got rid of it is how bad it appeared to be wrecked and the interior got all busted up....
The worst vehicle anyone can buy now is one that has been drowned in a flood. Would be a nightmare to restore. Imagine the wiring headaches and computer problems.
This will be the time i will say to not fix this truck. I work in the body world and i have seen bad things. If you are going to keep the truck for you, cool, but if you plan to flip this truck should not be fixed and back on the roads. 2 bad things on this Vin, bad frame and theft recovery, great parts truck only, sorry, just my 2 thoughts. if you fix it and sell it and they insure it like they have too and then its in another accident their insurance will not pay to fix it, i see this all the time.
Needs a full front end....Did I hear you say money pit? What do I mean by money pit...I mean Carli Unchained level build.
As a poor, I do many things in the sun also, you could have greatly benefitted from one of the cheap pop up tent deals while doing the motor work in the sun. I used one while working on farm equipment one day.
I have used the liquid electrical tape. It works really well in tight spots where you can’t easily get heat shrink or actual electrical tape. But heat shrink tubing would have been my first choice on that ground wire. I love these videos, I’ve learned a lot over the years watching you.
Nice going Sam keep bringing them back to life ! Love watching
I’m new to the Cummins trucks and more specifically the 2nd gen and your videos have helped me a lot and inspired me to try my own build! Thank you, great content!
Sam, those later 2nd gen gear cases have a raised collared hole for the KDP. They are factory KDP proof. If you look inside the hole where the dowel is you can see the raised edge just inside the hole. That fix is also why those covers aren’t flat right there like a 12V gear case is and if you did use a KDP kit to add some cheap insurance you’d have the step the washer to cover the hole and still use the 10 mil headed case bolt next to it.
That all said, I still do just about exactly what you did and stake that hole funky with a center punch just for my own peace of mind.
Love watching your videos. Tried buying my grandpa’s 2nd gen from my grandma and wouldn’t sell it to me but last winter the snow load on the shop brought it down and one of the main steel beams came down right on the cab 😢. Turns out I could just have it now🤦♂️🤦♂️. Plan on fixing it so I’m glad I found you on RUclips. Keep on saving em.
Makes it even better now! Worth the work!
I also used a 98 2500 gasser axle to replace the one in my 3500 after the wreck. I did put new bearings which solved the dually adapter problem
I’m telling you,I really enjoy your videos,glad you’re saving the old girls.I’ve got a early 2007 3500 mega cab 4 wheel drive 5.9 bought it brand new still in mint condition 93,000 mile,wish I could get my hands on some of the old girls
Very nice project!!!! Id just build some long arms for it and forget those stock mounts. Looking good!!! KEEP IT UP
The best second gen content out there !!
Thank you
Check the IOD fuse for the no bus
Great video
Can’t wait to see you finish it up
Glad you saved it
The way frames are pulled at a bodyshop, they are over pulled and allowed to spring back into position. pulling and leaving tension does not really do anything unless you are heating it up.. Also i changed a ram front axle for this same bent reason, the upper "C" part of the axle gets pushed open/wider causing the camber to be off.
Yes that’s what I did to the frame
Nice man. Keep the truck content coming. Can’t wait for phase 2!
I need to find a used VP44 cheap that I can use as a core so can get a good remanufactured VP44 to as an spare. Mine is fine still I just want a spare before they become hard to get.
Thanks for sharing, keep the updates comin’!👍
I put a stick/handel in the track of my rear window so it cant slide open w/out being removed from the inside! Guess ppl were more honest when they designed the rear windows!??!
When a drunk driver caused me to wreck at 75, the stock control arms completely folded. The axle snapped but the ranch style bumper is the only reason my truck was savable. If not it would have been toast
Did the correct timing gear seal come in a common rail kit from Amazon too? Love your videos and info, THX!
No had it on the shelf from Napa
And thank you
Thx very much for the response!!@@VBELTandSON
Look identical to my beast I Wrecked in MI😢 mine looked worse but still gonna do something with it!
Ok mine was not that bad
Love the Cummins content
Yep Sam. That’s a rare color. I like it 👍🇺🇸💪🏻
Are those later style ram wheels. I like them
Why does it have CAD ? Hmm. The passenger rail on my '98 is tweaked from a wreck the PO had. 5/16 out of square but everything still fit with a bit of massaging. Aligns and drives straight. Wasn't worth messing with. I did ditch the factory axles for 01+. Muck better design and can use 3rd gen brakes and unit bearings.
?
Nice job as always bud 👍
Hey Sam, I really liked this episode. I like wreck repairs. I was thinking about your 66 Power Wagon. Why not hire a body guy to do some moonlighting and do the sanding for you in your shop. Pay him 50 bucks per hour under the table.
Not a bad idea. But the Body work is done. Just needs painted.
@@VBELTandSON even better
Good luck doing that with my cable operated fuel shut-off.
Cooked the ecm on mine. Having a computer mounted to the engine block isn’t the greatest idea. Someone needs to make a relocation kit for that or something.
Cool project!!👍🏽..Aloha 🤙🏽
I’ve got about 18 months before I start seriously looking into getting another 2nd gen. Bought an 02 six speed sport from my dad with 65k for $10k back in 2010. Like an idiot I got rid of it with 109k miles 🤦♂️. I’ll be in a place within the next few years where I’ll be searching with cash in hand. I’ll have to email you or something when that time comes. After the past few years watching your videos I refuse to go to anyone else. If you’ve had it or gone through it I know it’s a solid unit that I can do routine maintenance on a drive for years and years to come.
Where is the best place to find a dually bed
The other seal will be for a VE pump timing cover
Are you making a statement with that shirt?😊
Damn Sam do you know how many armchair mechanics. You sent into a mental breakdown by not torquing those bolts. 😂😂
I purposely deleted the next clip tightening them lol
🤣🤣🤣🤣
Man your so lucky you don’t have to work with rust lol I wish we had stuff that clean smh
Far From Stock long arms and drag links🤌🏽🤌🏽🤌🏽
Did you put a wear sleeve on the crank or was like new ?
Didn’t need one. She was good to go with new seal
That liquid electrical tape is the shit
Would you want to sell that front driver seat!!! I have a 2nd gen and my front driver seat blown out!!! Lol
Amazon new seat cushion and cover done desl
🤦🏻♂️🤦🏻♂️ probably should use my brain!! Thanks man!! Really love the channel! Saw you the other day and honked the horn and yelled V BELT & SONS!!
you need to heat the rails up before pulling
If I was you when I got ready to get rid of the truck id probably try to offer to sell or deal on it to the person that got it it stolen probably the only reason after trying to keep it in good shape he got rid of it is how bad it appeared to be wrecked and the interior got all busted up....
I fixed this truck for a friend it turned out to be one of the nicest second gens if not the nicest one I’ve ever driven.
I’ll take it
You selling?
The old Bilstein 5100s hehe
Love the shirt
The worst vehicle anyone can buy now is one that has been drowned in a flood. Would be a nightmare to restore.
Imagine the wiring headaches and computer problems.
Love IT Sam, Thanks. I would Love to onit Sam. Maybe some day. God Bless You SAM.
MAY GOD LOVE BE WITH YALL .
GOD BLESS YALE
Lot of money to fix this one bro
They all aren’t cheap to fix
Heard that
🤞🏻
😂
This will be the time i will say to not fix this truck. I work in the body world and i have seen bad things. If you are going to keep the truck for you, cool, but if you plan to flip this truck should not be fixed and back on the roads. 2 bad things on this Vin, bad frame and theft recovery, great parts truck only, sorry, just my 2 thoughts. if you fix it and sell it and they insure it like they have too and then its in another accident their insurance will not pay to fix it, i see this all the time.
Footage is old truck is on to its new life;)
Looks hideous with the 5th gen wheels on it. Needs to go back down to 17's.
I’m more concerned with how wrecked it is