Will the C6 Corvette Grand Sport Run after the Cam and Converter Install?! (We Will Find Out)
HTML-код
- Опубликовано: 5 окт 2024
- Will the C6 Corvette Grand Sport Run after the Cam and Converter Install?! (We Will Find Out)
Want TWA Motorsports Merch? Go to www.twamotorsports.com and pick some up!
Parts Used
Cam and Cam Install Parts Matt@GPTuning
ATI Balancer amzn.to/446YRw4
ARP Balancer Bolt amzn.to/3xIxWLe
Power Stop Rear Brakes amzn.to/3Q76e0Q
Redline Power Steering Fluid amzn.to/4aTZLhG
Transmission Fluid amzn.to/4aAKaEj
Differential Fluid amzn.to/3W4kueS
Spark Plugs amzn.to/3TXouLk
Oil Used amzn.to/3Q4XiJi
Silicone amzn.to/4aQLEdm
Tools Used
Crank Pin Tool amzn.to/3W4aaDj
Cylinder Air Attachment amzn.to/4auOQLL
LS Valve Spring Tool amzn.to/4aDV6Rl
Magnet amzn.to/3Uk6lZC
Balancer Installation Tool amzn.to/4aQLRxa
Brake Bleeding Container amzn.to/3W5I5Mc
Assembly Lube amzn.to/4d3IXqm
Timing Cover Alignment Tool amzn.to/4cK68pF
Balancer Puller amzn.to/3PQrjwB
Corvette Jacking Pucks amzn.to/3Vjbyl9
Torque Wrench amzn.to/3IamaeC
In Lb Torque Wrench amzn.to/445JeoF
LED Light amzn.to/42Id4z0
Gloves amzn.to/3XCeitd
Microfiber Towels amzn.to/43chzka
Milwaukee Ratchet amzn.to/3PTfZ2D
Other Parts on the Car
Cam Retainer amzn.to/3TZNJ0J
Cam Retainer Bolts amzn.to/3U3nsi0
Timing Cover Seal amzn.to/43NkBgn
Timing Cover Gasket amzn.to/4al5iy9
Torque Converter www.circledspe...
Oil Pump Pick Up Tube O Ring amzn.to/3J3OoYM
Headers speed-engineer...
X-Pipe(Off Road Only) speed-engineer...
Header Gaskets amzn.to/3rfqpjG
ARP Header Bolts amzn.to/3XGuSrD
O2 Extension Harness amzn.to/3O3V5xr
Heat Wrap Velcro amzn.to/43eHmYI
Spark Plugs amzn.to/3NEubL4
Mild to Wild Exhaust Switch amzn.to/44bGR3b
Spoiler Used www.rpidesigns...
Other Spoiler Options amzn.to/3KEYaBJ
MSD Plug Wires amzn.to/3s6TEFY
We are picking up where we left off on Kohen's C6 Corvette Grand Sport. After all the stuff we have removed, do you think it will start. We finish up the cam install from Matt @ GP Tuning. We get the transmission are rear end full after the circle d 3200 stall converter install. For the front we did use a trunnion upgrade which you saw in the last video. Next because of the cam size we had to install dual valve springs. The requires new valve seals and locators. The kit comes with all you need including titanium retainers and locks. This job is easier with the engine out but with the tools we had Kohen got it accomplished. We added new hardened push rods and bolted the rockers back down with some assembly lube. We did upgrade to an ATI Balancer or Harmonic Balancer for a couple reasons. 1. Corvette has had issues with balancers coming off or going bad. 2. He wants to upgrade to a blower or procharger down the road so we will need the ati for that also. Since he plans to put a supercharger on it we did pin the crank with the kit listed above. It isn't too bad but you don't have a lot of room. It was then time for assembling the rest of the parts we removed and adding fluid. Kohen did upgrade the rear brakes to power stops and we will be doing the fronts as money becomes available. He and I were nervous to start it up but it fired right up and seems to be doing good so far. Hit the Comments and let me know what you think.......
Thanks For Watching!!!!
Want to Send Stuff
TWA Motorsports
PO Box 190
Aurora MO 65605
Subscribe and Follow TWA Motorsports
RUclips: / twamotorsports
Instagram: / twamotorsports
Email: twamotorsports@hotmail.com
Video Equipment used to make this video(Need to update)
Gopro Hero 9 amzn.to/3FMXiI3
GoPro Mount amzn.to/3pf1HvX
Gopro Session amzn.to/2IZprAp
Video editing amzn.to/3KC27HO
Photo editing amzn.to/3KC27HO
As Always Thanks For Watching!!!!!!
Do this at your own risk. For entertainment purposes only
SUBSCRIBE FOR MORE VIDEOS!!!!
Disclaimer:This video and description contains affiliate links, which means if you click on a product link, I'll receive a small commission.
Good job Kohen on all the wrench turning on the C6, that was a major project. Always feels better when you can do your own work. Travis, looks like the apples didn't fall far from the tree, these are memories they'll never forget. ✌🏻
Definitely. Stressful but will look back and remember these days forever
Corvette *never ending project*
Trans am in the background “am I a joke to you?”
True
Sounds so good. Proud of both of you guys and your hard work!
Thank you
Awesome , showing your son the ropes. Love the content. 👍🏼
Thank you. Been stressful but fun
Sounds and looks good!!👍
Thank you
Nice! Any plans to dyno it in the future?
We may end up doing that
Sweet. Great family time....
I agree on some days
😂😂
Lol
My opinion doesn’t mean shit so here I go. I pause the video at 3: 54 and paused it,I zoomed in to the spring and retainer image. Those retainers do not locate those springs for shit. If you look at the number one cylinder the spring looks like it’s pushed all the way off the retainer. The OD of the spring is quite a bit bigger than the OD retainer. What brand is this stuff?
We were test fitting. They cover and it was installed incorrectly at first
C7 is my other dream car! lol
They are nice
18 was a little spicy!
Way too spicy
Good job Cohen way to go.. feels good to do your own work on your car rather than bring it to someone to modify it..👍
Indeed
@@TWAMotorsports made me laugh in the video. 😂😂😂
@Bird-dl7xs lol
you sound tired..cool video though.
I am.
Too many projects that he is trying to do.
Exactly