Very professional and simple teaching pace that enable every airgun user to understand the bits and pieces of their gun and understand how things work. Thanks Ernest and please convey my appreciation to the whole FX team.
Hi Ernest, Great video as always very informative, my question is I have the later MK3 with the brass bodied amp reg where you can remove the reg without stripping the whole of the reciever to to access it, is it possible to fit an in reciever reg such as a Huma to get a double reg set up same as the bt version the Maverick and the Impact ?
Mine wont latch when cocking. Ill have to check for the 33mm and the factory grub screw marks. Maybe thats all it is. In 22 caliber its my favorite gun. Insanely accurate and quiet.
I am having trouble with getting the sear back in correctly. The view of your video was not close enough, so I am a little bummed out. I will try and watch a couple more times. There are the 3 pin holes, to pin the sear, the pac-man assembly, and I believe you said a safety lock? Starting with the receiver upside down, the top hole #1-??, middle hole-??, and the bottom hole #3-??. I’m sure I am over thinking it. I know I should have recorded the takedown, that’s on my dumbass. Great video and I love my Cat III, but at this moment I can’t use it! 😭😭
Hello I have a new rifle FX Wildcat MK3 BT Compact cal.22 For cleaning reasons, I removed the barrel from the rifle by COMPLETELY unscrewing the two screws fixing the barrel of the rifle. On the official FX Airguns drawing, those two screws have references FX19086 (conical grub screw M6x8) and FX19955 (grub screw M8x6). The FX19955 screw (grub screw M8x6) had some dried glue around it: I cleaned this dried glue completely. I then reassembled the gun barrel and screwed the FX19086 (conical grub screw M6x8) and FX19955 (grub screw M8x6) screws. Since then, every time I fire, the air under pressure escapes from the screw FX19955 (grub screw M8x6). Should I put glue around this screw to avoid leakage? If so, which one? Could you help me Vincent (from Belgium)
In the disassembly video you said to make sure the valve screw on top of the receiver only had a half turn on it. Is that literally, or did you mean to back it out half a turn?
Hi I have a question how do you adjust the length of the barrel placement in the block? I just got a wildcat mk3 sniper .30 and the brass sleeve over the barrel at the block is out to far and will not let the clip slide in. It's safe to shoot, had to hand load it to set it.
I have a .25 wildcat mk3 sniper the stock settings are 110 bar reg and on power stand 7 it shoots the 25.4 grain jsb at 277ms 63 joules 69 shots before refill. I use power 5 245ms 49 joules 115 shots very nice gun.
Just received my wildcat mk3, something is loose and sliding back n forth near the power wheel.. any ideas? Is this normal? I have no idea, but seems like it should not have anything rattling .
If so please contact our technician team for more detailed assistance. FX Airguns United States Monday - Thursday 9 AM - 4 PM EST Fridays 9 AM - 3 PM EST Phone: +1 866 639 0772 serviceusa@fxairguns.com If not you can E-mail Sweden customer service at Info@fxairguns.com
@@FXAirguns spoke to us tech support, when not cocked the free float hammer is the rattling noise. Once cocked, noise is gone. This is normal from what I was unexplained. All good. Thank you.
Very professional and simple teaching pace that enable every airgun user to understand the bits and pieces of their gun and understand how things work. Thanks Ernest and please convey my appreciation to the whole FX team.
Excellent, thanks for the time and effort to produce these. It really makes a difference to have these available!
Great video this rifle is going to be my next purchase thank you Ernest
Me too
No tienes un video de cambio de calibre del wildcats?
I didnt see were you talked about adjusting the 1st regulator and where to read it, i assume you read it off of the same gauge as the 2nd regulator
No veo el ensamble de la sonda que empuja los pelets?
Hi Ernest,
Great video as always very informative, my question is I have the later MK3 with the brass bodied amp reg where you can remove the reg without stripping the whole of the reciever to
to access it, is it possible to fit an in reciever reg such as a Huma to get a double reg set up same as the bt version the Maverick and the Impact ?
o esta el paso donde instalas la sonda de el pelets
I got the screw replaced but cocking gun not as smooth on the pellet probe carrier do you screw it all the way in
Mine wont latch when cocking. Ill have to check for the 33mm and the factory grub screw marks. Maybe thats all it is.
In 22 caliber its my favorite gun. Insanely accurate and quiet.
Another great masterclass video, Is there an impact MK111 on the horizon?
Nothing at the moment. We’re very happy with the state of the MKII Impact with the power plenum.
I am having trouble with getting the sear back in correctly. The view of your video was not close enough, so I am a little bummed out. I will try and watch a couple more times. There are the 3 pin holes, to pin the sear, the pac-man assembly, and I believe you said a safety lock? Starting with the receiver upside down, the top hole #1-??, middle hole-??, and the bottom hole #3-??. I’m sure I am over thinking it. I know I should have recorded the takedown, that’s on my dumbass. Great video and I love my Cat III, but at this moment I can’t use it! 😭😭
My screw that goes inside prob broke off inside got new screw what do I need to do to replace it? Gun is Fx wildcat mkiii sniper bt
How do u adjust the timing.?
Hello
I have a new rifle FX Wildcat MK3 BT Compact cal.22
For cleaning reasons, I removed the barrel from the rifle by COMPLETELY unscrewing the two screws fixing the barrel of the rifle. On the official FX Airguns drawing, those two screws have references FX19086 (conical grub screw M6x8) and FX19955 (grub screw M8x6).
The FX19955 screw (grub screw M8x6) had some dried glue around it: I cleaned this dried glue completely.
I then reassembled the gun barrel and screwed the FX19086 (conical grub screw M6x8) and FX19955 (grub screw M8x6) screws.
Since then, every time I fire, the air under pressure escapes from the screw FX19955 (grub screw M8x6).
Should I put glue around this screw to avoid leakage?
If so, which one?
Could you help me
Vincent (from Belgium)
In the disassembly video you said to make sure the valve screw on top of the receiver only had a half turn on it. Is that literally, or did you mean to back it out half a turn?
Thank you for the videos. I want to ask about “Supreme” liner in .177 as my STX WC2 is extremely unreliable and I’m hoping for redemption. Thanks.
Nice engineering 👍🏻
Is there an FX Wildcat MkII reassembly? If so, I can't seem to find it.
love to see the MK2 also!!!
☺😊😀😁😂5 Smile's ( custom builds eq what if you wanted to add a FX kit to a ACR J10 gel blaster? )
My dream is to get a fx panthera, here in my country (Brazil) it costs the price of a car, without conditions, help me to get one. 0:04
Hi I have a question how do you adjust the length of the barrel placement in the block? I just got a wildcat mk3 sniper .30 and the brass sleeve over the barrel at the block is out to far and will not let the clip slide in. It's safe to shoot, had to hand load it to set it.
Yes, insert the magazine into the breach before tightening the grub screw holding the barrel in place.
有没有国内的
Hello
I have mk3 sniper version in .22
So I bought a .25 barrel
Can you tell me the best tune/settings to 25gr jsb kings to begin with?
I have a .25 wildcat mk3 sniper the stock settings are 110 bar reg and on power stand 7 it shoots the 25.4 grain jsb at 277ms 63 joules 69 shots before refill.
I use power 5 245ms 49 joules 115 shots very nice gun.
I love this gun and can’t afford it 😔 how about FX give me 75% off 🤗 Happy thanks giving.
Just received my wildcat mk3, something is loose and sliding back n forth near the power wheel.. any ideas? Is this normal? I have no idea, but seems like it should not have anything rattling .
Are you located in the United States?
If so please contact our technician team for more detailed assistance.
FX Airguns United States
Monday - Thursday 9 AM - 4 PM EST
Fridays 9 AM - 3 PM EST
Phone: +1 866 639 0772
serviceusa@fxairguns.com
If not you can E-mail Sweden customer service at Info@fxairguns.com
@@FXAirguns spoke to us tech support, when not cocked the free float hammer is the rattling noise. Once cocked, noise is gone. This is normal from what I was unexplained. All good. Thank you.
It’s normal
Niceliy
Muito inteligente
No tienes un video de cambio de calibre del wildcat?