Those are AWESOME!! I built my triple monitor stand two months ago and spent days trying to get them lined up nicely. They're close but pot perfect. I knew someone had to make something like this. this is my next equipment purchase.
When I was planning on finally upgrading to an aluminum profile rig these were included in the material list. My sole reason for going to a profile rig was monitor alignment. Can't wait to get it all set up and have perfect alignment. Thanks, Shaun, for highlighting this product.😁
This is a product that was needed for a long time! I had that same issue with a previous triple setup where the bottom of the monitor had the larger lip that stuck out. I took a file and smoothed off the edges so and they lined up perfectly.
10 years ago when I was running triple monitors I pulled the plastic housing off them all and just had the raw lcd screen so I could push them together even closer. It went from around 20mm to 5mm.
@@S2GUnit Nah. The plastic housing is mostly just for show. The monitor buttons were connected to the panel with a ribbon cable from the panel so they needed to be managed. But everything else was mounted to the panel. Inputs. Power supply. The plastic was just for show.
Great video as always buddy 👍 My monitor mount is 40x40 with triple 32" curved monitors. The thing is, with both sides of the center monitor curving outward, I had to use spacers to push the left and right monitors out a bit for the bezels to line up with the center monitor. Aligning curved monitors is definitely a bit trickier than aligning flat monitors. I'll probably have to get these monitor mounts at some point. BTW, you can use a sanding block with fine grit sandpaper to sand a slight angle on both sides of the lower lip of the center monitor and the corresponding sides of the outer monitors in order to get perfect alignment without any issues.
I own a simlab triple stand and never had an issue with gettimg my tripples perfect. With a square level monitor stand and square monitors the only feature I see being usefull is the tilt. We have similar monitors and I ended up trimming the lower bezels on the right and left monitors to get the side angles I wanted. When are we going to see a hybrid curved center with flat side triple setup? 👍👊
Можно выдвинуть средний экран вперёд, так чтобы чёрные рамки боковых мониторов зашли за рамку центрального монитора. Тогда чёрные полосы между экранами будут в два раза меньше.
Wish i could do this im in alcove wifh triple monitors say on desk. Its not perfect but i only play ETS2 & ATS 2 monitors are perfect jyst the right one which is a little misaligned
Is the Trak Racer triple monitor mount with 800mm center profile big enough to get good usable angles with 32 inch monitors?? I've read some comments suggesting I should have gone for a bigger center profile for easier adjustment. I have some Vario kits on order as well.
I just recently subscribed to your channel and have enjoyed the content (I need a Simagic Neo). What size monitors are you using? I definitely want to go to triples somewhere down the line.
I have the Sim Lab ones and these look far easier to adjust. Sim lab are just bolts with an allen key head on the end where these have the knobs that look much easier to access. The ones to move the monitor left or right on the Sim Lab mount are hard to get to and use a much smaller allen key than the rest. They also only have one bolt on the bottom to adjust the vertical tilt where these have 2, and it looks like you can use those to also fine tune the angle if I understood right.
Those are AWESOME!! I built my triple monitor stand two months ago and spent days trying to get them lined up nicely. They're close but pot perfect. I knew someone had to make something like this. this is my next equipment purchase.
When I was planning on finally upgrading to an aluminum profile rig these were included in the material list. My sole reason for going to a profile rig was monitor alignment. Can't wait to get it all set up and have perfect alignment. Thanks, Shaun, for highlighting this product.😁
Appreciate the video mate. Trying to setup my 32" triples using the standard NLR vesa mounts is giving me permanent brain damage.
This is a product that was needed for a long time! I had that same issue with a previous triple setup where the bottom of the monitor had the larger lip that stuck out. I took a file and smoothed off the edges so and they lined up perfectly.
10 years ago when I was running triple monitors I pulled the plastic housing off them all and just had the raw lcd screen so I could push them together even closer. It went from around 20mm to 5mm.
Did you ever have any issues with the LCD panels being so fragile?
@@S2GUnit Nah. The plastic housing is mostly just for show. The monitor buttons were connected to the panel with a ribbon cable from the panel so they needed to be managed. But everything else was mounted to the panel. Inputs. Power supply. The plastic was just for show.
All triple screen mount should come with adjustable adapters
great video mate. will be purchasing these for my NLR elite stand alone triple monitor stand to get the perfect alignment :) thank you very much
Trakracer is a local to me company. Great company and products.
Great video as always buddy 👍 My monitor mount is 40x40 with triple 32" curved monitors. The thing is, with both sides of the center monitor curving outward, I had to use spacers to push the left and right monitors out a bit for the bezels to line up with the center monitor. Aligning curved monitors is definitely a bit trickier than aligning flat monitors. I'll probably have to get these monitor mounts at some point.
BTW, you can use a sanding block with fine grit sandpaper to sand a slight angle on both sides of the lower lip of the center monitor and the corresponding sides of the outer monitors in order to get perfect alignment without any issues.
I own a simlab triple stand and never had an issue with gettimg my tripples perfect. With a square level monitor stand and square monitors the only feature I see being usefull is the tilt. We have similar monitors and I ended up trimming the lower bezels on the right and left monitors to get the side angles I wanted. When are we going to see a hybrid curved center with flat side triple setup? 👍👊
Можно выдвинуть средний экран вперёд, так чтобы чёрные рамки боковых мониторов зашли за рамку центрального монитора. Тогда чёрные полосы между экранами будут в два раза меньше.
I have a triple stand on the way. 6 Sigma Racing threw in some version of this kind of adapter in for free. Hopefully it helps.
Man I got this mount I have curved monitor and I’m having a hard time trying to get this close 32 inch
Wish i could do this im in alcove wifh triple monitors say on desk. Its not perfect but i only play ETS2 & ATS 2 monitors are perfect jyst the right one which is a little misaligned
Is this a samsung oddysey monitor you’re using?
Is the Trak Racer triple monitor mount with 800mm center profile big enough to get good usable angles with 32 inch monitors?? I've read some comments suggesting I should have gone for a bigger center profile for easier adjustment. I have some Vario kits on order as well.
it should be ok with 32 inch monitors. you might be at the limit of the length. Any monitor bigger than 32, you will need the 1800mm size
I just recently subscribed to your channel and have enjoyed the content (I need a Simagic Neo). What size monitors are you using? I definitely want to go to triples somewhere down the line.
I am currently on 27 inch monitors. Id like to upgrade but these are pretty good 144 hrtz monitors. So I am happy enough for now.
Thank you!
How do these compare to Sim Labs version which always seems to be out of stock?
They are both great. Ameer has the Simlab version and now I have this one and both do a great job at aligning through monitors
I have the Sim Lab ones and these look far easier to adjust. Sim lab are just bolts with an allen key head on the end where these have the knobs that look much easier to access. The ones to move the monitor left or right on the Sim Lab mount are hard to get to and use a much smaller allen key than the rest. They also only have one bolt on the bottom to adjust the vertical tilt where these have 2, and it looks like you can use those to also fine tune the angle if I understood right.
Murder Ram approves this video.
...or just get a quest 3.