Excellent video. Very clearly explained what to do. I couldn’t figure out how to get the plastic piece off to get to the foam maker stone. This cleared it up for me.
Thats a great video, I'll save that. I usually spray fresh water after use. But I don't store it upside down. It goes back on the bottle. Never an issue with it. I think rinsing it is very important after each use 👍
Sorted mine out nicely, wasn’t foaming at all anymore. Took it apart & everything looked clean including the gauze but leaving it to soak over night sorted it right out 👍🏻
*I haven't used it yet, however, this pressure washer replacement gun offers greater spray flexibility over the standard sprayer gun that came with my pressure washer originally.*
Hi Alfie. Great easy to follow video. What sort of concentration ratio do you use for the caustic soda solution? My tub says to Dissolve 55g (2 tablespoons) of caustic soda in 1 litre of COLD water for use as drain cleaning. Should i use the same dosage?
Far safer and a lot cheaper is to use citric acid powder. The stuff you can buy in Asian stores. I think it's mainly used for pickling but I use it to descale my kettle also. Just boil a kettle full of water and add a packet of the powder into a large mug. Costs 80 UK pennies. 👍
I question bro if I use it weekly once then how to maintain it I mean after how many weeks do I clean it by opening it or is it ok after shampoo work only spray water from bucket and ok ? Thanks in advance. Reply quickly.😜😎
Mas punya saya mjjc foam lance baru beli kenapa tidak bisa berbusa spt yang diharapkan alias masih encer padahal takaran dilution sdh benar.. Apa perlu ganti mesh filter atau nozzle yg lebih kecil lagi?? High pressure washer saya 120 bar Karcher
Alfie Renadhy in this case the O-ring is what's providing the seal so if you tape over it there is a chance the water can flow around it. It's probably fine to leave it as is, but when you already have a gasket or an o ring you don't need tape. It's odd they say to tape it.
Under normal circumstances, we DO NOT have to place teflon tape on the O-Ring connections. However, it is common to use teflon tape when the O-Ring is aged and worn. The ideal solution would be to change the O-Ring with new ones every time. There are also special lubricants on the market that help O-Rings to remain in good condition.
You're the man brother, thank you for another great video 👌 I wonder if one day you can do a video comparing this unit to the MTM Hydro 14.5001 PF22 Professional Foam Cannon. Cheers from NYC!
Under normal circumstances, we DO NOT have to place teflon tape on the O-Ring connections. However, it is common to use teflon tape when the O-Ring is aged and worn. The ideal solution would be to change the O-Ring with new ones every time. There are also special lubricants on the market that help O-Rings to remain in good condition. Beyond that, it's a great video, like many other videos on your channel. Well done! Keep going.
@@alfierenadhie In the plumbing (this is my profession), we use a kind of fat. But here, this is not drinking water, so the silicone grease is ok. I also usually use teflon tape for precautionary purposes. After all, it will never hurt the tool. *I wish I had discovered your videos with MJJC foam lance, before i bought the FJ6 karcher😌
Gan itu bersihinya harus rutin tiap bbrp kali pemakaian atau kalo pas ada keluhan aja gan? Emang pake shock itu ga ngerusak brass dan mesh filternya gan? Agan sampe sekarang pernah ganti sparepartnya foam lance ga gan?
@@alfierenadhie I dont understand, but yes mjjc sells the orifice, its works on Autobrite foamlance. Usually it comes with 1.25mm but if your pressure washer is weak use 1.1mm more foam.
![Noob To Max With DRAGON REWORK In Blox Fruits [FULL MOVIE]](http://i.ytimg.com/vi/LnBMOinoOvA/mqdefault.jpg)
Online Shop Ane Gan :
Shopee : bit.ly/2Z4QEWP
Tokopedia : bit.ly/2wxGtxy
Bukalapak : bit.ly/2Mm5PcC
great job bro alfie. i believe this is the only tutorial video on how to clean a foam lance on youtube. if not, this must be the best one!
Mate, this is an outstanding video. I finally cleaned my foaming cannon, by using your methods shown here. 10 out of 10. Thank you very much. Ace!
Excellent video. Very clearly explained what to do. I couldn’t figure out how to get the plastic piece off to get to the foam maker stone. This cleared it up for me.
I didnt even buy a MTM yet, and i watched this because its so well done. Great job.
Thanks a lot you have saved me money and time, yesterday i watched your video and fixed my mjjc classic cannon. 😊
This is gold! Thank you brother for share!! 👏👏👏
Is there a way I can tighten the feel of the top foam adjustment knob?
Worked first time, thanks for this video. I will certainly recommend this to fellow detailers.
Alfie you are a star mate, thanks. you just saved me from buying a new one.
1:55 in the video for me it’s impossible to get that piece off the snow foam lance
Thats a great video, I'll save that. I usually spray fresh water after use. But I don't store it upside down. It goes back on the bottle. Never an issue with it. I think rinsing it is very important after each use 👍
Sorted mine out nicely, wasn’t foaming at all anymore. Took it apart & everything looked clean including the gauze but leaving it to soak over night sorted it right out 👍🏻
*I haven't used it yet, however, this pressure washer replacement gun offers greater spray flexibility over the standard sprayer gun that came with my pressure washer originally.*
is a 1.1mm orifice better for a nilfisk c110?
mine , pin got rusted and hard to push how to release the pin?
Hi Alfie. Great easy to follow video. What sort of concentration ratio do you use for the caustic soda solution? My tub says to Dissolve 55g (2 tablespoons) of caustic soda in 1 litre of COLD water for use as drain cleaning. Should i use the same dosage?
Great guide, thanks Alfie. Anyone know where a set of replacement o-rings can be sourced?
Any luck finding the correct o-rings ? There are tree different sizes on the foam cannon. Very difficult too find the wright ones.
Try electric tools shop that's selling air compressor.
Kak Alfie beli high pressure power wsahernya dimana yah ?
mas, kalau untuk MJJC juga sama perawatannya??
Alfie, di mana saya boleh dapatkan Nozzel 1.1mm untuk Autobrite seperti yg anda gunakan itu
Far safer and a lot cheaper is to use citric acid powder. The stuff you can buy in Asian stores. I think it's mainly used for pickling but I use it to descale my kettle also.
Just boil a kettle full of water and add a packet of the powder into a large mug. Costs 80 UK pennies. 👍
15x ive watched ur video id think i know by memory how to do it but not yet cleaned up my cannon for 7+ years now
Please.. How to maintain snow foam mjjc..
See at the end of video
Thank’s
Also apply some silicone grease to the o-rings.
I question bro if I use it weekly once then how to maintain it I mean after how many weeks do I clean it by opening it or is it ok after shampoo work only spray water from bucket and ok ? Thanks in advance. Reply quickly.😜😎
Very Clear direction, I like it
Excellent video - Thank you, I learnt a lot This will help me a lot.
cairan pertama apa namanya ya?, dan cairan untuk bilasnya.. pake cuka ya gan?
I ordered the foam cannon from chemical guys, but it sprays horizontaly not verticaly. So can change it somehow?
Alfie Renadhy better I leave it as it is ... but I think its better it sprays verticaly ...
ub
Very helpful and well made. Thank you.
thanks thought I was going to have to buy another great instructions very clear sorted now
Mas beli nozzle tip nya dimana dan ukurannya 1.1 atau1.25 mm. Terimakasih
Ga ada jual kalo autobrite gan
Thank you brother your method is hundred percent good my problem SOL thank you very much
took mine apart uesd my air compressor to clean and works great again :-)
is this foam lance good for nilfisk c-130?
The best!
Mas punya saya mjjc foam lance baru beli kenapa tidak bisa berbusa spt yang diharapkan alias masih encer padahal takaran dilution sdh benar..
Apa perlu ganti mesh filter atau nozzle yg lebih kecil lagi??
High pressure washer saya 120 bar Karcher
bro itu autobrite beli di ebay. pas nyampe di indonya kena urusan cukai lagi nga? Makasih
ok deh.. itu biasa dikirim lewat pos yah gan? saya test coba beli lance juga ^^.
You shouldn't use teflon tape if you have an o-ring seal already. You could introduce a leak.
Alfie Renadhy in this case the O-ring is what's providing the seal so if you tape over it there is a chance the water can flow around it. It's probably fine to leave it as is, but when you already have a gasket or an o ring you don't need tape. It's odd they say to tape it.
I would say it's ok to put the Teflon tape on the threaded section only, carefully of course so not to contact any part of the o-ring.
Under normal circumstances, we DO NOT have to place teflon tape on the O-Ring connections. However, it is common to use teflon tape when the O-Ring is aged and worn. The ideal solution would be to change the O-Ring with new ones every time. There are also special lubricants on the market that help O-Rings to remain in good condition.
You're the man brother, thank you for another great video 👌
I wonder if one day you can do a video comparing this unit to the MTM Hydro 14.5001 PF22 Professional Foam Cannon.
Cheers from NYC!
Brilliant video.
Peças de reposição onde comprar
Cool, Keren Videonya, sangat bermanfaat buat nubie yang baru mau belajar car care nih....Thanks!
Great how to video. Thanks Alfie
Under normal circumstances, we DO NOT have to place teflon tape on the O-Ring connections. However, it is common to use teflon tape when the O-Ring is aged and worn. The ideal solution would be to change the O-Ring with new ones every time. There are also special lubricants on the market that help O-Rings to remain in good condition.
Beyond that, it's a great video, like many other videos on your channel. Well done! Keep going.
@@alfierenadhie In the plumbing (this is my profession), we use a kind of fat. But here, this is not drinking water, so the silicone grease is ok. I also usually use teflon tape for precautionary purposes. After all, it will never hurt the tool.
*I wish I had discovered your videos with MJJC foam lance, before i bought the FJ6 karcher😌
Fantastic video
thanks for the helpful video, I don't have a vice and do t know why my pa lance doesn't work. I'm just going to buy a £20 lance of Amazon
Nice.... how many time you will clean the foam cannon
for a daily carwash business?
wyn after every use rinse with water. Fill foam cannon with Just water
5:13 كأني أسمع صوت آذان ولا :)
I tried this but my Lance just froths out on the floor
Very nice video bro...very detail...done subs
Good Tips at the end of the video.. Bravo!
Gan itu bersihinya harus rutin tiap bbrp kali pemakaian atau kalo pas ada keluhan aja gan? Emang pake shock itu ga ngerusak brass dan mesh filternya gan? Agan sampe sekarang pernah ganti sparepartnya foam lance ga gan?
@@alfierenadhie tq gan info nya
TySm sir best video n helpful 💯🥰
Excellent tutorial!
tinggal bikin video cara bersihin engine bay
Nice style, fella! 👍🏻
what the heck this guy in Indonesia has made in the USA parts... I live in the USA and can barely find anything made in the USA xD
Made in Italy they are.
Bawaan autobrite pake orifice 1.25 ato 1.1 bro??
@@alfierenadhie I dont understand, but yes mjjc sells the orifice, its works on Autobrite foamlance.
Usually it comes with 1.25mm but if your pressure washer is weak use 1.1mm more foam.
How much your lance ?
3:56 itu pakai sealtape kran air??
Lah emang
my snowfoam only produce water, where is the problem?
Great tutorial thanks
It Just Works
that was super helpful
Very helpful, thank you very much
Thank you so much for the video, he help me a lot too !
Man you go all out!
So you need a weekend and a degree in engineering to clean a badly designed snow foam. The filter should be easily removable.
Great video. Thanks.
Excellent video!!!!!
very good thanks dee
In can't wait to arive ! NIce product!
Good job bro
Muy bueno el canal ...
Ну и где пена??????? Может он нерабочий и пены не даёт.
Thanks for the vid
Thanks. Just repaired mine too!
Thanks fof the info m8 🖒
fantastic
Kereen videonya
👍👍
With what you spend on getting it clean, not to mention your time, one can buy a new one for $15 bucks.
His one can cost up to 60 AUD
Michael L
... Yes, fuck the planet and crush the wallet -.-
totally agree. of course the huggers won't like that
I have a 20dollar amazon cannon that I will put up against anyone’s mtm. On that note I will just purchase another one
Thanks for the great idea........ jus buy a new one!
Nice video. Too many bokeh for me
raaafu8
My pin do hard to remove any idea?
Great video!
Great video, thank you