Great video! I had been looking for a video that explains how to set up this temp controller exactly how you set this up. You even explained the circuit board and components. This video does it beautifully. Thank you for explaining how this works!
Great advice, Bob. Thanks for the speedy and insightful reply. I plan to incorporate all of your suggestions when I take this new approach next spring. Looking forward to catching you in the store someday so I can shake your hand. My wife has kin in Gainesville and so we pass fairly close once in a while.
Great video man! This is a very interesting and specific videos! I’m inspired by your high quality videos and your channel! I watched your video all the way through!
hi sir.. i found your videos more detailed.. if i use it in ref to maintain the temperature for 17-15 degrees.. it will not break my refrigerator if i just plug it and play
Great video, thanks for the explainer. Quick question. I noticed that the device has 22awg wire for those connections. It seems like that is undersized for 1500w. Have you load tested at the design limit?
Hello sir, I have a cloth dryer. The heater is rated at 220v, 1500w. I usually use the dryer for a period of 3-4 hours at a time. Would you recommend using this thermostat controller for this kind of application? I appreciate your opinion on this. One more question, does the min max value set holds if we switch it off? Thank you
Does the initial temperature setting keep the same after the power supply shuts off and then turn on again? I am trying to use it to control my condenser to run during the low temperature in winter. Thanks
My question is in regards to the extrension you use, im your video you use a single extension My question is, could i use a double extension for 2 heat mats or will it over load the w3001?
So this doesn’t need a adapter? This can be directly soldered onto a regular plug? Can you maybe show us your whole set up ? Such as your plugs and how everything was put together . I can’t find a single person that has showed the whole process showing everything
@@robojax great video!!! It answered all my questions. That day I watched soo many videos that didn’t answer my questions so I just started to skip through other videos but I’m glad I watched this! Great video and thank you for sharing your knowledge!
What is the max power output. I have 4 heating elements. Small ones for soldering but won't heat all 4. A couple sure so thinking I must have maxed out the capability of the unit.
@@robojax you did. And very clear. Just trying to figure why it would work 2 but hook up any more and nothing. No worries. I'll figure it out. Thanks though. 1200w. With 10 amp in a 120 walloutlet. Just so you know. I was listening. Not being lazy. And just writing to get answers. Have a good day
If my extension cord has a ground wire, can that be used to wire this up? If so, does the ground wire just bypass this unit while the live and neutral go into and out of it?
This is just a switch to connect and disconnect two wires. You have to use it in a safe way. Ground has nothing to do with this. Keep the ground , wire it such that it can turn on and off your device
Thanks Ahmad for your review of this temp controller. I need a temp controller one for my chicken egg incubator. Could you recommend which one would have the best tight temp control of those you've tested? I'd hope to control the temp to swing within 37.5 and 37.8 degrees centigrade. Thanks for all your reviews and time. Greg from Smartsville, Calif.
You are welcome Greg. I have reviewed so many. All of them work well. some are for DC some on AC some also have humidity sensor. Here is a link that show some of them ruclips.net/channel/UCkcBSig_Iu4ZnAIeCeG1TVgsearch?query=temperature+AC
you have so many "what". it is as if we say "what if your email goes to the wrong person". the reading will make sense. if you are in room with a shirt and comfortable, then you should know it is about 22 or 23 °C. If I mentioned to press both buttons, then that is the result (I don't it now as I have done 100s of more videos) and if not, then do not press both keys.
Hello, I mentioned at the beginning that you can control AC or DC load. Load means fan, heater, TV or anything. just make sure do not go above the rated load of relay. Visit resources for this video: robojax.com/L/?id=252 and in your module see what is written on the relay. if is it 10A, connect only 10A load.
Hello, Thanks for video. Is this device have a calibration factor? For example, the real room temperature 24 but device shows 25. Can we calibrate it ? Thanks.
my friend. I have explained the rating of relay in terms of Watt. so your load or mat should have power written on it. like 10W or 800W. it will turn it ON and OFF it is not buoyed the limit. if it is , it will cause fire.
Hi.Thank you very much for all the information. I want to build a chicken incubator. The heating element is a 100 watt light bulb. Do I need a solid-state relay or it is enough with the setup you just show in this video? Thank you very much.
Will the thermostat be damaged if you connect the AC phase to the black wire? I am asking because in some European countries the plug is reversible, and the phase can be either on the left or on the right, in the electrical socket it is not marked.
what? didn't you watch? this is just a switch to turn ON or OFF. Whatever the votage of your load is. Please watch. your questions says, you did not watch and asked.
I just watched the video and it has been explained. So please watch it without skipping. you just searched the model on Amazon, eBay or aliExpress to get it.
What tone? I have explained and shown how to calculate. It is I just the rating of relay. First know the power of your device . If voltage is 220V and power of load is 1000W then find the current 1000W ÷220=4.5A . Watch the video and don’t skip. If you watch it fully , you will not have any questions left.
Bonjour, Ceci est le contrôleur de température et la gamme qu'il convient d'utiliser pour l'incubateur. Cela n'a pas d'humidité si votre incubateur a besoin d'un contrôleur d'humidité. J'ai une autre vidéo qui montre un module qui a également un régulateur d'humidité. Merci de ne pas sauter les publicités et de continuer à les regarder. Cela m'aidera beaucoup.
@@robojax Bonjour, ok mais la puissance de 150 Watt de la résistance que j'ai pour ma couveuse conviendra quand même à ce thermo controler XH-W3001? à vrai dire je n'ai pas besoin que le taux d'humidité soi contrôlé car c'est géré par un autre système. Ce qui me préoccupe plus c'est l'adéquation controler et résistance?
Ce module que vous essayez d'utiliser possède un relais. J'ai expliqué le classement des relais ici dans cette vidéo ruclips.net/video/a8yJoeFsKWw/видео.html
My Thermostat is measuring impossibly high temperatures (such as 51.5°C) when my thermometer is measuring room temperature. It also doesn't switch my heating pad off (I'm using it for a reptile cage) when it goes above my stop temperature. I've tried using both its heating and cooling function and neither works correctly. When the black cable (with the probe on the end) gets near the box, it goes crazy and random temperatures start flashing up on the screen and it makes a clicking sound. Could you please help?
@@robojax As it turns out, I simply didn't program it correctly, but it works now (however bringing the black cable near the box still causes it to go crazy). To program it I had to press the up and down buttons simultaneously for more than three seconds (if it displays 888 all is good, LLL means the sensor is at fault, HHH means the temperature is above range) After that, I simply followed the instructions in this video. Thank you for the help! (I used the third image by this link as a reference - ultimateexotics.co.za/product/temperature-controller-basic/)
Perhaps my subscribers don't care about this product. However this is very famous product and soon non-subscribers will find it and we will see how they like it.
Great video! I had been looking for a video that explains how to set up this temp controller exactly how you set this up. You even explained the circuit board and components. This video does it beautifully. Thank you for explaining how this works!
Great advice, Bob. Thanks for the speedy and insightful reply. I plan to incorporate all of your suggestions when I take this new approach next spring. Looking forward to catching you in the store someday so I can shake your hand. My wife has kin in Gainesville and so we pass fairly close once in a while.
4:08 thanks man. Just what I needed.
Great video man! This is a very interesting and specific videos! I’m inspired by your high quality videos and your channel! I watched your video all the way through!
I am pleased that you liked them. Thank you for watching.
Thank you. A great help.
You're welcome!
Xcellent video, answered all my questions... thanks
You are welcome.
hi sir.. i found your videos more detailed.. if i use it in ref to maintain the temperature for 17-15 degrees.. it will not break my refrigerator if i just plug it and play
Excellent explained
très bien filmé....très bien expliqué..........simple et pro............thank you
you are welcome.
THANK YOU MISTER FOR YOUR VIDEOS !BUT WHAT ARE THE CARACTERISTICS OF THE CONDENSATORS OF THE XH-W3001
Very good review
Very helpful. Thank you.
Excellent explanation! You really helped me! Thank you!
you are welcome. The best "Thank you" for me is to subscribe to my channel. Thank you
Great video, thanks for the explainer. Quick question. I noticed that the device has 22awg wire for those connections. It seems like that is undersized for 1500w. Have you load tested at the design limit?
whatever tests I have done is shown in this video. Contact the seller or manufacturer in regards to the quality of wires.
Hello sir, I have a cloth dryer. The heater is rated at 220v, 1500w. I usually use the dryer for a period of 3-4 hours at a time. Would you recommend using this thermostat controller for this kind of application? I appreciate your opinion on this. One more question, does the min max value set holds if we switch it off? Thank you
Already used. Works perfectly
How can i get this and other equipment of connection for hatching accompany with this item
Does the initial temperature setting keep the same after the power supply shuts off and then turn on again? I am trying to use it to control my condenser to run during the low temperature in winter. Thanks
Yes it keeps it.
Hi. Where the Yellow and black wires are could i add a double socket to it? or does it have to be a single? Its to run 2 heat mats. Cheers
Hi, you made me watch the video . I have practically explained and shown how to use it. what else do you want? I did not understand.
My question is in regards to the extrension you use, im your video you use a single extension My question is, could i use a double extension for 2 heat mats or will it over load the w3001?
Thank you. Can you use this to control water heater (geyser)?
This is just a witch and it can turn in off anything
So this doesn’t need a adapter? This can be directly soldered onto a regular plug? Can you maybe show us your whole set up ? Such as your plugs and how everything was put together . I can’t find a single person that has showed the whole process showing everything
Perhaps you skipped the video. the whole purpose of this video was to teach you that. Please watch and you will get answer to all of your questions.
@@robojax great video!!! It answered all my questions. That day I watched soo many videos that didn’t answer my questions so I just started to skip through other videos but I’m glad I watched this! Great video and thank you for sharing your knowledge!
What is the max power output. I have 4 heating elements. Small ones for soldering but won't heat all 4. A couple sure so thinking I must have maxed out the capability of the unit.
I believe I mentioned the power handling value.
@@robojax you did. And very clear. Just trying to figure why it would work 2 but hook up any more and nothing. No worries. I'll figure it out. Thanks though. 1200w. With 10 amp in a 120 walloutlet. Just so you know. I was listening. Not being lazy. And just writing to get answers. Have a good day
Beautiful ❤️
If my extension cord has a ground wire, can that be used to wire this up? If so, does the ground wire just bypass this unit while the live and neutral go into and out of it?
This is just a switch to connect and disconnect two wires. You have to use it in a safe way. Ground has nothing to do with this. Keep the ground , wire it such that it can turn on and off your device
Thanks Ahmad for your review of this temp controller. I need a temp controller one for my chicken egg incubator. Could you recommend which one would have the best tight temp control of those you've tested? I'd hope to control the temp to swing within 37.5 and 37.8 degrees centigrade. Thanks for all your reviews and time. Greg from Smartsville, Calif.
You are welcome Greg. I have reviewed so many. All of them work well. some are for DC some on AC some also have humidity sensor. Here is a link that show some of them ruclips.net/channel/UCkcBSig_Iu4ZnAIeCeG1TVgsearch?query=temperature+AC
hello, what if the room temperature read is incorrect . what is the digit given when pressing both buttons at the same time? thanks
you have so many "what". it is as if we say "what if your email goes to the wrong person". the reading will make sense. if you are in room with a shirt and comfortable, then you should know it is about 22 or 23 °C. If I mentioned to press both buttons, then that is the result (I don't it now as I have done 100s of more videos) and if not, then do not press both keys.
Can I get/buy the 110v with Fahrenheit instead of Celsius ? If so, where ?
search on eBay, Amazon or Aliexpress. Or very simple, build your own ruclips.net/video/yJYXfaU9J34/видео.html
Hello. Maybe it's a stupid question, but can I connect a 300w electric Heather for the output instead of light bulb?
Hello, I mentioned at the beginning that you can control AC or DC load. Load means fan, heater, TV or anything. just make sure do not go above the rated load of relay. Visit resources for this video: robojax.com/L/?id=252 and in your module see what is written on the relay. if is it 10A, connect only 10A load.
@@robojax thanks for the quick replay!
you are welcome.
Hello, Thanks for video. Is this device have a calibration factor? For example, the real room temperature 24 but device shows 25. Can we calibrate it ?
Thanks.
Hello, if it can such thing, I have shown it. I don't remember unless I watch it. So you watch it fully and see if it has or not.
@@robojax hello, thanks for prompt reply, I watch the full video but couldnt see that you mention. So it doesn’t have it?
If you didn’t see it then it does not have it. I have so many videos of thermostats, check my channel.
Can we use this for 3KW heater??
I have shown the calculation. Do the calculation, find the current (ampere) = P÷V, P=power and V=voltage. I should not write it gain.
Hi
dear friend my I ask where can I order this thermostat please
Thanks
Hi, We don't sell it. you can get it from Amazon, eBay or AliExpress.
Could this be used for a reptile heat mat?
my friend. I have explained the rating of relay in terms of Watt. so your load or mat should have power written on it. like 10W or 800W. it will turn it ON and OFF it is not buoyed the limit. if it is , it will cause fire.
Hi.Thank you very much for all the information. I want to build a chicken incubator. The heating element is a 100 watt light bulb. Do I need a solid-state relay or it is enough with the setup you just show in this video? Thank you very much.
you are welcome. this is always better because it has relay.
@@robojax Thank you. So if I buy this thermostat I also need to buy a relay. Right?
@@BlueLineofthesky I don't think so. The 220v model has a 1500w rating.
I bought this hoping it's 12v, but I received one marked 24v? Obviously I can't use that with 220V but can I use it with 12v? Thanks
no. it will work only with 24V.
Will the thermostat be damaged if you connect the AC phase to the black wire? I am asking because in some European countries the plug is reversible, and the phase can be either on the left or on the right, in the electrical socket it is not marked.
no damage. it is just for safety.
Perfetto funzionamento se si riesce a programmarlo
Thank u so much sir
Hi can you use this to power an AC appliance? Thanks
Have you watched the video? What did I show you? Please watch if you haven’t to get the answer
@@robojax You said there was an AC to DC converter so it confused me.
I don’t voice I have talked about converter. 😂😂
@@robojax Lol dude you got the worst attitude how you talk to people. You absolutely said it.
Can it control 200 degree celcius temperature???? Please answer
It has been shown I the video. Please watch
Why the output is 24volts? What kind of bulb you use?
you did not mention the time. This just use relay to turn ON/OFF something does not mater. I used a bulb to demonstrate it.
CAn we use it as a timer switch also?
CAn we on and off a bulb if I want to work on day/light cycle?
Plz guide
Am a biochemist have no idea
This is NOT a timer. I have times of this things. This is thermostat meaning it works with temperature. Search my channel
You did not reply!
Sir mujhe high temperature pe supply start karna hai ,low temp pe supply off rahe.example 45℃pe fan start ho or 40 pe off .kya ye kam karega?
?
MY THERMOSTAT XH-W3001 is switching on and off after setting the starting temperature and ending temperature. Need your help pls
me be ON and OFF are too close. Set values apart.
Didnt get you pls
@@robojax
Thankyou 👍
Nice explained
thanks.
What's the output voltage?
what? didn't you watch? this is just a switch to turn ON or OFF. Whatever the votage of your load is. Please watch. your questions says, you did not watch and asked.
Hi,
There is no Need to correct the power ? How much is in Canada?
I just watched the video and it has been explained. So please watch it without skipping. you just searched the model on Amazon, eBay or aliExpress to get it.
Robojax Thanks you!
Will it hold the values when turned off?
I believe I've mentioned that. Yes it holds it. Perhaps I missed that to say.
Sir -degree per bhi kam karega
English or Farsi please.
Thanks man! I thought I broke it, but I just had the high and low reversed so it didn't heat lol
You are welcome. Good lock and Happy New year.
Is this product durable for longer use?
you would have to use it to know.
Do you have 110 vol out too?
no. the AC is to turn this device ON. it seems you haven't watched the video.
What if we accidentally put the wall plug the other way? Interchange live and ground.
it will function without any issue. expect it will be not safe to touch the output wires.
Please make a video of load testing 1500watt 30A boost step up converter.
I will make the video if get the module. Sure.
can this take on a 1.5/2 tone AC?
What tone? I have explained and shown how to calculate. It is I just the rating of relay. First know the power of your device . If voltage is 220V and power of load is 1000W then find the current 1000W ÷220=4.5A . Watch the video and don’t skip. If you watch it fully , you will not have any questions left.
@@robojax thank you for replying. I just wanted to know if I can install this device for and air conditioner.
Okay check the power and do the math.
Sir stc 1000 and w3001 which controller is best
I make the video so you watch and see which one is good for application.
@@robojax give me your video link
Bonjour,
Est ce que je peux utiliser ce thermostat pour une résistance de couveuse de 150W?
Merci pour votre réponse en Français si vous pouvez.
Bonjour, Ceci est le contrôleur de température et la gamme qu'il convient d'utiliser pour l'incubateur. Cela n'a pas d'humidité si votre incubateur a besoin d'un contrôleur d'humidité. J'ai une autre vidéo qui montre un module qui a également un régulateur d'humidité. Merci de ne pas sauter les publicités et de continuer à les regarder. Cela m'aidera beaucoup.
@@robojax Bonjour, ok mais la puissance de 150 Watt de la résistance que j'ai pour ma couveuse conviendra quand même à ce thermo controler XH-W3001? à vrai dire je n'ai pas besoin que le taux d'humidité soi contrôlé car c'est géré par un autre système. Ce qui me préoccupe plus c'est l'adéquation controler et résistance?
Ce module que vous essayez d'utiliser possède un relais. J'ai expliqué le classement des relais ici dans cette vidéo ruclips.net/video/a8yJoeFsKWw/видео.html
My Thermostat is measuring impossibly high temperatures (such as 51.5°C) when my thermometer is measuring room temperature. It also doesn't switch my heating pad off (I'm using it for a reptile cage) when it goes above my stop temperature. I've tried using both its heating and cooling function and neither works correctly.
When the black cable (with the probe on the end) gets near the box, it goes crazy and random temperatures start flashing up on the screen and it makes a clicking sound.
Could you please help?
Hello, I've not experienced such thing, I believe this module has defective.
@@robojax As it turns out, I simply didn't program it correctly, but it works now (however bringing the black cable near the box still causes it to go crazy).
To program it I had to press the up and down buttons simultaneously for more than three seconds (if it displays 888 all is good, LLL means the sensor is at fault, HHH means the temperature is above range)
After that, I simply followed the instructions in this video. Thank you for the help!
(I used the third image by this link as a reference - ultimateexotics.co.za/product/temperature-controller-basic/)
Memory wihout 230v?
“Does it hold settings when power is OFF?” Yes it holds settings.
my controller display is not working
if pressing any button does not wake it up. I assumed you watched the video. then buy another one.
magkano kaya electric consumption nya?
Farsi or English
W3001 Temperature Controller Balp does not burn what
did you mean "bulb"? and I did not understand what burns what? bulb does not burn W3001 and the w3001 does not burn the bulb.
Why there is 8 likes?????
Perhaps my subscribers don't care about this product. However this is very famous product and soon non-subscribers will find it and we will see how they like it.
First
Thanks.
Robojax can you do a new model bluetooth arduino car?
A full car is complicated project and needs multiple videos. I have it on my list. Will make video in the future.
@@robojax thank you so much
you are welcome.
говорил бы ты по-русски то цены б не было..
Я включил русские субтитры. просто прочтите по русски.