CHonda Clone Engine Spark, Fuel, but Won't Start
HTML-код
- Опубликовано: 10 дек 2021
- amzn.to/3IBUm1L Starter Fluid
amzn.to/3yhliPs Spark plug removal tool 5/8"
amzn.to/3ydPATe Compression Tester OTC
amzn.to/31RQOYj Spark plug boot removal pliers
amzn.to/30mx66A Echo Spark Tester PET4000
amzn.to/31OuUoG ThruNite Head lamp rechargeable
amzn.to/3lV1w7x Briggs Spark plugs for CHonda Clones
amzn.to/3oMSevS Feeler gauge Set
In this video, I troubleshoot a Cub Cadet Leaf Blower that won't start.
Help support Doublewide6 Repairs LLC by sponsoring his Patreon Account
/ doublewide6
Doublewide6 Repairs LLC has a Master’s Degree in industrial technology with a specialization in Manufacturing, due to factors beyond the control of Doublewide6 Repairs LLC and anyone featured in his videos, I cannot guarantee against improper use or unauthorized modifications of this information. Doublewide6 Repairs LLC assumes no liability for property damage or injury incurred as a result of any of the information contained in this video or any of Doublewide6’ Repairs LLC's videos. Use this information at your own risk. Doublewide6 Repairs LLC recommends safe practices when working on equipment, power tools, chemicals, electronics, electrical systems, vehicles, and or with tools seen or implied in this video. Due to factors beyond the control of Doublewide6 Repairs LLC, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Doublewide6 Repairs LLC. Развлечения
amzn.to/3IBUm1L Starter Fluid
amzn.to/3yhliPs Spark plug removal tool 5/8"
amzn.to/3ydPATe Compression Tester OTC
amzn.to/31RQOYj Spark plug boot removal pliers
amzn.to/30mx66A Echo Spark Tester PET4000
amzn.to/31OuUoG ThruNite Head lamp rechargeable
amzn.to/3lV1w7x Briggs Spark plugs for CHonda Clones
amzn.to/3oMSevS Feeler gauge Set
That head light just reminded me that I have one and haven't been using it.
That engine being a Honda clone, I am impressed that the engineers used a valve cover gasket vs. gasket sealer. I have dreaded adjusting valves on Honda engines in the past because I end up spending 15 minutes doing the adjusting and an hour tediously scraping the old sealer from surfaces. Thus, I have been cutting my own gaskets from basic Felpro 3157 gasket material & so far, no leaks. I made a cardboard template so I can outline the correct shape on the gasket material quickly & usually cut out several at a time. A cheap set of hole punches from Harbor Freight includes the perfect-sized punch for the screw mounting holes.
Perfect diagnosis process to find the valve problem. Great job. Thanks for the video and the tips.
I got lead down a different path, originally I thought is was a coil / low spark issue. Thanks
Great job on the diagnoses and fix Bob. Thanks for the tips pn the spark plug wrench and the plug for these engines. Hope everyone is doing well. Merry Christmas to you and the family!!
Glad to help. Wishes you the best. Happy Holidays.
Good fix man, a lot of people don't think to check the valve lash. I bought a honda shelf propelled mower and someone gave me an almost new pressure washer and all I had to do was just the valves.
Those are the best ones to get. nice score.
Good trouble shooting - valve gap - adjustment is typically overlooked by rookies like me. I was surprised to hear about the past experiences with some of the NGK plugs - I've always found them to be the most reliable - especially in the Stihl 2 cycle equipment. Thanks for the video.
It is very rare, but I have seen low spark and no spark with them.
There are counterfit parts also on ebay and Amazon
Great fix sounds better !
Love the lift table
Nice job and video Bob, I really like your lift table.
I like it I am going to be making a video of all the mods that I have done to it. Just finished up new ramps on it video coming soon.
Nice brother, looking forward to it sir 👍🏼🙂
Nicely done Bob
Thanks for watching and commenting. Bob
Did you check the compression after the adjustment? Am surprised it did not fire at all at 70psi. Thanks for the video.
No I did not check it, I am going to run it for about 1/2 an hour see how it does then I will take a reading.
Good job, I saw the look on your face when you looked in the tank and it was empty. Been there.
Just ask Carl Childers!
Good idea!!
good info good job!!!! i am in nova scotia
Very cool! Thanks for watching.
Nice presentation.
..👍 # 158
Stay well, Joe Z
Thank you, those are good tips. I usually just add to the old rtv if it comes off smooth. I use the Right Stuff. It is not the best way to do it but it is fast and cost effective.
It is very common for the mags to go bad on these- I have changed many
Couldn't you use a spark plug socket and an extension instead of the tool you've got there? Thanks for the video.
I just did a head gasket on one of these engines on a craftsman single stage snow blower.
I have only done one head gasket on these engines. In fact, the issue was a bent valve, not the gasket but I replaced both.
Nice video Bob we have had a few engines come in with valve clearances too small but these were older engines where believe the valves had beaten in for the clearance to get smaller than the original factory setting. This unit appears too new for that to happen what do you think? The OLD MAN at EP over and out!
It was a landscapers, so it has many hours also the Chinese steel is not a hard as US steel. I don't think the adjustment slipped because those things were as tight as they get. I will send an email about stickers. Bob
Those chonda engines could be good sometimes and bad this one was bad needed some work to get it going again usually those ngk plugs are really good but maybe a bad batch of them made at that time
Who can I get predictor H F engine coil from ?????
With 70 psi compression at the start as it was, you definitely should have the engine at least puffing or trying to start a little. The original spark plug was probably just flooded.
That is a good tip that I overlooked. I was playing with it for about five minutes the night before and thought it was a low spark issue because the spark was yellow. When I changed the plug it looked better. I hear the magnet on the flywheel is known to go bad, too.
@@doublewide6 I always use a proper spark plug tester with an enlarged gap for testing if spark strength. Spark color is very subjective and difficult to observe right. When I do have weak spark, it will often only intermittently jump the spark tester as I turn it over.
I just fixed my neighbour's almost new powermore snowblower engine. Torch plug was bad.
I bought a new snow blower China model the darn thing took for ever to start it has electric start.. This fall i messed with it because it would take five minutes to start I changed the plug to a decent plug now it starts with the pull rope.. those torch plugs are junk even if you are getting spark from one they are junk for some reason they don't work well.. my opinion only
Whenever I see an E3 plug I change it out because they don't work.
very common for mags to go bad on these
I have not had any in the shop with the bad magnet but I will keep it in mind thanks for the tip.
Aren't those called LCT engines? lmk.
I was thinking that when I was editing the video LCT LTC Chinese. They are called many different things.
He fills his machine with gasoline and cleans it at the same time lol
Ahh wish we all were perfect, but I'm not, I did spill some gas thanks for taking the time to point that out.
@@doublewide6 I was kidding, though it was funny, no need to be a douche about it. Yes, we all do and have done it, so wasn't trying to say your were "imperfect".
I love me some dw6 but i think he's really hurting for a video when he has a 20 minute "how to add gas to a small engine video"
I usually just shoot a bit of carb cleaner in the spark plug hole once I have spark. Idle circuits are common causes of no start. Of course there's always Carl Childers to think about
If it has a cheap spark plug just change it ASAP
They are junk